Hubbell RDS50Z Bedienungsanleitung

Installation Instruction for new

construction of a Door Jamb Switch

Kit (RDS50Z) Normally Closed

Door open lights ON, Door closed

lights are OFF.

3A, 125 Vac. 4.6 Cu Inch.

NOTICE: For installation by a qualified electrician in accordance with national and local electrical codes and the

following instructions.

CAUTION: RISK OF ELECTRICAL SHOCK. Disconnect power before installing.

CAUTION: Make sure that you follow local Electrical rules and regulations. If unsure, consult a qualified electrician.

NOTE: Do not install on a Metal door frame

NOTE: Use Copper Conductors only.

1) Create suitable cable entry in Door Frame.

2) Make an opening in Door Jam to suit Junction Box. (See

Fig. 2 for dimensions of Box). Create recess for Box

Ears to ensure Switch Plate is flush to door jamb when

installed.

3) Remove a knock out in Junction Box to accommodate

cable entry.

4) Insert cable through knock out and secure to box with

approved connector (not provided).

5) Fasten box to door jamb with 4 wood screws

(provided).

6) Connect GREEN/ BARE (ground) wire to ground screw

in back of junction box, connect Line and Load wires to

switch pig tail wires following national and local

electrical codes Use Fig. 1 for guidance.

7) Adjust shaft to proper depth on switch plate using

locknuts (provided) at the back and front of the switch

assy’ for contact with round kicker plate .

8) Using 2 short screws (provided), fasten the switch

plate to the box.

9) With power ON, Open and close door to verify proper

operation of the switch and adjust switch depth

accordingly.

10) Once proper positioning is established, install the

round kicker plate on the door side to face the switch

button, by fastening with the wood screw (provided).

11) Installation is complete.

Fig. 2 Fig. 3

Supply runs directly to the fixture

Inhaltsverzeichnis

Andere Hubbell Schalten Handbücher

Hubbell

Hubbell Type AR Bedienungsanleitung

Hubbell

Hubbell Killark VWSQ Series Bedienungsanleitung

Hubbell

Hubbell MOTORQUICK Bedienungsanleitung

Hubbell

Hubbell Euclid PBP Pendant Bedienungsanleitung

Hubbell

Hubbell H-MOSS AP Bedienungsanleitung

Hubbell

Hubbell 2243 Bedienungsanleitung

Hubbell

Hubbell CXSW Bedienungsanleitung

Hubbell

Hubbell 4211 Gebrauchs- und Pflegehandbuch

Hubbell

Hubbell C5027 Handbuch

Hubbell

Hubbell 58-GC5026 Handbuch

Hubbell

Hubbell Reversing Drum Controller 58-GJ2 Handbuch

Hubbell

Hubbell CIRCUIT-LOCK Series Konfigurationshandbuch

Hubbell

Hubbell Furnas Brand Series 54 Bedienungsanleitung

Hubbell

Hubbell Circuit-Lock Bedienungsanleitung

Hubbell

Hubbell SNAPConnect Series Bedienungsanleitung

Hubbell

Hubbell 2210 Bedienungsanleitung

Hubbell

Hubbell 4310 Handbuch

Hubbell

Hubbell CIRCUIT-LOCK Bedienungsanleitung

Hubbell

Hubbell Euclid 4220 Bedienungsanleitung

Hubbell

Hubbell iDevices IDEVZ01DW Bedienungsanleitung

Hubbell

Hubbell M3 Programmierhandbuch

Hubbell

Hubbell LUXSTATSW1 Bedienungsanleitung

Hubbell

Hubbell 2200 Bedienungsanleitung

Hubbell

Hubbell EUCLID Montage- und Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung