HPE ProLiant Bedienungsanleitung

Intelligent Provisioning 4.20 User Guide for HPE ProLiant and Synergy Gen11Intelligent Provisioning 4.20 User Guide for HPE ProLiant and Synergy Gen11

ServersServers

Part Number: 30-A50246BA-420

Published: May 2023

Edition: 2

Intelligent Provisioning 4.20 User Guide for HPE ProLiant and Synergy Gen11 ServersIntelligent Provisioning 4.20 User Guide for HPE ProLiant and Synergy Gen11 Servers

AbstractAbstract

This document details how to access and use the Intelligent Provisioning and HPE Rapid Setup Software, including tasks such as installing an

OS, updating firmware, software, and drivers, and performing some diagnostic tests. Intelligent Provisioning is included in the optimized

server support software from the Service Pack for ProLiant (SPP). This document is intended for administrators experienced in using

ProLiant Gen10 Plus servers and HPE Synergy compute modules.

Part Number: 30-A50246BA-420

Published: May 2023

Edition: 2

NoticesNotices

The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and

services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as

constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained

herein.

Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or copying. Consistent with FAR

12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are

licensed to the U.S. Government under vendor's standard commercial license.

Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard Enterprise has no control over and is

not responsible for information outside the Hewlett Packard Enterprise website.

AcknowledgmentsAcknowledgments

Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other

countries.

Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.

Red Hat is a registered trademark of Red Hat, Inc. in the United States and other countries.

Table of contentsTable of contents
Introduction
Intelligent Provisioning
F10/Remote console features
Always On Intelligent Provisioning (AoIP)
Intelligent Provisioning operation
Navigating Intelligent Provisioning
Software installed with Intelligent Provisioning
Accessing Intelligent Provisioning
Accessing Intelligent Provisioning from the iLO web interface
Accessing Intelligent Provisioning using an iLO remote console session
F10 mode options
Selecting F10 mode to use
Initial configuration in Intelligent Provisioning
Using the First Time Setup wizard
Entering First Time Wizard settings
Re-enabling Intelligent Provisioning
Reinstalling Intelligent Provisioning
Reinstalling from an ISO image
Reinstalling from an RPM package (Linux only)
Configuring the hardware and installing an operating system
Configuring the hardware and installing an OS with Intelligent Provisioning
Server support and special characters
Source media types and installation methods supported for each OS
Select Install Source
Configure Installation Settings
Configure OS Setting
Configure Controller
Select OS drive and set partition
Configure Firmware Update
Reviewing your settings
Checking installation parameters
About RAID arrays
RAID 0
RAID 1 and RAID 1+0 (RAID 10)
RAID 5
RAID 50
RAID 6
RAID 60
Dedicated spare

Failure spare activation
Performing maintenance
Updating firmware
Determining the installed Intelligent Provisioning version
Setting Intelligent Provisioning Preferences
Downloading Active Health System data
Downloading an Active Health System log
Uploading an AHS log to AHSV
Using Deployment Settings
Creating a Deployment Settings package
Using Deployment Settings package to configure a single server
Deployment Settings actions
Using the BIOS Configuration (RBSU) utility
About iLO Configuration
Administration
Reset Options
Configuring Intelligent Storage
Creating a new array or logical drive using advanced mode
Configuring an array or logical drive
About Hardware Validation Tool
Using the hardware validation tool
One-button secure erase
Using System Erase and Reset
System Erase and Reset options
Creating a RAID configuration with SSA
Using SSA
SSA features
Accessing SSA
Configuration
Diagnose
Using the USB Key Utility
Troubleshooting
Basic troubleshooting techniques
Troubleshooting general issues
iLO log on required during Intelligent Provisioning F10 boot
Intelligent Provisioning does not launch when F10 is pressed
Intelligent Provisioning does not reimage AOIP
Accessing version information in deployment settings
A browser does not import a deployment profile correctly
Cannot create a custom partition size
Intelligent Provisioning cannot launch One-Button secure erase

One-Button secure erase is unsuccessful or reports errors
One-Button secure erase succeeds but some drives are not erased.
One-Button secure erase reports errors, but no specific details.
Troubleshooting Linux-specific issues
Assisted installation of Red Hat OS hangs
Showing "Unable to install without the usb_storage driver loaded, Aborting",when upgrade or install with rpm
Unable to install Red Hat Enterprise Linux with secure boot enabled
Troubleshooting VMware-specific issues
Server reboots during VMware Assisted installation
Websites
Support and other resources
Accessing Hewlett Packard Enterprise Support
Accessing updates
Remote support
Customer self repair
Warranty information
Regulatory information
Documentation feedback

IntroductionIntroduction

SubtopicsSubtopics

Intelligent ProvisioningIntelligent Provisioning

Software installed with Intelligent ProvisioningSoftware installed with Intelligent Provisioning

Intelligent ProvisioningIntelligent Provisioning

Intelligent Provisioning is a single-server deployment tool embedded in ProLiant servers and HPE Synergy compute modules. Intelligent

Provisioning simplifies server setup, providing a reliable and consistent way to deploy servers.

Intelligent Provisioning prepares the system for installing original, licensed vendor media and Hewlett Packard Enterprise-branded versions

of OS software. Intelligent Provisioning also prepares the system to integrate optimized server support software from the Service Pack for

ProLiant (SPP). SPP is a comprehensive systems software and firmware solution for ProLiant servers, server blades, their enclosures. The

same solution for HPE Synergy compute modules is now called SSP (Synergy Service Pack). These components are preloaded with a basic

set of firmware and OS components that are installed along with Intelligent Provisioning.

IMPORTANT:IMPORTANT:

HPE Synergy servers do not support operating system installation with Intelligent Provisioning, but they do support the

maintenance features. For more information, see "Performing Maintenance" in the Intelligent Provisioning user guide and

online help.

After the server is running, you can update the firmware to install additional components. You can also update any components that have

been outdated since the server was manufactured.

To access Intelligent Provisioning:

Press F10 from the POST screen and enter Intelligent Provisioning .

From the iLO web interface using Lifecycle Management. Lifecycle Management allows you to access Intelligent Provisioning without

rebooting your server.

NOTE:NOTE: HPE ProLiant RL3xx Gen 11 platforms do not support Intelligent Provisioning via both F10 and Lifecycle

Management.

SubtopicsSubtopics

F10/Remote console featuresF10/Remote console features

Always On Intelligent Provisioning (AoIP)Always On Intelligent Provisioning (AoIP)

Intelligent Provisioning operationIntelligent Provisioning operation

Navigating Intelligent ProvisioningNavigating Intelligent Provisioning

F10/Remote console featuresF10/Remote console features

F10/Remote console allows you to:

Access Smart Storage Administrator for disk configuration.

Perform a full set-up of Intelligent Provisioning.

F10/Remote console includes options that are not available in Always On Intelligent Provisioning.

Intelligent Provisioning 4.20 User Guide for HPE ProLiant and Synergy Gen11 Servers 6

Always On Intelligent ProvisioningAlways On Intelligent Provisioning (AoIP) (AoIP)

Always On Intelligent Provisioning allows you to:

Perform functions when the server is off.

Perform tasks when running an operating system without powering off the server.

Perform firmware updates from the HPE repository.

In the Always On Intelligent Provisioning version, the Perform MaintenancePerform Maintenance screen contains utilities that are not available in iLO. For more

information, see the iLO User Guide posted at https://www.hpe.com/support/ilo-docshttps://www.hpe.com/support/ilo-docs.

NOTE:NOTE:

To install an OS in Always On mode, extract the installation ISO on the FTP server.

Intelligent ProvisioningIntelligent Provisioning operation operation

NOTE:NOTE:

Intelligent Provisioning 4.00 and later requires iLO6 firmware version 1.10 or later.

Intelligent Provisioning includes the following components:

Critical boot drivers

Active Health System (AHS)

Erase Utility

Deployment Settings

IMPORTANT:IMPORTANT:

Although your server is preloaded with firmware and drivers, Hewlett Packard Enterprise recommends updating the

firmware upon initial setup. Also, downloading and updating the latest version of Intelligent Provisioning ensures the

latest supported features are available.

For ProLiant servers, firmware is updated using the Intelligent Provisioning Firmware Update utility.

Do not update firmware if the version you are currently running is required for compatibility.

NOTE:NOTE:

Intelligent Provisioning does not function within multihomed configurations. A multihomed host is one that is connected to

two or more networks or has two or more IP addresses.

Intelligent Provisioning provides installation help for the following operating systems:

Microsoft Windows Server

Red Hat Enterprise Linux

SUSE Linux Enterprise Server

VMware ESXi/vSphere Custom Image

Not all versions of an OS are supported. For information about specific versions of a supported operating system, see the OS Support Matrix

on the Hewlett Packard Enterprise website (https://www.hpe.com/info/ossupporthttps://www.hpe.com/info/ossupport).

Intelligent Provisioning 4.20 User Guide for HPE ProLiant and Synergy Gen11 Servers 7

Navigating Navigating Intelligent ProvisioningIntelligent Provisioning

To navigate through and modify settings in this menu-driven interface, use the navigation icons displayed at the top right-hand corner and

bottom left- and right-hand corners of the Intelligent Provisioning window.

These navigation icons are screen sensitive and are not displayed on all screens.

Software installed with Software installed with Intelligent ProvisioningIntelligent Provisioning

When a Windows system is installed using Intelligent Provisioning with Internet access, all the software applications are automatically

downloaded and installed. On other operating systems or on a Windows system without Internet access, the following applications are not

automatically installed with Intelligent Provisioning. To install the following applications, run SPP.

ProLiant Agentless Management Service (AMS)

Smart Storage Administrator (SSA)

Lights-Out Online Configuration Utility

Accessing Intelligent ProvisioningAccessing Intelligent Provisioning

SubtopicsSubtopics

Accessing Intelligent Provisioning from the iLO web interfaceAccessing Intelligent Provisioning from the iLO web interface

Accessing Intelligent Provisioning using an iLO remote console sessionAccessing Intelligent Provisioning using an iLO remote console session

Accessing Accessing Intelligent ProvisioningIntelligent Provisioning from the iLO web interface from the iLO web interface

ProcedureProcedure

1. Open a browser and enter https://<iLO host name or IP address> to log in to the iLO web interface.

2. Enter a user account name and password, and click Log In.

3. From the navigation tree, click Lifecycle ManagementLifecycle Management.

4. Navigate to the Intelligent ProvisioningIntelligent Provisioning tab and then click Always OnAlways On button.

ResultsResults

The Intelligent Provisioning web interface opens in a new browser window.

Accessing Accessing Intelligent ProvisioningIntelligent Provisioning using an iLO remote console session using an iLO remote console session

ProcedureProcedure

1. Open a browser and enter https://<iLO host name or IP address> to log in to the iLO web interface.

2. From the iLO web interface, navigate to the Remote Console & MediaRemote Console & Media page.

Intelligent Provisioning 4.20 User Guide for HPE ProLiant and Synergy Gen11 Servers 8

3. Verify that your system meets the requirements for using the remote console application you want to use.

4. Click the launch button for your selected application.

.Net Console

HTML5 Console

Alternatively, you can click an Integrated Remote Console link on the Information - iLO OverviewInformation - iLO Overview page.

5. Restart or power on the server.

The server restarts and the POST screen appears.

6. Press F10 when prompted during the server POST.

7. Select Intelligent Provisioning.

ResultsResults

When accessing Intelligent Provisioning, one of the following happens:

If you are using Intelligent Provisioning for the first time, the First Time Setup wizard will guide you through initial configuration and

registration tasks. For more information, see Using the First Time Setup wizard .

To exit Intelligent Provisioning, reboot the server by clicking the power icon at the top right of the page.

F10 mode optionsF10 mode options

When you launch F10 mode from the POST screen, you are able to use Intelligent Provisioning.

Intelligent Provisioning offer tools to provision and maintain servers.

Intelligent ProvisioningIntelligent Provisioning

Provisioning multiple servers.

Configuring multiple RAID arrays.

Users who have servers provisioned and deployed.

SubtopicsSubtopics

Selecting F10 mode to useSelecting F10 mode to use

Initial configuration in Intelligent ProvisioningInitial configuration in Intelligent Provisioning

Selecting F10 mode to useSelecting F10 mode to use

About this taskAbout this task

ProcedureProcedure

1. Boot the server.

2. On the POST screen, press

3. Enter Intelligent Provisioning, if Host Authentication is disabled in iLO. If Host Authentication is enabled, pass the credentials to use

Intelligent Provisioning.

F10

Intelligent Provisioning 4.20 User Guide for HPE ProLiant and Synergy Gen11 Servers 9

Initial configuration in Initial configuration in Intelligent ProvisioningIntelligent Provisioning

SubtopicsSubtopics

Using the First Time Setup wizardUsing the First Time Setup wizard

Re-enabling Intelligent ProvisioningRe-enabling Intelligent Provisioning

Reinstalling Intelligent ProvisioningReinstalling Intelligent Provisioning

Using the First Time Setup wizardUsing the First Time Setup wizard

About this taskAbout this task

The first time Intelligent Provisioning runs on a server, the First Time Setup wizard guides you through selecting preferences for your

system.

The first time you launch Intelligent Provisioning you get the option to select Intelligent Provisioning or the HPE Rapid Setup Software

interface.

SubtopicsSubtopics

Entering First Time Wizard settingsEntering First Time Wizard settings

About this taskAbout this task

If you do not want to use the First Time Wizard, click the Skip button.

ProcedureProcedure

1. Enter the following, or select the defaults:

Interface Language

Keyboard Language

Time Zone

Boot BIOS Mode

System Date

System Software Update

System Time

Provide anonymous usage and error feedback to help improve this product

2. Click Next.

3. Read the EULA, and then select Accept Intelligent Provisioning EULA .

4. Click Next.

5. Enter the following information:

Automatically optimize your server

Intelligent Provisioning 4.20 User Guide for HPE ProLiant and Synergy Gen11 Servers 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HPE Server Handbücher

HPE

HPE ProLiant DL80 Gen9 Handbuch

HPE

HPE StoreOnce 6500 Bedienungsanleitung

HPE

HPE ProLiant ML350 Gen10 Bedienungsanleitung

HPE

HPE ProLiant DL360 Gen11 Handbuch

HPE

HPE ProLiant DL360 Gen10 Bedienungsanleitung

HPE

HPE ProLiant ML150 Gen9 Bedienungsanleitung

HPE

HPE ProLiant DL385 Bedienungsanleitung

HPE

HPE ProLiant DL388 Gen10 Handbuch

HPE

HPE ProLiant XL230k Gen10 Handbuch

HPE

HPE ProLiant DL20 Gen10 Bedienungsanleitung

HPE

HPE SimpliVity 2600 Gen10 Produkthandbuch

HPE

HPE Apollo sx40 Handbuch

HPE

HPE ProLiant MicroServer Gen10 Bedienungsanleitung

HPE

HPE XP7 Automation Director Bedienungsanleitung

HPE

HPE ProLiant ML110 Gen10 Handbuch

HPE

HPE ProLiant XL250a Gen9 Handbuch

HPE

HPE ProLiant DL580 Gen9 Montageanleitung

HPE

HPE ProLiant ML350 Handbuch

HPE

HPE ProLiant DL385 Gen10 Bedienungsanleitung

HPE

HPE Synergy 12000 Montageanleitung

HPE

HPE ProLiant ML30 Generation9 Gebrauchsanweisung

HPE

HPE ProLiant DL385 Gen10 Plus Bedienungsanleitung

HPE

HPE ProLiant XL450 Gen10 Bedienungsanleitung

HPE

HPE Apollo k6000 Montageanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung