Humboldt HM-5030.3F Bedienungsanleitung

product manual 03.23

Master Loader Load Frame

HM-5030.3F

Quick Start Guide 4

Unpacking

Installation and Equipment Setup 4

Electrical Connections 4

Power Switch 4

Instrumentation Connections and Setup 5

HM-5030 Rear Instrumentation Panel 5

Network 5

USB Power 5

Instrument Inputs 5

Initial Set-up — Calibration 7

Calibration Input Screen 9

Units 10

Value 10

Export Calibration via USB 11

Initial Set Up — Date/Time 11

Date 12

Time 12

Clock Style 12

Clock 12

Initial Set Up — Display 13

Brightness 13

Dim Display 13

Turn Display Off 14

Preferences 14

Initial Set Up — Preferences 14

Preferences – General Tab 14

Logger ID 15

Sound 15

Automatically Update System 15

Update Check Frequency 15

Preferences – System Units Tab 15

Ambient Temperature 15

Motor Speed Unit 16

Stress Control Unit 16

Preferences – Specimen Parameters Tab16

Specimen Height 16

Specimen Diameter 16

Specimen Width 16

Preferences – Storage Tab 16

Test Storage Limit 17

Recycled Tests 17

Test Templates 17

Initial Set Up — Network 17

Network Settings Screen 19

DHCP 19

IP Information 19

Local Status 19

Internet Status 19

Initial Set Up — Information 19

Initial Set Up —

System Information 20

Firmware Version 20

IP Information 20

Local Status 20

Internet Status 20

Memory 20

Factory Screen 20

Export Log File 20

Initial Set Up — Contact 21

Contact Information 21

Initial Set Up — Update 22

Update from USB 22

Check for Update 24

Update Details 24

Download Updates 24

Equipment Setup 25

Installation and Equipment Setup 26

Electrical Connections 26

Power Switch 26

Instrumentation Connections and Setup 26

Rear Instrumentation Panel 26

Network 27

USB Power 27

Instrument Inputs 27

Instrumentation Setup 28

Typical Setups 29

Third-Party Instrumentation 30

Calibration of Instrumentation 30

How to Perform a Calibration 30

Calibration Input Screen 32

Units 32

Value 33

Performing a New Calibration 33

Test Setup 41

Test Setup Wizard – Select Test Type 42

Test Setup Wizard – Template 43

Test Setup Wizard – Select Test Inputs 43

Test Setup Wizard – Select Motor Condition 44

Test Setup Wizard – Logging Condition 46

Interval Logging 46

Linear Time Interval 47

Interval Logging Table 48

Elapsed Time Table 50

Test Setup Wizard – Stop Condition 52

Test Setup Wizard – Graph Options 53

Test Setup Wizard – Start Options 53

Test Setup Wizard – Start 55

Tests– Current Tests Tab 56

Tests– Previous Tests Tab 59

Specications 62

General Warnings 63

Warranty 63

Manufacturers Rights & Responsibilities 64

CONTENTS

QUICK START GUIDE

Unpacking

Initial inspection should include checking for physical dam-

age during shipping and obvious external damage to the

product.

Package contents are dened by your packing list. Each

Load Frame is congured according to customer specica-

tions. In your inspection, make certain that the contents of

your shipment match the documentation provided by your

packing list.

Place unit on a at, smooth surface and use leveling feet

(supplied) and a bubble level to ensure that the unit is level

side-to-side and back-to-front.

Installation and Equipment Setup

Electrical Connections

The HM-5030 is equipped with an internal digital switching

power supply, which allows it to be used with most power

congurations throughout the world. The unit is supplied

with an IEC electrical cord with a standard 110V plug.

The HM-5030 arrives ready for operation. Attach the sup-

plied IEC electrical cord to the machine and plug into a

standard wall receptacle for use in the United States. For

locations other than the U.S., replace the supplied electrical

cord with an IEC cord that has the correct plug for your ap-

plication. The supplied cord can also be used by cutting the

standard plug from the cord and attaching the correct plug.

Power Switch

The Power Switch is located on the left side of the back of

the machine, above the electrical cord inlet. The Fuse Com-

partment is located between the electrical cord inlet and the

Power Switch. The HM-5030 uses a 10 amp fuse. To begin

operation, attach the supplied electrical cord, plug it in and

press the Power Switch.

Fig. 1 Power Switch

Fuse Compartment

QUICK START GUIDE

Instrumentation Connections and Setup

HM-5030 Rear Instrumentation Panel

Above is a photo of the rear instrumentation panel of the HM-

5030.

Network (1)

Ethernet input for connecting machine to a local area net-

work (LAN) and/or the internet.

USB Power (2)

The USB Power port is used for powering a wireless access

appliance for those who want to use a wireless LAN setup.

Instrument Inputs (3)

The panel features four (4) inputs for connecting instrumentation

to the machine. Each input represents a separate channel. If you

have purchased instrumentation from Humboldt with your HM-

5030, it has been assigned to a specic channel and calibrated. In-

strumentation will have a numbered tag attached to it and should

be plugged into the corresponding input on the machine.

QUICK START GUIDE

Once you have installed the instrumentation into the correct

inputs, your rear panel should look like this if you are using

all four inputs.

Below are photos of an instrumentation input and the in-

strumentation plug. Install the plugs into the inputs by lining

up the guide at the bottom of the plug with the slot at the

bottom of the input.

Instrumentation Input Instrumentation Plug

If you purchased multiple load cells and/or transducers with

your machine, they will either be mounted and calibrated, or

in the case of more than four (4) load cells/transducers, cali-

brated and assigned to a specic input, but not mounted.

Additional load cells/transducers will be marked to indicate

what input channel was used in their calibration. These

load cells/transducers should be connected to the indicat-

ed channels when desired for use, however you will have

to import the correct calibration information to that input

before use. This information can be found on a USB thumb-

QUICK START GUIDE

drive that was included with your machine. Refer to the Equip-

ment Setup section of this manual, page 25 for additional

information and instructions on how to accomplish this.

Third-party instrumentation, which is compatible, can also

be used with the HM-5030. If you plan to use third-party

load cells and/or transducers, please refer to the Equipment

Setup section of this manual, page 30 for instructions.

Remember, if you purchased Humboldt instrumentation

with your HM-5030, it is already calibrated and assigned

to a channel and will not need calibration, however you

shouldconrmthattheinstrumentationhasbeensetup

and calibrated. If you are using 3rd-party instrumenta-

tion, go to the Equipment Setup section for calibration

instructions.

When your HM-5030 is rst turned on, the screen below will

appear.

DO NOT RECALIBRATE!

From this screen, to conrm your machine instrumentation has

been calibrated, navigate to the Calibration section by clicking

the Menu icon in the top left corner of the screen (1). When you

click on this button, you will see a drop-down menu appear,

see below.

Initial Set Up

QUICK START GUIDE

Navigate to the bottom of this drop-down menu and click

on System Settings (1). You will see the following screen.

Click on the Calibration tab in the top left corner (2). You will

see the following screen.

Initial Set Up — Calibration

QUICK START GUIDE

Calibration Input Screen

The Calibration Input Screen (above) is used to monitor and

calibrate instrumentation and assign them to specic chan-

nels of the HM-5030. The Calibration Input Screen provides

a summary of the calibration status of each channel. At this

time, verify the calibration information.

A green box at the left of a channel indicates that the chan-

nel has instrumentation assigned to it and that it is calibrat-

ed and ready for use (1).

Each channel has a “Limits On” check box. Use the Limits

On to keep the machine from exceeding the sensor limits

of the instrumentation. By selecting this option, before the

test can exceed the limits of the sensors, all tests will stop

QUICK START GUIDE

The screen above shows a typical calibration setup. In this

example, the HM-5030 has been set up for a standard

Consolidated Drained or Undrained Triaxial setup. Input One

has been set up for the load cell with a value of 0.000 to

running and the motor will stop to avoid damaging con-

nected instrumentation.

Note: An input cannot be calibrated during testing.

Units (2)

In this eld, a calibrated instrument will display the units

that were chosen for use at the time of calibration. This eld

can also be used to automatically toggle conversion of units

between lb.-in. and SI units if the need arises.

Value (3)

This eld displays the current calibration value. This val-

ue should already be set with 3 decimal point accuracy . If

the instrument is not calibrated, the unit will read “N/A.” To

change the numbers of decimels shown, click on the eld

and the following window will appear. Fill in the number of

decimal points desired (1).

Inhaltsverzeichnis

Andere Humboldt Datenlogger Handbücher

Humboldt

Humboldt HM-5320.3F Bedienungsanleitung

Beliebte Datenlogger Handbücher anderer Marken

TESTO

TESTO 176 Bedienungsanleitung

HT Italia

HT Italia XL421 Bedienungsanleitung

HBM

HBM SOMAT XR CX22B-R Bedienungsanleitung

Agtrix

Agtrix 380i Bedienungsanleitung

Hobo

Hobo H8 Pro Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech PCI2320 Bedienungsanleitung

Athena

Athena GET SL1 Bedienungsanleitung

Motec Systems

Motec Systems C185 Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech USB2832 Bedienungsanleitung

Rotronic

Rotronic HygroLog HL20 Bedienungsanleitung

MRC

MRC DW-6092 Bedienungsanleitung

Racelogic

Racelogic VBOX LapTimer Bedienungsanleitung

Edu-Logger

Edu-Logger 900-240 Bedienungsanleitung

Elma

Elma DT173 Bedienungsanleitung

MadgeTech

MadgeTech PRTemp140 Technisches Datenblatt

Comet

Comet U0121M Bedienungsanleitung

pico Technology

pico Technology PT-104 Bedienungsanleitung

Soil Instruments

Soil Instruments GTecLink Bedienungsanleitung