Huawei SmartAX MA5811S-AE08 Bedienungsanleitung

HUAWEI TECHNOLOGIES CO., LTD.

SmartAX MA5811S-AE08 Multi-service Access Module

V800R017C10

Installation Guide

Issue: 01

Date: 2016-09-14

1. Precautions 3

2. Check Tools and Meters 4

3. Appearance and Structure 5

4. Installing the Chassis 7

a. Installing the MA5811S-AE08 on a pole 7

b. Installing the MA5811S-AE08 on the wall 9

5. Routing the Cables 11

a. Routing a PGND Cable 11

b. Connecting a Subscriber Cable 12

c. Routing an Optical Fiber 17

6. Checking the Installation 19

7. Checking Device Running used backup power 20

8. Checking Upstream Port Optical Power 21

9. Checking Device Running 22

10. FAQs for Installation 23

Contents

Electrostatic Discharge

Before touching the device or holding the boards and IC chips, wear the ESD gloves or the ESD wrist

strap (Ensure that the other end of the ESD wrist strap is well grounded) to prevent the electrostatic

discharge of the human body from damaging the sensitive components.

Attaching Labels or Tags

•After routing the cable, attach the label or fasten the tag to the cable, and 20 mm away from the

connector.

•When the signal cable is placed vertically, the label should point towards the right. When the cable is

placed horizontally, the label should point downwards. After bundling the cables, the completed

identification plate should be visible on the top of the cable in the horizontal cabling, or on the right

side of the cable in the vertical cabling. Make sure that the label points outwards.

ESD gloves ESD wrist strap

Indoor climbing work should ensure that the ladder (or other load bearing equipment) stable,

ascending the operation of the operator, tools and materials should be properly disposed so as not

to fall, ascending operation during its operation area part of the ground personnel should wear

safety helmet or evacuate; operators should wear safety rope, clothing, shoes, a tool into the tool

bag, attention when people climb ahead of the tool, tool ahead of people evacuation.

Hardware installation operation of all should be under the condition without electricity, if need to

have charged equipment operation, operation personnel in addition to tools, clothes do not have

other exposed metal objects, and tools and metal parts of tape is wrapped around the insulation,

the operator must wear insulated gloves.

Safety Precautions

reserved.

Precautions

Before you begin, get the following tools ready.

Marker Flat-head

screwdriver Phillips

screwdriver Diagonal

pliers

Cable cutter ESD gloves Multimeter Optical power

meter

Paper knife Measuring tape

Check Tools and Meters

Crimping tool 5# (M6) wrench

Impact tool

(HUAWEI-JPX)

Hammer drillLocking pliers

3# (M4) wrench

130 mm

Appearance and Structure

Appearance

Support for the

terminal block

Internal Structure (without terminal block)

Ground point Upstream optical port

5 6 8

1 2 3 4

5 6 7

Maintenance serial port

PGND cable entrance Optical fiber entrance

8Subscriber cable entrance

330 mm

230 mm

Reserved

Appearance and Structure

Support for the

terminal block

Internal Structure(with terminal block)

Ground point Upstream optical port

5 6 8

1 2 3 4

5 6 7

Maintenance serial port

PGND cable entrance Optical fiber entrance

8Subscriber cable entrance

Reserved

Subscriber cable assembly

Subscriber cable

connector

Terminal block

Installing the Chassis

Installing MA5811S-AE08 on a Pole

Insert hose clamps into the mounting bracket.

Use a hex key to fix the mounting bracket onto the pole.

Trim excess hose clamps off.

5# (M6) wrench

Install the MA5811S-AE08 onto the mounting bracket.

Installing the Chassis

Installing MA5811S-AE08 on a Pole

5Use a Phillips screwdriver to fix the screws in the bottom of the mounting bracket.

Wrap the clipped hose clamp using insulation tapes.

Coiling the excess hose clamp on the pole and binding it using a cable tie is recommended for

convenience of follow-up migration.

> 180 mm

Place the MA5811S-AE08 separate mounting bracket against the wall, verify that the mounting

bracket is horizontally placed, and mark anchor points.

Installing the Chassis

Installing MA5811S-AE08 on the wall

Hammer drill

Maker

Drill holes on the wall according to marked installation points and Install M6 x 60 expansion bolts.

(hole diameter: 8.5 mm; hole depth: 45 mm to 55 mm)

Nut

Spring washer

Expansion sleeve

Flat washer

Bolt

Installing the Chassis

Installing MA5811S-AE08 on the wall

Mount the MA5811S-AE08 to the mounting kits and fasten the screws at the bottom of the

mounting kits to complete the installation.

Install mounting kits into the wall.

Bottom view

Note:

Theoretically, the MA5811S-AE08 can be reversely installed.

However, it can only be reversely installed indoors without any

water leakage. To reversely install the MA5811S-AE08, use the

M4 wrench to remove its mounting kits as shown in the right figure

and then reversely install it.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Huawei Steuereinheit Handbücher

Huawei

Huawei MU609T Bedienungsanleitung

Huawei

Huawei ME309-562 Montageanleitung

Huawei

Huawei MU709Gs-8 Bedienungsanleitung

Huawei

Huawei VP9660 Bedienungsanleitung

Huawei

Huawei ME909s-120 Montageanleitung

Huawei

Huawei Atool Bedienungsanleitung

Huawei

Huawei UPS5000-E-400K-SMS Bedienungsanleitung

Huawei

Huawei RRU3269 Bedienungsanleitung

Huawei

Huawei EDFA0820-D Betriebsanleitung

Huawei

Huawei ME909 Series Montageanleitung

Huawei

Huawei SmartLogger2000 series Bedienungsanleitung

Huawei

Huawei MU609 Handbuch

Huawei

Huawei SmartLogger2000-10-C-JP Bedienungsanleitung

Huawei

Huawei ME909u-521 Montageanleitung

Huawei

Huawei MU509-b Benutzerhandbuch

Huawei

Huawei ME909u-523 Montageanleitung

Huawei

Huawei MU736 HSPA+ M.2 Montageanleitung

Huawei

Huawei G530 V2 Kurzanleitung

Huawei

Huawei MU609 Benutzerhandbuch

Huawei

Huawei MU509 Series Bedienungsanleitung

Huawei

Huawei SmartLi-ESM-24020P1 Bedienungsanleitung

Huawei

Huawei MU709s-2 Montageanleitung

Huawei

Huawei EM770V Bedienungsanleitung

Huawei

Huawei UPS5000-E Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung