HPM GLLED005 Bedienungsanleitung

LED Pond Lights

Instruction Manual

Cat. GLLED005, GLLED007, GLLED008, GLLED009

1 Specifications

Cat No GLLED005, GLLED009 GLLED007 GLLED008

Description LED Mini Pond Light LED Pond Light

Power 3.5W 4.5W

Lumen output 260 lm 370 lm

Beam Angle 93˚ 67˚

Replacement globe 3.5W LED-MR16 (UPTO 20W Halogen MR16) 3.5W LED-MR16 (UPTO 35W Halogen MR16)

Housing Material / Finish Aluminium Powdercoated Black Solid Brass - Electoplated

Stainless Steel ﬁnish

Voltage 12Vac

IP rating IP68

CCT 3000K

Mounting Metal Bracket / Plastic Ground stake

Wiring connection Jaw Lock connector

Lifetime (Lamp) 25000hrs @ 25˚C

Warranty 1 yr (Excludes Globe)

2 Globe Assembly

STEP 1 Find 1x LED MR16 lamp in packaging (in a separate box).

STEP 2 Undo 4x Screws on the face of ﬁxture & remove frame with clear glass.

STEP 3 Push lamp in ﬁrmly into holder.

STEP 4 Ensure the Gasket is positioned in the step, locate the glass onto the base and

ﬁx the frame back into place. The gasket is necessary to maintain IP rating of ﬁxture.

GLLED007, GLLED008

3 Cable Layout

If your installation includes multiple lights, HPM strongly recommends that you limit individual

cable lengths to 20 metres, or use HPM heavier duty cable, otherwise lights may get progressively

dimmer towards the end of the cable (voltage drop). See section for accessories

If your installation requires a total of more than 20 metres of cable, consider running two seperate

cables from the transformer output.

It is recommended that the LED lighting does not exceed 50% of the load rating of the transformer.

Refer to section ‘Choosing a suitable transformer’ for further information

GLLED005, GLLED009

4 Installation

To connect your garden lights, follow the instructions below:

STEP 1 Place your garden lights in the approximate position you want them to be.

STEP 2 Lay out the cable where you want your lights to be located, remembering to allow sufﬁcient cable to connect to the transformer. Try to avoid laying the

cable where frequent digging may occur.

STEP 3 - Installation of a 12V Timer (if applicable)

If a 12 volt timer (HPM Cat No RGL10) is purchased, it must be positioned between

the transformer and the lights. With the power turned off, connect the wire strands,

on the end of the timer cable, into the output terminals of the transformer. Secure

ﬁrmly with a screwdriver.

STEP 4 - Installation of the transformer

Connect the cable to the transformer terminals (or timer, if applicable) by stripping

back a small amount of insulation from each wire strand (approx. 10mm). Be careful

not to damage wires. Twist wire strands to prevent loose wire escaping from terminal

and to help ensure a tight connection. Place stripped ends into screw terminals on

transformer, or timer, and secure ﬁrmly with a screwdriver.

STEP 5 First connect the garden light that will be positioned the furthest away from

the transformer.

The special connector on each light is designed to make electrical connection by

piercing the insulation cable as the two halves of the connector are pushed together. (See connection diagrams).

5 Connecting your garden lights

The special jaw lock connectors are designed to make electrical

connection by piercing the insulation cable as the jaw lock

connecter is attached.

STEP 1 Lay the cable ﬂat on one half of the connector as shown.

STEP 2 Lay the other half of the connector on top of the cable,

upside down, taking care to align the pins into their matchng

holes on the other half. Push together firmly until they lock.

Check that the two halves are pushed tightly together. (This will

cause the spikes to deeply pierce into the copper centre of the

cable and make a solid electrical connection).

STEP 3 Plug the transformer into the powerpoint and check

whether the furthest positioned garden light operates. (If it doesn’t light up, refer to ‘Troubleshooting’ section). If light does light up, switch off the transformer

and proceed to connect all the other garden lights using the steps above.

To check each light connection is secure, first turn the transormer on from the powerpoint, then gently wiggle the cable and connector.

(This is perfectly safe - the voltage at this point is very low). If the light flickers, the connection is not ﬁrm enough and should be re-connected

(repeat ‘Connecting your gaden lights’ Steps 1-2).

6 Setup

STEP 1 Switch off the transformer from the powerpoint.

STEP 2 If you wish to cover the cable in the ground, dig a narrow channel, about 100mm deep (just deep enough to hide the cable).

STEP 3 Lay the cable at the bottom of the channel, or fasten the cable to the wall or step using appropriate ﬁxings.

If your cable will be covered in the ground, we recommend, at this point, that you observe the overall lighting effectiveness in the dark before covering the channel.

7 Globe replacement

To replace lamp follow instructions for Globe Assembly.

Note: If lamps do not turn ON or ﬂicker when powered ON, repeat steps for Globe Assembly to see if there is a loose contact.

Transformer Load rating (incandescent lighting) Load rating (LED lighting)

RGLTR60 60W 30W

RGLTR105 105W 50W

RGLTR220 200W 100W

RGLTR400 400W 200W

RGLPCTAW20 10W 5W

8 Choosing a suitable transformer

The total wattage of your LED garden lights must not be greater than ½ of the rating of the transformer.

For example if the RGLTR60 60W transformer is used then adding up the wattages of each LED light (e.g 4 x 6W = 24W) should not exceed the 30W max load.

Note - Not for submersion in water greater than 0.5 metres in depth. Do not use in salt water or water treated with chlorine.

08_2017 LE10388AAA HPML1701

Warranty

Legrand warrants this product for a period of 1 year from the date of purchase when used

in accordance with these instructions and considering the disclaimers listed herein.

These goods come with guarantees that cannot be excluded under the Australian and

New Zealand Consumer Laws. You are entitled to a replacement or a refund for a major

failure and for compensation for any other reasonably foreseeable loss or damage. You

are also entitled to have the goods repaired if the goods fail to be of acceptable quality

and the failure does not amount to a major failure.

See the Warranty card enclosed with this product for further details.

Customer Service

For all Customer Service and Technical Support

please call Monday to Friday during business hours.

Legrand Australia

1300 369 777

www.hpm.com.au

Legrand New Zealand

0800 476 009

www.hpm.co.nz

ABN: 31 000 102 661

9 Accessories

Outdoor Garden Cables:

RGL8 (2-core 1.3mm² 10m length)

RGL9 (2-core 1.3mm² 20m length)

RGLCL21/20 (2-core 2.1mm² 20m length)

RGLCL21/30 (2-core 2.1mm² 30m length)

RGLCL33/30 (2-core 3.3mm² 30m length)

RGLHSC15 (2-core 0.5mm² 15m length)

Connectors:

CDGLCC4 (pack of 4 cable connector)

Transformers:

RGLTR60

RGLTR105

RGLTR220

RGLTR400

RGLPCTAW20

Sensor & Timers

(Compatible only with 60VA -200VA transformers)

RGL10 (200W sunset timer)

DGLS150 (150W dusk to dawn sensor)

10 Troubleshooting

11 Maintenance

To prolong the life of your Gardenlights HPM recommends the following:

• Install away from salty or corrosive environments

• Install away from highly fertilised areas

• Do not sudmerse in treated water such as chlorinated pools

To keep your lights looking new, keep lenses free of dust and residue by wiping occasionally with a dry cloth, or warm soapy water if necessary.

If using soapy water, ensure that you thoroughly dry your light after cleaning.

Problem Possible Solution

The powerpoint is turned on,

but the lights are off.

1. The connections at the base of transformer may be loose. Tighten firmly

2. There is no power to the powerpoint, (Consult an electrician).

3. You may not have pierced the cable well enough with the metal spikes in the jaw-lock connectors. Check that

the cable insulation has been fully pierced by the spikes.

Some lights are working, one or

more are not.

1. If one or more of the lights are not working, ﬁrst check the connection of the light to the cable (See

‘Connecting your garden lights’ section). If this is ﬁrm, check the globes by putting the ‘non-working’ globes

into a working ﬁtting. Replace unserviceable globes, (If applicable).

One or more lights flicker. 1. The connection to the light is loose. (See ‘Connecting your garden lights’ section).

2. The globe is loose. Push in ﬁrmly, (Watch out that globe is not hot). (HPM recommends paper or cloth be used

to handle the globe).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HPM Landschaftsbeleuchtung Handbücher

HPM

HPM GLLED004 Bedienungsanleitung

Beliebte Landschaftsbeleuchtung Handbücher anderer Marken

Intex

Intex SL1006 Bedienungsanleitung

LED Group

LED Group ROBUS R2IN13W Bedienungsanleitung

Patriot Lighting

Patriot Lighting 343-1484 Bedienungsanleitung

Hess

Hess SERA G: SERA S Bedienungsanleitung

LIGMAN

LIGMAN JET 44 Bedienungsanleitung

LIGMAN

LIGMAN MALTA 1 Bedienungsanleitung

Cooper Lighting

Cooper Lighting MCGRAW-EDISON WBG Bedienungsanleitung

Cooper Lighting

Cooper Lighting Invue 42 - 175W Bedienungsanleitung

Saxby Lighting

Saxby Lighting Islay 68784 Handbuch

LIGMAN

LIGMAN EU-10016-3 Bedienungsanleitung

Cooper Lighting

Cooper Lighting McGraw-Edison ZD Credenza Bedienungsanleitung

LIGMAN

LIGMAN KI-60475 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Generation CLB25MWW5C373 Bedienungsanleitung

Malibu Boats

Malibu Boats CL905K Bedienungsanleitung

LIGMAN

LIGMAN NYB-30161 Bedienungsanleitung

LIGMAN

LIGMAN SI-80021 Bedienungsanleitung

Volt

Volt 2-in-1 Tiki-Brass Torch Light Bedienungsanleitung

Malibu Boats

Malibu Boats CM110P Bedienungsanleitung