Hunter Stoves Stromstad Bedienungsanleitung

STRÖMSTAD/ ÅTTA/ SJU MODELS

CVSVARFMBW/CVSATTAFM/CVSSJUFM

Instructions for:

Installation/Operating/Maintenance/Servicing

JINSTR/STA/STS/05 REV A 09/10/17

CONTENTS INDEX:

WARRANTY………………………………………………………………………………………………………. 2

TECHINCAL SPECIFICATION………………………………………………………………………………. 3

IMPORTANT INFORMATION…………………………………………………………………………….. 4

SAFETY…………………………………………………………………………………………………………….. 5

APPLIANCE DIMENSIONS…………………………………………………………………………………. 6

PRE INSTALLATION REQUIRMENTS………………………………………………………………….. 6/7

LEGAL REQUIREMENTS……………………………………………………………………………………. 7

CLEARANCES……………………………………………………………………………………………………. 8

REMOVE INTERNAL COMPONENTS………………………………………………………………….. 9

INSTALLATION PROCEDURE…………………………………………………………………………….. 10/11

COMMISSIONING AND HANDOVER…………………………………………………………………. 11/12

OPERATING INSTRUCTIONS…………………………………………………………………………….. 13-15

MAINTENANCE &SERVICING………………………………………………………………………….. 15/16

TROUBLESHOOTING……………………………………………………………………………………….. 17/18

OPTIONAL EXTRAS…………………………………………………………………………………………. 19

SPARES……………………………………………………………………………………………………………. 20/21

INSTALLATION &COMMISSIONING CHECK LIST………………………………………………. 22

SERVICE RECORDS…………………………………………………………………………………………… 23

FULL WARRANTY INFORMATION…………………………………………………………………….. 24-25

HUNTER STOVES GROUP,

8 Emperor Way,

Exeter Business Park,

Exeter, Email: info@hunterstoves.co.uk

Devon. EX1 3QS Website: http://www.hunterstoves.co.uk

WARRANTY

HUNTER STOVES GROUP OFFER A STANDARD 2-YEAR WARRANTY IF PURCHASED THROUGH A RECOGNISED DEALER.1-YEAR

STATUTORY APPLIES IF PURCHASED THROUGH AN INTERNET COMPANY.WE ALSO OFFER AN EXTENDED 10-YEAR WARRANTY ON

NON-CONSUMABLE PARTS.PLEASE SEE THE WARRANTY SECTION AT WWW.HUNTERSTOVES.CO.UK OR ON PAGES 24-25 OF THESE

INSTRUCTIONS FOR FURTHER INFORMATION.

THE WARRANTY WILL ONLY BE VALID IF THE APPLIANCE IS INSTALLED BY AN APPROPRIATELY QUALIFIED ENGINEER IN ACCORDANCE

WITH THE MANUFACTURER’S INSTRUCTIONS AND TO THE APPROPRIATE BUILDING REGULATIONS AND/OR LOCAL BY-LAWS AND

SERVICED WITHIN 12 MONTHS OF INSTALLATION.

THIS APPLIANCE MUST BE REGULARLY SERVICED AND MAINTAINED,USING ONLY HUNTER STOVES GROUP APPROVED COMPONENTS

FOR THE WARRANTY TO BE VALID.

Technical Specification

For further information on ventilation please refer to Building Regulations Document J or your installer.

SMOKE CONTROL AREAS

This stove has been designed and assembled so that it may be used to burn wood logs in a Smoke Control Area.

Find out if you are in a Smoke Control Area by contacting your Local Authority.

The Stromstad, Atta and Sju are fitted with a permanent stop. Without the permanent stop in place the appliance is

not an exempt appliance and so may leave the householder liable for a fine up to £1000.

GENERAL

STRÖMSTAD

ATTA

SJU

Energy Efficiency Class

Nominal Heat Output

Wood

4.7kW

Energy Efficiency

104

Efficiency

Wood

78%

Mean CO (@13% O₂)

0.23%

Appliance Mass

125kg

115kg

105kg

Recommended Fuels

Wood

Seasoned Wood (less than 20% moisture content)

Log Length

250mm

FLUES

Mean Flue Gas Temperature

288°C

288˚C

Flue Gas Mass Flow

3.9 g/s

Flue Outlet Size (Top or Rear Option)

127mm

VENTILATION

Traditionally Build Homes

-Where leakage is greater than

5m³/hour/m²

-Ventilation normally required =

550mm² per kW output over

5kw

NONE

General Guidance

It is important that your stove is correctly installed

and operated as Hunter Stoves Group cannot accept

responsibility for any fault arising through incorrect

installation, use, maintenance or servicing.

These instructions cover the basic principles to

ensure satisfactory installation of the stove, although

detail may need slight modification to suit particular

local site conditions.

The installation must comply with current Building

Regulations, National and European Standards, Local

Authority Byelaws and other specifications or

regulations as they affect the installation of the

appliance.

The Building Regulations requirements may also be

met by adopting the relevant recommendations in

the current issues of British Standards BS 8303 and

BS EN 15287-1.

Only use approved fuels on this appliance.

Information about this can be found on Page 15.

This is a Domestic Appliance and must only be used in

accordance with these instructions. Do not place

articles that are affected by high temperatures on, or

near, this appliance. Do not place furniture or other

items within 1 metre of the front of this appliance.

See the note on material clearances on pages 8.

Fitting a stove in a room which also contains an

extractor fan and/or cooker hood should be avoided

where possible. If this is unavoidable, the suitability

of the space for fitting this appliance must be decided

at the discretion of a qualified installer, and a flue

draught interference test must be performed.

Do not obstruct the ventilation required for the safe

use of this appliance.

COMPETENT PERSONS SCHEME

Hunter Stoves Group recommend that this stove is

installed by a member of an accredited competent

persons scheme e.g. HETAS.

If the installer is not a member of a competent

person’s scheme, it is a legal requirement, in the UK,

to notify your Local Building Control Officer in

advance of any installation work starting.

HEALTH AND SAFETY PRECAUTIONS

Special care must be taken when installing the stove

such that the requirements of the Health and Safety

at Work Act are met.

HANDLING

This appliance is very heavy. Adequate facilities must

be available for loading, unloading and site handling.

FIRE CEMENT

Some types of fire cement are caustic and should not

be allowed to come into contact with the skin. In case

of contact, wash immediately with plenty of water.

ASBESTOS

This stove contains no asbestos. If there is a possibility

of disturbing any asbestos in the course of installation

then please seek specialist guidance and use

appropriate protective equipment.

METAL PARTS

When installing or servicing this stove, care should be

taken to avoid the possibility of personal injury.

MODIFICATION

No unauthorised modification of this appliance should

be carried out.

PLEASE READ THESE INSTRUCTIONS PRIOR TO INSTALLATION AND OPERATION. KEEP THESE

INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERANCE AND SERVICING.

THIS APPLIANCE WILL BECOME VERY HOT WHEN USED IN ACCORDANCE WITH THESE INSTRUCTIONS,

HUNTER STOVES RECOMMEND THAT AN APPROVED GUARD IS USED TO PROTECT THE YOUNG, ELDERLY

OR INFIRM FROM HARM.

THE INSTALLER COMMISSIONING SHEET CAN BE FOUND ON THE BACK COVER. PLEASE ENSURE THAT IT IS

COMPLETED PRIOR TO USE.

SAFETY

WARNING –This appliance will be hot when in

operation and due care should be taken. The supplied

operating tool or glove may be used to open the door

and operate the air controls.

AEROSOLS

Do not use an aerosol spray on or near the stove

when it is alight.

FIREGUARDS

Always use a fireguard in the presence of children, the

elderly or the infirm. The fireguard should be

manufactured in accordance with BS8423 –Fireguards

for use with solid fuel appliances.

DO NOT OVER-FIRE

It is possible to fire the stove beyond its design

capacity. This could damage the stove so watch for

signs of over-firing. If any part of the stove starts to

glow red, the stove is in an over-fire situation and the

controls should be adjusted accordingly.

Never leave the stove unattended for long periods

without first adjusting the controls to a safe setting.

Careful air supply control should be exercised at all

times.

FUME EMISSION

Properly installed, operated, this appliance will not

emit fumes. Occasional fumes from de-ashing and

refuelling may occur. Persistent fume emission must

not be tolerated.

This appliance should not be operated with the door

open.

If fume emission persist, then the following

immediate action should be taken: -

➢Open doors and windows to ventilate the room.

➢Let the fire go out, or eject and safely dispose of

fuel from the appliance.

➢Check for flue/chimney blockage and clean if

required.

➢Do not attempt to re-light the fire until the cause

of the fume emission has been identified and

corrected.

If necessary, seek expert advice.

ADVERSE WEATHER

In a small number of installations, occasional local

weather conditions (e.g. wind from a particular

direction) may cause downdraught in the flue and

cause the stove to emit fumes. In these

circumstances, the stove should not be used. A

professional flue installer will be able to advice on

solutions to this problem (e.g. anti-downdraught

cowl).

CARBON MONOXIDE DETECTOR

Hunter Stoves recommend a Carbon Monoxide

Detector that conforms to the latest issue of BS EN

50292 is placed in the same room as the appliance.

The installation of such an alarm is not considered as

a substitute for regular maintenance or servicing or

the appliance and Flue system.

IN THE EVENT OF A CHIMNEY FIRE:

➢Raise the alarm

➢Call the Fire Brigade

➢Close appliance air controls

➢Move furniture, ornaments etc. away

➢Place a fireguard in front of stove

➢Check the chimney breast for signs of

excessive heat.

If the wall is becoming excessively hot, move furniture

away.

Ensure the Fire Brigade can gain access to your roof

space in order to check for fire spread.

APPLIANCE DIMENSIONS

PRE-INSTALLATION REQUIREMENTS

PLEASE CHECK THE FOLLOWING:

Any existing chimney/flue system must be confirmed

as suitable for this appliance as defined in Building

Regulations Document J. It must be swept and

inspected, by a competent person (see notes), to

confirm that is structurally sound and free from cracks

and obstructions.

The diameter of the flue should not be less than

150mm and not more than 200mm. Flue should not

be less than 150mm and not more than 200mm. Do

not connect to systems that have large voids or

spaces. If any of these requirements are not met, the

chimney should be lined by a suitable method.

If the chimney is suspected of previously serving an

open fire it must be swept again, within a month of

regular use, to clear any soot that may have been

dislodged due to the variation in combustion levels

and higher flue gas temperature levels. The

chimney/flue system exit must comply with Building

Regulations Document J. The minimum height and

should terminate in accordance with Table 1.

CONNECTION TO THE CHIMNEY

An existing fireplace opening can be bricked up or

sealed with a register plate. A short length of flue

pipe of minimum 150mm internal diameter may then

be used to connect the stove to the chimney. This

flue pipe should be made of 316 grade stainless steel

or vitreous enamelled steel, nominal thickness

1.2mm. Ensure that the pipe end is no closer than

76mm to the chimney walls. The length of any

horizontal run of flue pipe must not exceed 150mm.

It is essential that all connections between the stove

and chimney-flue are sealed and made airtight.

Make provision to access the chimney/flue system for

cleaning and the removal of debris. If there is no

existing chimney then either a prefabricated block

chimney in accordance with Building Regulations

Approved Document J, or a twin-walled insulated

stainless-steel flue to BS4543 can be used. These

chimneys must be fitted in accordance with the

manufacturer’s instructions and Building Regulations.

New masonry and flue block chimneys must meet the

requirements of Building Regulations Document J. Any

connecting flue pipe systems must also meet these

regulations.

Please check the suitability of the fireplace and/or

surround for use with this appliance before installing

it. If you have any doubts about the suitability of your

chimney, consult your local Dealer/Stockist or

Installation Engineer. Both the chimney and flue pipe

must be accessible for cleaning and if ANY part of the

chimney cannot be reached through the stove (with

baffle removed), a soot door must be fitted in a

suitable position.

FLUE OUTLET POSITIONS (DOCUMENT J):

Position on Roof

Clearances to flue exit

At or within

600mm of the ridge

At least 600mm

above the ridge

Elsewhere on a roof

(Pitched or Flat)

At least 2.3 M horizontally

from the nearest point on the

weather surface and:

a) At least 1.0 M above the

highest point of intersection

between the chimney and

weather surface; or

b)at least as high as the ridge

Below (on a pitched

roof) or within 2.3 M

horizontally to an

opening window or

dormer

At least 1.0 M above the top

of the opening

Within 2.3 M of an

adjoining or

adjacent building,

whether or not

beyond the

boundary

At least 600mm above any

part of the adjacent building

within 2.3 M

A full copy of Document J can be found here:

http://www.planningportal.gov.uk/uploads/br/BR_P

DF_ADJ_2010.pdf

LEGAL REQUIREMENTS

Hunter Stoves Group requests that before installation

and/or use of this appliance that you read these

instructions carefully to ensure that all the relevant

requirements are fully understood.

These instructions cover the basic principles to ensure

satisfactory installation of the stove, although detail

may need slight modification to suit particular local

site conditions. In all cases the installation must

comply with current Building Regulations, Local

Authority Byelaws, European and National Standards

and other specifications or regulations as they affect

the installation of the stove.

It should be noted that the Building Regulations

requirements may be met by adopting the relevant

recommendations given in British Standards BS 8303,

BS 6461 and BS 7566 as an alternative means to

achieve an equivalent level of performance to that

obtained following the guidance given in Approved

Document J.

Your local Building Control Officer can advise you

regarding the interpretation of the Regulations should

there be any questions.

This appliance must be installed by a Registered

Installer (see Competent Persons Scheme) or

approved by your local Building Control Officer.

All works undertaken must be carried out with due

care and attention to meet the requirements of the

Health & Safety code of practice and any other

legislation that may have been introduced since the

publication of these instructions.

Competent Persons Scheme

Members of the following schemes may self-certify

the installation of this stove. If the installer is not a

member of one of these schemes, your local Building

Control Department must approve the installation.

Scheme

Web address

Telephone

APHC (Association of

Plumbing and Heating

Contractors

(Certification) Limited

www.aphc.co.uk

02476 470 626

Building Engineering

Services Competence

Accreditation (BESCA

Limited)

www.hvca.org.uk /

www.besca.org.uk

0800 652 5533

HETAS Ltd (Heating

Equipment Testing

and Approval Scheme)

www.hetas.co.uk

01462 634721

NAPIT Registration Ltd

www.napit.org.uk

0870 444 1392

NICEIC Group Ltd

www.niceic.org.uk

0800 013 0900

Air Supply

The room or space containing this appliance does not

need a permanent, unobstructed air opening.

If a draught stabiliser is fitted, the air opening should

be at least 1410mm².

Due consideration should be given to air requirements

for any other appliance in the same room or space.

Any air opening must be kept clear from blockage or

obstruction.

Hearth/ Material Clearances

Hearth constructions must comply with the current

building regulations.

Your stove must be installed on a floor with adequate

load-bearing capacity, otherwise suitable measures

should be taken.

If the existing construction does not meet this pre-

requisite, suitable measures (e.g. load distributing

plate).

Care should be taken to level the stove using the

adjusting screws in the feet.

Material Clearances

Minimum Distances to

Combustible Material

All

Behind the stove

15mm (Behind

heat shield)

At the side of the stove

180mm (If side

wall protrudes in

front of stove

In front of the stove

900mm

Note: combustible material refers to any material that

will degrade when subjected to heat e.g. plaster.

No combustible material must be stored underneath

the stove.

FIREPLACE RECESS ALL

Plan view:

Side view:

The stove can be recessed in a suitable sized fireplace

but a permanent free air gap of at least 150mm on

top and 50mm at the sides (although we recommend

150mm for the sides and 50mm at the back of the

stove to obtain maximum heat output and for access

to the rear of the stove.)

The hearth should extend at least 300 mm from the

front of the stove. The stove should stand wholly

above a solid, non-combustible hearth, at least 125

mm thick (this may include the thickness of a solid

floor and a non-combustible decorative hearth).

FREE-STANDING BOTH

Plan view:

Side view:

If the stove is not to stand in a recess, it may stand

wholly above a hearth made of non-combustible

board / sheet material or tiles, at least 10mm thick.

The hearth should extend at least 150 mm from the

sides and rear of the stove, and at least 300 mm from

the front of the stove.

All walls shown in the above diagrams are non-

combustible unless otherwise indicated. All non-

combustible walls closer than 300mm to the stove

should be at least 75mm thick.

Note: To achieve the specified distances to

combustible materials, twin-wall insulated flue pipe

must be used, starting no higher than 105mm above

the stove.

Change in level to

mark safe perimeter

300 mm

50 mm

500 mm

from

jamb

150 mm

Combustible

material

125mm

Non

Combustible

150mm

Removing Internal Components

1. Open the door as detailed in the ‘Operating

Instructions’ section.

2. Remove the ash pan by simply pulling it out by its

handle.

3. Remove the grate by lifting it out. It may be

necessary insert your hand into the ash pan slot and

push the grate upwards beforehand.

4. Remove the side plates by lifting them up.

5. Remove the baffle brick by lifting it up, sliding it to

the right and then lowering it into the firebox.

4. Remove the two side bricks by lifting them up and

then swinging them into the centre of the stove

before removing.

5. Remove the two rear bricks, noting their positions

and orientation. The upper rear brick is completely

free will lift out, but the lower rear brick will need

tilting forwards before removal.

Installation Requirements

DIRECT AIR ADAPTOR

If fitting the direct air adaptor kit, read the

instructions supplied with the kit before proceeding.

Please note that Direct Air is not available on the

Strömstad Sju model.

FUEL STORAGE

Please note that the following DOES NOT apply to

the Atta and Sju models.

Fuel may be stored in the log recess underneath the

stove. The logs should be stacked in such a way that

they do not touch the heat shield at the top of the

recess.

Installation Procedure

INSTALLATION PROCEDURE

Note: If installing the direct air kit, follow the

instructions supplied with the kit before proceeding.

TOP FLUE INSTALLATION

1. If installing against a combustible wall, fit the

heat shield to the rear of the stove using the

supplied fixings.

2. Offer the stove into position.

3. Connect the flue, ensuring all joints are

sound.

REAR FLUE INSTALLATION

4. Remove the top plate by simply lifting it off.

5. Remove the two back panel retention screws.

6. Lift the back panel to remove it.

7. Swap the flue collar and blanking plate

around. To do this you may need to open the

stove door, as detailed in the ‘Operating

Instructions’ section.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hunter Stoves Kamin im Innenbereich Handbücher

Hunter Stoves

Hunter Stoves DI Lusso R6 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung