HP Storevirtual 4000 Kurzanleitung

HP LeftHand Storage SRA for VMware SRM

Deployment Guide

HP Part Number: AX696-96210

Published: November 2012

Edition: 2

1 Using the HP LeftHand Storage Replication Adapter

Software for VMware vCenter SRM 5.x

The HP LeftHand Storage Replication Adapter Software for VMware vCenter SRM enables full

featured use of the VMware Site Recovery Manager. Combining Remote Copy replication with

VMware SRM provides an automated solution for implementing and testing disaster recovery

between geographically separated sites.

Configuring SRA

A typical SRM configuration involves two geographically separated sites with TCP/IP connectivity,

the protection site and the recovery site. The protection site is the site that is being replicated to

the recovery site for disaster recovery. Each site contains HP LeftHand Storage, ESX servers, a

Virtual Center Server, and an SRM server.

Figure 1 Typical SRM configuration with two geographically separate sites

Requirements

•SAN/iQ release 9.5 or later

•64-bit Windows OS

•.Net 3.5 will be installed if not present

•VMware vCenter running on two sites

Configuring SRA 3

Installing SRA

First install the VMware SRM at each site, and then install the SRA on the SRM server at each site.

Once the SRA is installed, the SRM can discover replicated volumes between sites by configuring

arrays in the SRM. Configuring HP LeftHand Storage arrays in the SRM requires the following:

•The IP addresses of the SAN/iQ managers. More than two addresses can be input by using

a comma or semicolon separator.

•The same user name and password in each site. This is the administrative user name and

password configured in the CMC.

The user at the recovery site must have full permissions on the management group but can be

limited to read only on all other permissions.

Installing HP LeftHand Application Aware Snapshot Manager (optional)

Install and configure the Application Aware Snapshot Manager on both Primary and Remote site

VCenter servers. For installation instructions, see the HP LeftHand Storage Application Aware

Snapshot Manager Deployment Guide

The replication schedule controls the application aware snapshot integration. If the schedule has

managed enabled then that enables the application managed snapshot integration, where in SRA

takes managed snapshots in syncOnce and reports to the SRM the recovery points with VM

snapshots using VmImageConsistencyEnabled flag. If the schedule has managed disabled then

that disables the application managed snapshot integration as no managed snapshots are taken.

Exceptions: The SRA can handle any changes in configuration, but this is a normal, baseline

scenario.

How the SRA works with VMware SRM 5.x

The SRA has three primary functions for the SRM:

•Test Failover—A Test scenario that checks failover conditions and parameters. This will create

temporary writable sources at the Backup Site. In the case of HP LeftHand Storage, SmartClone

volumes will be created.

•Failover—Transitioning production services from a Primary Site to a Backup Site, with the

Primary Site either available or not.

•Reprotect—After a Failover, planned or unplanned, transitioning production services from the

Backup Site back to the Primary Site. This entails reversing Replication so Replication goes

from Backup to Primary Site, doing a Failover in Reverse, and then reversing Replication again

so replication goes from the Primary to Backup Site.

These functions each depend on specific configuration information in a HP LeftHand Storage

management group.

Array and volume discovery

The SRM gets information from the SRA about what volumes are being replicated by the SAN/iQ

software. The SRM then compares that list to the volumes it recognizes in a VMware environment.

For normal SRM operation, a replicated volume needs to have a Remote Copy schedule with

completed remote copies at a different HP LeftHand Storage management group under a remote

volume that is not mounted at the remote site. This is a standard HP LeftHand Storage Remote Copy

configuration.

For instructions on how to configure Remote Copy schedules, see the HP LeftHand Storage Remote

Copy User Guide. The latest version of this document can be found at: http://www.hp.com/

support/LeftHandManuals. The same information is available from the HP LeftHand Storage Online

Help in the HP LeftHand Centralized Management Console.

4 Using the HP LeftHand Storage Replication Adapter Software for VMware vCenter SRM 5.x

Volumes recognized by the SRA

Volumes must be configured with scheduled remote snapshots or they will not be considered for

the SRM by the SRA. The SRA recognizes the scheduled remote snapshots as replicated LUNs for

the SRM to manage. Volumes that are being remote copied only manually are not updated

consistently enough to be useful for disaster recovery and the SRM.

If a volume has scheduled remote snapshots, and you create an ad hoc manual remote snapshot

of that volume, then the SRA will recognize the manual remote snapshot along with the scheduled

remote snapshots. Such ad hoc remote snapshots may be useful to test failover with a more recent

copy than the schedule has, or to push the latest updates to the remote site before a foreseeable

disaster occurs.

IMPORTANT: A volume in the protected site should not have two or more schedules going to

multiple volumes on the same remote management group.

Volumes ignored by the SRA

Remote snapshots within the same HP LeftHand Storage management group are ignored. These

snapshots are not considered disaster recovery copies since they are usually created to clone a

volume in the HP LeftHand Storage, and copies that reside on the same SAN are not useful for

disaster recovery.

Testing failover at the recovery site

The SRM performs test failovers at the recovery site when requested. When test failovers are

requested, the SRA performs the following steps:

1. Select the replicated volumes.

2. Identify the latest complete Remote Copy snapshot.

3. Delete any temporary writable space on that snapshot to ensure an unedited snapshot is

presented to ESX servers.

Use this snapshot to create a SmartClone volume.

4. Configure authentication for ESX servers to directly mount SmartClone volumes.

5. When testing stops, to conserve space on the SAN, delete the temporary writable space that

was used during the test.

Actual failover at the recovery site

In the event of a disaster, the SRM can perform actual failover when requested to. When actual

failover is requested, the SRA performs the following steps:

1. Select the replicated volumes.

2. Identify and remove any incomplete remote copies that are in progress and present the most

recent completed Remote Copy as a primary volume.

3. Convert remote volumes into primary volumes and configure authentication for ESX servers to

mount them.

If an actual failover does not run completely for any reason, the failover can be called many times

to try to complete the run. If, for example, only one volume failed to restore and that was due to

a normal snapshot being present, the snapshot could be manually deleted and the failover be

requested again.

Reprotect at the recovery site

After a failover, the SRM can perform reprotect when requested to. When actual reprotect is

requested, the SRA performs the following steps:

How the SRA works with VMware SRM 5.x 5

1. On the original protected site (which will become recovery site after reprotect is executed)

a. Pause any schedules going from the primary volume to the remote volume.

b. Remove any ESX Server assignments.

c. Change the primary volume to the backup volume.

2. On the original recovery site (which will become protected after reprotect is executed), create

a remote schedule with the primary volume as the target, or un-pause remote schedules.

3. Delete any SRA-created snapshots and schedules.

Troubleshooting the SRA

Table 1 Troubleshooting the SRA

SolutionCauseProblem

Install the SRA and restart the VMware

SRM Service.

The SRA might not be installed or the

SRM service has not restarted since

the SRA was installed.

The HP LeftHand Storage array does

not appear in the drop down list of

arrays for the SRM.

Create a Remote Copy schedule for all

volumes that are to be managed by the

SRM.

Volumes are only reported as

replicated to the SRM if they have a

Remote Copy schedule.

The SRM does not see the volumes that

are replicated.

Create authentication groups for any

CHAP authentication required on the

The SRM does not store or pass CHAP

passwords to the SRA. For CHAP

CHAP-authenticated ESX servers are

failing to perform test failovers or

actual failover. recovery site before running test failover

or failover.

authentication to work, the

authentication group with correct

password must be already configured

on the SAN/iQ management group.

Configure a network that can route from

the SRM servers to the HP LeftHand

SRM servers running the SRA must be

able to route TCP/IP traffic to the SAN

The SRA fails to connect to the SAN.

Storage, and verify the user account

configured in the SRM.

that is to be managed, and must have

a valid username and password.

Do not mount primary and remote

volumes at the same site at the same

time.

Both the primary and remote volume

might be mounted at the same site.

When the HP LeftHand Storage array

is discovered, an error message states

there are duplicate LUNs.

TIP: Read the messages that are displayed in the SRM UI during various functions as they provide

useful information.

6 Using the HP LeftHand Storage Replication Adapter Software for VMware vCenter SRM 5.x

2 Documentation feedback

HP is committed to providing documentation that meets your needs. To help us improve the

documentation, send any errors, suggestions, or comments to Documentation Feedback

([email protected]). Include the document title and part number, version number, or the URL

when submitting your feedback.

Andere Handbücher für Storevirtual 4000

Inhaltsverzeichnis

Andere HP Lagerung Handbücher

HP C6388B Bedienungsanleitung

HP 3PAR StoreServ 7200 2-node Bedienungsanleitung

HP XP7 Bedienungsanleitung

HP AJ765A - StorageWorks RDX Removable Disk Backup... Bedienungsanleitung

HP Ultrium 215 Gebrauchsanweisung

HP VS80 - StorageWorks DLT VS 80 Tape Drive Bedienungsanleitung

HP C2246 Produkthandbuch

HP StorageWorks NAS 1000s Bedienungsanleitung

HP AH164A - StorageWorks 1/8 G2 Tape Autoloader Ultrium... Bedienungsanleitung

HP v229g Bedienungsanleitung

HP StorageWorks 2000i Bedienungsanleitung

HP StorageWorks 6000 - Virtual Library System Bedienungsanleitung

HP P9000 Bedienungsanleitung

HP 3PAR StoreServ 7200 2-node Bedienungsanleitung

HP DW017B - StorageWorks Ultrium 448 Tape Drive Bedienungsanleitung

HP StorageWorks DAT 40i Bedienungsanleitung

HP StorageWorks 1500cs - Modular Smart Array Bedienungsanleitung

HP surestore t20xe Bedienungsanleitung

HP StorageWorks XP10000 - Disk Array Bedienungsanleitung

HP StorageWorks 12000 Bedienungsanleitung

HP StorageWorks 8B - FC Entry Switch Bedienungsanleitung

HP DW017B - StorageWorks Ultrium 448 Tape Drive Bedienungsanleitung

HP LTO-2 HH Bedienungsanleitung

HP HPE StoreEver LTO-8 Ultrium Tape Produkthandbuch

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung