HP StorageWorks ESL E Series Gebrauchs- und Pflegehandbuch

StorageWorks

ESL E-Series

Ultrium FC Drive

Replacement

StorageWork s

Caution:Parts canbedamagedby

electrostaticdischarge. Keepparts in their

containers until needed. Ensureyouare

properlygroundedwhentouchingstatic-

sensitive components.

Note:This part is hot-pluggable. It is not

necessaryto power downthelibraryto

replace this part.

Tapedrivesclusters are

numberedstartingat

thetopof the

cabinet as follows:

0,1, 2, 3, 4, 5.

In eachcluster the

drives areidentified

as follows: top

right is A, topleft

is B, bottom right

is C, bottom left is

D. Adrawing

showingthis is on

theinsideof theback

door.

Opentheback door of thelibrary.

Inspect thecontents of thekit.

StorageWorks

ESL

E-series

TapeDrive

Caution:Partscanbedamagedby

electrostaticdischarge.Keeppartsintheir

containersuntilneeded.Ensureyouare

properlygroundedwhentouchingstatic-

sensitivecomponents.

Note:Thispartishot-pluggable.Itisnot

necessarytopowerdownthelibraryto

replacethispart.

Identifythetapedrivetobereplaced.TheLEDof

thedrivewillberedoroff.

Tapedrivesclustersare

numberedstartingat

thetopofthe

cabinetasfollows:

0,1,2,3,4,5.

Ineachclusterthe

drivesareidentified

asfollows:top

rightisA,topleft

isB,bottomright

isC,bottomleftis

D.Adrawing

showingthisison

theinsideoftheback

door.

Openthebackdoorofthelibrary.

Inspectthecontentsofthekit.

From the Operator Control Panel (OCP), power off

the drive to be replaced.

From Menu, select the Ops button.

Use the Up and Downbuttons to select the

drive, then press the Selectbutton.

Use the Up and Downbuttons to change the

drive to off-line, then press the Selectbutton.

Select the Backbutton to return to Menu.

Verify that the correct drive is powered down.

ESL E-Series

Ultrium 460

NFC Drive

Replacement

Caution: Parts can be damaged by

electrostatic discharge. Keep parts in their

containers until needed. Ensure you are

properly grounded when touching static-

sensitive components.

Note: This part is hot-swappable. It is not

necessary to power down the library to

replace this part.

Drive clusters are

numbered from 0 to 5

starting at the top

of the cabinet. In

each drive cluster

the drives are

identified as

follows: top right

is A, top left is B,

bottom right is C,

bottom left is D.

A drawing of

the drive cluster is

located on the

inside of the back door.

Open the back door of the library.

Inspect the contents of the kit.

From the Home screen, select the Ops button.

a. From Menu, select the Ops button.

b. Use the Up and Down buttons to select the

drive, then press the Select button.

c. Use the Up and Down buttons to change the

drive to off, then press the Select button.

d. Select Yes to confirm.

e. Select the Back button to return to Menu.

f. Verify that the correct drive is powered down.

Printed in the US

Second Edition (March 2005)

Part Number: 358832-002

*358832-002*

358832-002

Getting help

• HP product information:

http://www.hp.com/products/esle

• HP technical support and phone numbers:

http://www.hp.com/support

• HP StorageWorks Library and Tape Tools

(L&TT) diagnostic software:

http://www.hp.com/support/tapetools

• Interface Manager and HP StorageWorks

Command View TL:

http://www.hp.com/support/cvtl

Firmware Upgrade

If necessary, upgrade the drive firmware

using the Interface Manager's command-line

interface. Refer to the HP StorageWorks

Interface Manager and Command View TL

User Guide for detailed procedures on

upgrading drive firmware.

Close the back door of the library.

Drive Replacement

Drive Removal

Remove the FC cable from the cable clip.

1) Insert the new drive into the

vacant drive bay. 2) Tighten the captive

screw to secure the drive to the cluster.

Using a

slotted screwdriver,

1) loosen the captive screw at

the upper left corner of the drive module.

2) Move the FC cable to the side and out of the

way. Grasp the drive handle and pull the drive

from its bay.

Verify that the FC port LED on the FC interface

controller card is green.

The LED for the replaced

drive and its associated

cluster controller card LED

should be green.

14 15

Make sure that Command View TL recognizes

the replaced drive using the Command View TL

console. Refer to the HP StorageWorks

Interface Manager and Command View TL

User Guide for detailed procedures.

CAUTION: To avoid damaging FC cables,

do not sharply bend or pinch them. Allow a

radial bend when reattaching the FC cables.

Note: If needed, the tie wrap provided

with this kit can be used to help keep

the FC cables clear of the drive cluster

below by attaching the cables to the

drive handle.

Power on the drive by completing the following

steps from the OCP for the new drive.

a. From Menu, select the Ops button.

b. Use the Up and Down buttons to select the

drive, then press the Select button.

c. Use the Up and Down buttons to change the

drive to on-line, then press the Select button.

d. Select the Back button to return to Menu.

Use the Command View TL user interface to

reboot the interface controller card. Refer to

the HP StorageWorks Interface Manager and

Command View TL User Guide for detailed

procedures.

Connect the FC cable to the new drive. The FC

cable connector clicks into place. Insert the cable

into the cable clip on the drive.

Identify the drive to be replaced.

The LED of the drive to be replaced will be off.

CAUTION: To avoid damaging the drive,

do not remove it if the LED is still lit.

See step 2 to power off the drive.

Disconnect the Fibre Channel (FC) cable from the

drive to be replaced by 1) pressing down on the

cable connector tab and 2) pulling the connector

away from the drive.

CAUTION: To avoid damaging FC

cables, do not sharply bend or pinch them.

Drive Replacement

Drive Removal

Remove the FC cable from the cable clip.

1) Insert the new drive into the

vacant drive bay. 2) Tighten the captive

screw to secure the drive to the cluster.

Using a

slotted screwdriver,

1) loosen the captive screw at

the upper left corner of the drive module.

2) Move the FC cable to the side and out of the

way. Grasp the drive handle and pull the drive

from its bay.

Verify that the FC port LED on the FC interface

controller card is green.

The LED for the replaced

drive and its associated

cluster controller card LED

should be green.

14 15

Make sure that Command View TL recognizes

the replaced drive using the Command View TL

console. Refer to the HP StorageWorks

Interface Manager and Command View TL

User Guide for detailed procedures.

CAUTION: To avoid damaging FC cables,

do not sharply bend or pinch them. Allow a

radial bend when reattaching the FC cables.

Note: If needed, the tie wrap provided

with this kit can be used to help keep

the FC cables clear of the drive cluster

below by attaching the cables to the

drive handle.

Power on the drive by completing the following

steps from the OCP for the new drive.

a. From Menu, select the Ops button.

b. Use the Up and Down buttons to select the

drive, then press the Select button.

c. Use the Up and Down buttons to change the

drive to on-line, then press the Select button.

d. Select the Back button to return to Menu.

Use the Command View TL user interface to

reboot the interface controller card. Refer to

the HP StorageWorks Interface Manager and

Command View TL User Guide for detailed

procedures.

Connect the FC cable to the new drive. The FC

cable connector clicks into place. Insert the cable

into the cable clip on the drive.

Identify the drive to be replaced.

The LED of the drive to be replaced will be off.

CAUTION: To avoid damaging the drive,

do not remove it if the LED is still lit.

See step 2 to power off the drive.

Disconnect the Fibre Channel (FC) cable from the

drive to be replaced by 1) pressing down on the

cable connector tab and 2) pulling the connector

away from the drive.

CAUTION: To avoid damaging FC

cables, do not sharply bend or pinch them.

StorageWorks

ESL E-Series

Ultrium FC Drive

Replacement

StorageWork s

Caution:Parts canbedamagedby

electrostaticdischarge. Keepparts in their

containers until needed. Ensureyouare

properlygroundedwhentouchingstatic-

sensitive components.

Note:This part is hot-pluggable. It is not

necessaryto power downthelibraryto

replace this part.

Tapedrivesclusters are

numberedstartingat

thetopof the

cabinet as follows:

0,1, 2, 3, 4, 5.

In eachcluster the

drives areidentified

as follows: top

right is A, topleft

is B, bottom right

is C, bottom left is

D. Adrawing

showingthis is on

theinsideof theback

door.

Opentheback door of thelibrary.

Inspect thecontents of thekit.

StorageWorks

ESL

E-series

TapeDrive

Caution:Partscanbedamagedby

electrostaticdischarge.Keeppartsintheir

containersuntilneeded.Ensureyouare

properlygroundedwhentouchingstatic-

sensitivecomponents.

Note:Thispartishot-pluggable.Itisnot

necessarytopowerdownthelibraryto

replacethispart.

Identifythetapedrivetobereplaced.TheLEDof

thedrivewillberedoroff.

Tapedrivesclustersare

numberedstartingat

thetopofthe

cabinetasfollows:

0,1,2,3,4,5.

Ineachclusterthe

drivesareidentified

asfollows:top

rightisA,topleft

isB,bottomright

isC,bottomleftis

D.Adrawing

showingthisison

theinsideoftheback

door.

Openthebackdoorofthelibrary.

Inspectthecontentsofthekit.

From the Operator Control Panel (OCP), power off

the drive to be replaced.

From Menu, select the Ops button.

Use the Up and Downbuttons to select the

drive, then press the Selectbutton.

Use the Up and Downbuttons to change the

drive to off-line, then press the Selectbutton.

Select the Backbutton to return to Menu.

Verify that the correct drive is powered down.

ESL E-Series

Ultrium 460

NFC Drive

Replacement

Caution: Parts can be damaged by

electrostatic discharge. Keep parts in their

containers until needed. Ensure you are

properly grounded when touching static-

sensitive components.

Note: This part is hot-swappable. It is not

necessary to power down the library to

replace this part.

Drive clusters are

numbered from 0 to 5

starting at the top

of the cabinet. In

each drive cluster

the drives are

identified as

follows: top right

is A, top left is B,

bottom right is C,

bottom left is D.

A drawing of

the drive cluster is

located on the

inside of the back door.

Open the back door of the library.

Inspect the contents of the kit.

From the Home screen, select the Ops button.

a. From Menu, select the Ops button.

b. Use the Up and Down buttons to select the

drive, then press the Select button.

c. Use the Up and Down buttons to change the

drive to off, then press the Select button.

d. Select Yes to confirm.

e. Select the Back button to return to Menu.

f. Verify that the correct drive is powered down.

Printed in the US

Second Edition (March 2005)

Part Number: 358832-002

*358832-002*

358832-002

Getting help

• HP product information:

http://www.hp.com/products/esle

• HP technical support and phone numbers:

http://www.hp.com/support

• HP StorageWorks Library and Tape Tools

(L&TT) diagnostic software:

http://www.hp.com/support/tapetools

• Interface Manager and HP StorageWorks

Command View TL:

http://www.hp.com/support/cvtl

Firmware Upgrade

If necessary, upgrade the drive firmware

using the Interface Manager's command-line

interface. Refer to the HP StorageWorks

Interface Manager and Command View TL

User Guide for detailed procedures on

upgrading drive firmware.

Close the back door of the library.

Andere Handbücher für StorageWorks ESL E Series

Andere HP Lagerung Handbücher

HP Storevirtual 4000 Bedienungsanleitung

HP XP7 Bedienungsanleitung

HP D7171A - NetServer - LPr Bedienungsanleitung

HP 3000 - 37XE System Bedienungsanleitung

HP StorageWorks XP1024 Kurzanleitung

HP StorageWorks 9000 Virtual Libr Bedienungsanleitung

HP StoreEasy 3000 Service-Handbuch

HP StorageWorks XP48 - Disk Array Bedienungsanleitung

HP StorageWorks 3800ux Bedienungsanleitung

HP Storevirtual 4000 Bedienungsanleitung

HP 705 Kurzanleitung

HP D2D Bedienungsanleitung

HP EVA P6000 Bedienungsanleitung

HP StorageWorks DAT 72 Gebrauchsanweisung

HP 705 Kurzanleitung

HP StorageWorks 12000 Leitfaden

HP StorageWorks XP10000 - Disk Array Bedienungsanleitung

HP Storevirtual 4000 Bedienungsanleitung

HP MSL4048 - StorageWorks Ultrium 920 Tape... Bedienungsanleitung

HP Surestore 160ex - Optical Jukebox Bedienungsanleitung

HP Storevirtual 4000 Kurzanleitung

HP StorageWorks XP1024 Kurzanleitung

HP StorageWorks 2500 Bedienungsanleitung

HP XP7 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung