Humminbird 700 series Bedienungsanleitung

531906-1E _B

Et ernet Networking

Installation & Operations Manual

Et ernet Networking

Installation & Operations Manual

GPS Unit 1

Unit 2

HUMMINBIRD®

ETHERNET

T ank You!

Thank you for choosing Humminbird®, America's #1 name in Fishfinders.

Humminbird® has built its reputation by designing and manufacturing

top-quality, thoroughly reliable marine equipment. Your Humminbird®

accessory is designed for trouble-free use in even the harshest marine

environment. In the unlikely event that your Humminbird® accessory does

require repairs, we offer an exclusive Service Policy - free of charge during the

first year after purchase, and available at a reasonable rate after the one-year

period. For complete details, see the separate warranty card included with

your accessory. We encourage you to read this operations manual carefully in

order to get full benefit from all the features and applications of your

Humminbird® product.

WARNING! This device should not be used as a navigational aid to prevent collision,

grounding, boat damage, or personal injury. When the boat is moving, water depth

may change too quickly to allow time for you to react. Always operate the boat at

very slow speeds if you suspect shallow water or submerged objects.

WARNING! The electronic chart in your Humminbird® unit is an aid to navigation

designed to facilitate the use of authorized government charts, not to replace them.

Only official government charts and notices to mariners contain all of the current

information needed for the safety of navigation, and the captain is responsible for

their prudent use.

WARNING! Disassembly and repair of this electronic unit should only be performed

by authorized service personnel. Any modification of the serial number or attempt to

repair the original equipment or accessories by unauthorized individuals will void the

warranty.

WARNING! This product contains chemicals known to the State of California to

cause cancer and/or reproductive harm.

NOTE: Some features discussed in this manual require a separate purchase, and

some features are only available on international models. Every effort has been made

to clearly identify those features. Please read the manual carefully in order to

understand the full capabilities of your model.

NOTE: The Ethernet accessory is compatible with many Humminbird® models,

and every effort has been made to note the differences between the models and

functions throughout this manual. The illustrations in this manual may look

different than your display, but your model will operate in a similar way.

Table of Contents

iii

Introduction 1

1. Installing an Ethernet Connection 2

2. Powering On 7

3. Configuring the Ethernet etwork 8

Configuration Overview 8

Network Menu Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Customize the Unit ame 11

Open the etwork Source Setup Dialog Box 12

Sonar Source Overview 13

Select a Sonar Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Change the Sonar Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Temperature Source Overview 17

Select a Temperature Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Change the Temperature Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

GPS and Sharing Waypoints Overview 23

Select a PS Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Change the PS Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Share Waypoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Restore Defaults (Setup Menu Tab) 28

Table of Contents

Troubleshooting 29

Fishing System Doesn’t Power Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Fishing System Defaults to Simulator with a Transducer Attached. . . . . . . . . 30

Humminbird® Accessories 31

Introduction

This manual will guide you through the following network setup instructions:

1. Connect two Humminbird® units together

2. Power On

3. Configure your Humminbird® Ethernet etwork

4. Share Waypoints

Alarms, navigation, sonar data, and the menu system are all affected

by the Ethernet network settings. We encourage you to read this

manual completely so that you may understand the full capabilities of

your Humminbird® Ethernet network.

1Introduction

1. Installing an Et ernet Connection

If your Humminbird® control head has a built-in Ethernet connector, the unit

can be connected to the Ethernet network. When you connect the units

together, data is shared between the two units.

Before you start, please note that the Ethernet network installation has the

following requirements:

•Update Software: If your network includes a legacy Humminbird®

model, download the latest software update from your account at

humminbird. Legacy models include 858c, 898c SI, 998c SI, 958c, and

1100 Series™ units.

•Install the control heads and sources ( PS, transducers, temp/speed

accessories, etc.) for your Fishing System. See the equipment installation

guides for details.

•Purchase Ethernet Connection Cables (separate purchase required):

Your network configuration will determine which Humminbird®

connection cables you will need to purchase to connect the control

heads to the network (see the Ethernet Cable Information table).

Installation

NOTE: The AS EC [length E cable is available in a variety of lengths. T

Connect the Control Heads

1. Confirm that the control heads are powered off.

2. To install the Ethernet cables, see the connection information for

your network configuration as follows:

• Two 700 Series™ Units: see Section A.

• One 700 Series™ Unit & One 800/900/1100 Series™ Unit:

see Section B.

• Two 800, 900, or 1100 Series™ Units: see Section C.

NOTE: You may need to consult your control head installation guide for details.

NOTE: The AS EC [length]E cable is available in a variety of lengths. The following

instructions use AS EC 10E, but your cable part number may be different.

Et ernet Cable Information

(2) 700 Series™ Units

(1) 700 Series™ Unit &

(1) 800/900/1100 Series™ Unit

(2) 800, 900, or 1100 Series™ Units

Control Heads

(1) AS EC [length]E

(1) AS EC QDE & (1) AS EC [length]E

(2) AS EC QDE & (1) AS EC [length]E

Required Cables

3Installation

A. Two 700 Series™ Units

1. Insert the AS EC QDE Ethernet cable connector into the

Ethernet slot on the 700 Series™cable collector. Repeat this

step for the second AS EC QDE cable.

NOTE: The 700 Series™control head uses a cable collector for the uick

Disconnect Mount and the In-Dash Mount. See your control head installation

guide for details.

2. Connect the AS EC 10E to each round connector on the

AS EC QDE cables.

3. Hand-tighten the screw nut(s) on each cable to secure the

connection. The connectors are keyed to prevent incorrect

installation, so be careful not to force the connectors.

B. One 700 Series™ Unit & One 800/900/1100 Series™ Unit

1. Insert the AS EC QDE Ethernet cable connector into the

Ethernet slot on the 700 Series™ cable collector.

NOTE: The 700 Series™control head uses a cable collector for the uick

Disconnect Mount or the In-Dash Mount. See your control head installation guide

for details.

2. Insert one end of the AS EC 10E cable into the Ethernet port on

the back of the 800/900/1100 Series™ control head. The

connectors are keyed to prevent incorrect installation, so be

careful not to force the connectors into the port.

700 Series™Quick Disconnect Mount Cable Collector

Ethernet

Installation

3. Connect the AS EC QDE cable connector to the AS EC 10E cable

connector.

4. Hand-tighten the screw nut(s) on each cable to secure the

connection.

C. Two 800, 900, or 1100 Series™ Units

1. Insert one end of the AS EC 10E cable into the Ethernet port on

the back of the first control head. The connectors are keyed to

prevent incorrect installation, so be careful not to force the

connectors into the port.

2. Insert the other end of the AS EC 10E cable into the Ethernet

port on the second control head.

3. Hand-tighten the screw nut(s) on each cable to secure the

connection.

Hand-Tightening the Screw ut

The connector is

keyed to prevent

incorrect installation.

Screw

Nut

5Installation

Andere Handbücher für 700 series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Humminbird Schiffsausrüstung Handbücher

Humminbird

Humminbird i-PILOT LINK Bedienungsanleitung

Humminbird

Humminbird HDR 400I Bedienungsanleitung

Humminbird

Humminbird HELIX 5 G2 SERIES Bedienungsanleitung

Humminbird

Humminbird Side Imaging Transducer Bedienungsanleitung

Humminbird

Humminbird HELIX 9 Bedienungsanleitung

Humminbird

Humminbird ONIX Bedienungsanleitung

Humminbird

Humminbird HDR 650 Bedienungsanleitung

Humminbird

Humminbird Fishin' Buddy MAX Bedienungsanleitung

Humminbird

Humminbird 1158c Combo Bedienungsanleitung

Humminbird

Humminbird TS1-3 Bedienungsanleitung

Humminbird

Humminbird Trolling Motor 360 Imaging Bedienungsanleitung

Humminbird

Humminbird PiranhaMAX 155 Bedienungsanleitung

Humminbird

Humminbird LCR 2000 Bedienungsanleitung

Humminbird

Humminbird LCR 4x6 Bedienungsanleitung

Humminbird

Humminbird HELIX GPS Bedienungsanleitung

Humminbird

Humminbird Helix Series Bedienungsanleitung

Humminbird

Humminbird MEGA Live Bedienungsanleitung

Humminbird

Humminbird Helix Series Bedienungsanleitung

Humminbird

Humminbird 532769-3_A Bedienungsanleitung

Humminbird

Humminbird CoastMaster Bedienungsanleitung

Humminbird

Humminbird MEGA 360 UNIVERSAL Bedienungsanleitung

Humminbird

Humminbird 500 series Bedienungsanleitung

Humminbird

Humminbird PiranhaMAX Portable 150 PT Bedienungsanleitung

Humminbird

Humminbird SOLIX series Bedienungsanleitung

Beliebte Schiffsausrüstung Handbücher anderer Marken

Clarion

Clarion CMS2 Reparaturanleitung

EBS

EBS M7000 Bedienungsanleitung

Kongsberg

Kongsberg M3 Bathy Bedienungsanleitung

NPK

NPK SCS-1002 Bedienungsanleitung

Furuno

Furuno FE-800 Bedienungsanleitung

Harken

Harken 1561 Bedienungsanleitung

Simrad

Simrad DD15 Bedienungsanleitung

Notifier

Notifier FS-BSO Bedienungsanleitung

Raymarine

Raymarine ST40 Bedienungsanleitung

E2S

E2S E2XS112UL Bedienungsanleitung

R2Sonic

R2Sonic 2026 Bedienungsanleitung

COBHAM

COBHAM SAILOR 6000 Bedienungsanleitung

Raymarine

Raymarine Maxiview ST80 Benutzerhandbuch

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Montageanleitung

Raymarine

Raymarine ST60 Tridata Benutzerhandbuch

Sonic

Sonic 2024 Bedienungsanleitung

Quicksilver

Quicksilver 88688A25 Handbuch

Furuno

Furuno Navtex NX-700-A Bedienungsanleitung