Human Touch AcuTouch 6.0 Bedienungsanleitung
AcuTouch®6.0
Human Touch®Massage Chair
troubleshooting guide
©2013 Human Touch, LLC. All rights reserved.
September 13, 2013
AcuTouch 6.0 Troubleshooting Guide 1
AcuTouch 6.0 Troubleshooting
This Troubleshooting Guide walks you step-by-step through the
diagnosis of AcuTouch 6.0 customer problems. It is important to follow
these steps carefully, to ensure that the problem is diagnosed
correctly, and therefore the appropriate repair action is taken.
Getting Started
1. Turn the power switch on the back of the chair base to Off, wait
approximately five seconds, then turn it back On.
2. Verify that the backrest massage mechanism and the foot and calf
massager paddles move when you power on the chair. If they do
not, see "Power" on page 2.
3. Wait 30 seconds while a system check is performed, then verify
that the problem still exists.
4. If the problem still exists, choose from the following issues:,
To Troubleshoot This
Issue: Do the following:
My remote control is
not working properly
• If the remote screen does not display any
text, replace the remote.
• If the remote screen displays normal text but
you cannot activate any of the functions,
replace the massage mechanism.
My backrest is not
massaging properly
Using the remote control, select Action
Settings, then scroll through the options to
verify that the function you want to use is not
turned off.
Replace the massage mechanism.
2AcuTouch 6.0 Troubleshooting Guide
Power
Step 1: Check the power cord
1. Verify that the power cord connection to the chair’s power panel is
secure and that the cord is not damaged.
2. If the power cord is damaged, replace the power panel.
Step 2: Check the wall outlet
1. Plug a known working device, such as a lamp, into the AC outlet into
which the chair is plugged.
2. If the device does not work (is not receiving power), the AC outlet is
most likely not working. Plug the chair into a different AC outlet to
verify that it receives power.
My seat, shoulder, or
arm air massage is not
working properly
Using the remote control, select Action
Settings, then scroll through the options to
verify that the function you want to use is not
turned off.
Replace the chair.
My backrest won’t
recline/incline
Make sure you are pressing and holding the
recline/incline button for at least five seconds; it
can take several seconds to activate.
See "Backrest Recline/Incline" on page 3.
My foot and calf
massager is not
massagingproperlybut
I can still deploy/
retract it.
Using the remote control, select Action
Settings, then scroll through the options to
verify that the function you want to use is not
turned off.
Replace the foot-and-calf massager.
My foot and calf
massager won’t
massage, and I can
NOT retract it.
Replace the chair.
My foot and calf
massager massages
but won’t raise/lower
See "Foot and Calf Massager
Deploy/Retract" on page 3.
My foot and calf
massager extension
isn’t working
Replace the footrest extension lever.
To Troubleshoot This
Issue: Do the following:
AcuTouch 6.0 Troubleshooting Guide 3
Step 3: If the chair is still not receiving power, replace the
main PCB board
If this still does not solve the problem, replace the chair.
Backrest Recline/Incline
The remote beeps once when Recline/Incline buttons are
pushed:
If you hear a single beep when you push the Recline and Incline
buttons, it means the backrest actuator is receiving power. Therefore the
actuator itself is not working properly. Replace the backrest actuator.
The remote beeps twice when Recline/Incline buttons
pushed:
If the backrest is in a fully inclined position and you hear two beeps
when you push the Recline button, it means the safety sensor has likely
failed.
1. Make sure that nothing is pressing on the safety sensor.
2. Tap the safety sensor with your foot to ensure that it didn’t get stuck
during shipping.
3. If the problem still exists, replace the safety sensor cover.
Foot and Calf Massager Deploy/Retract
The foot and calf massager will not retract the last few
inches into the chair base
Make sure the massager is not in the extended-length position (it must
be returned to default position before retracting it).
The foot and calf massager will not raise or lower at all,
and the remote beeps when you push the legs up and legs
down buttons on the controller.
Replace the foot-and-calf massager actuator.
If replacing the actuator does not solve the problem, replace the main
PCB.
Human Touch, LLC
3030 Walnut Ave.
Long Beach, CA 90807
humantouch.com
Inhaltsverzeichnis
Andere Human Touch Massagegerät Handbücher
Human Touch
Human Touch ht 149 Bedienungsanleitung
Human Touch
Human Touch HT-Navitas Sleep Ascent Series Bedienungsanleitung
Human Touch
Human Touch PC-095 Bedienungsanleitung
Human Touch
Human Touch Ht 136 Bedienungsanleitung
Human Touch
Human Touch ht103 Bedienungsanleitung
Human Touch
Human Touch CirQlation Pro Bedienungsanleitung
Human Touch
Human Touch HT-102 Bedienungsanleitung
Human Touch
Human Touch HT-270 Bedienungsanleitung
Human Touch
Human Touch HT-9200 Bedienungsanleitung
Human Touch
Human Touch IJOY HT-2720 Bedienungsanleitung
Human Touch
Human Touch iJoy-130 Betriebsanleitung
Human Touch
Human Touch PC6 Bedienungsanleitung
Human Touch
Human Touch ZeroG Volito Bedienungsanleitung
Human Touch
Human Touch HT-Reflex 2 Bedienungsanleitung
Human Touch
Human Touch HT-270 Bedienungsanleitung
Human Touch
Human Touch Cirqlation HT-1360 Bedienungsanleitung
Human Touch
Human Touch pc 085 Bedienungsanleitung
Human Touch
Human Touch Ht 136 Bedienungsanleitung
Human Touch
Human Touch Perfect Chair PROZero PC8500 Bedienungsanleitung
Human Touch
Human Touch iJoy-100 Bedienungsanleitung
