Hunter EC Bedienungsanleitung

AUTOMATIC

SYSTEM OFF

RUN TIMES

START TIMES

CURRENT TIME/DAY

WATER DAYS

SEASONAL ADJUSTMENT

MANUAL-ONE STATION1

MANUAL-ALL STATIONSALL

ALL

Residential Irrigation

Controller

Owner’s Manual and Programming Instructions.

Programador de Riego

Residencial

Manual de Operación e Instrucciones de Programación.

Programmateurs EC pour

Sites Résidentiels

Manuel de l’utilisateur et instructions de programmation

du programmateur.

Programmatori EC

Manuale dell’utente ed istruzioni per la programmazione.

Bewässerungssteuerung

Bedienungs- und Montageanleitung.

ENG

ESP

DEU

ENG

TABLE OF CONTENTS

INSTALLATION

EC Components ........................................................................ 1-2

Mounting the Controller to Wall .................................................... 3

Connecting Valves and Transformer ........................................... 3-4

Connecting the Battery ................................................................. 4

Connecting a Master Valve ........................................................... 4

Connecting a Pump Start Relay ................................................... 5

Connecting a Weather Sensor ...................................................... 5

Power Failures ............................................................................. 5

CONTROLLER PROGRAMMING AND OPERATION

Watering Schedule Form .............................................................. 6

Programming the Controller ......................................................... 7

Setting the Date and Time ................................................... 7

Setting Watering Start Times .............................................. 7

Eliminating a Program Start Time ............................................. 7

Programming the Controller (Continued)

Setting Station Run Times (Length of Watering for Each Area) ... 8

Setting Days To Water ........................................................ 8

Selecting Specific Days of the Week to Water ............................ 8

Selecting Interval Watering ...................................................... 8

Automatic ........................................................................... 8

System Off ........................................................................ 8

Programmable Rain Off ............................................................ 9

Bypass Weather Sensor ........................................................... 9

Seasonal Adjustment .......................................................... 9

Manually Run a Single Station ........................................... 9

ALL

Manually Run All Stations ............................................. 9-10

One Touch Manual Start and Advance ......................................10

Hidden Features ..........................................................................10

Programmable Delay Between Stations ....................................10

Clearing the Controller's Memory/Resetting the Controller .......10

TROUBLESHOOTING AND SPECIFICATIONS

Troubleshooting Guide ...........................................................11-12

Specifications .............................................................................12

CE Notice ...................................................................................13

RESIDENTIAL IRRIGATION CONTROLLER

Owner's Manual and Programming Instructions.

















 

 

















 

 





























  







   









AUTOMATIC

SYSTEM OFF

RUN TIMES

START TIMES

CURRENT TIME/DAY

WATER DAYS

SEASONAL ADJUSTMENT

MANUAL-ONE STATION 1

MANUAL-ALL STATIONS ALL

AUTOMATIC

SYSTEM OFF

RUN TIMES

START TIMES

CURRENT TIME/DAY

WATER DAYS

SEASONAL ADJUSTMENT

MANUAL-ONE STATION 1

MANUAL-ALL STATIONS ALL

54321PC

SEN

RST

1413 16

A C

Outdoor Model

(Internal Transformer Included)

Indoor Model

EC COMPONENTS

Note: Plug may

look different from

Illustration.

ENG

A – LCD Display

1. Run Times – Allows user to set each valve station run time

from 1 minute to 4 hours.

2. Start Times – Allows 1 to 4 start times to be set in each

program.

3. Station Number – Indicates currently selected station number.

4. Program Designator – Identifies program in use A, B, or C.

5. Day of the Week – Identifies day of the week (-E models will be

indicated by number 1 to 7)

6. Flashing Sprinkler – Indicates that watering is occurring.

7. System Off – Allows user to discontinue all programs and

stop all watering. Also allows the user to set the controller to a

timed off until dial is returned to the Automatic position.

Umbrella – Indicates Rain Sensor is suspending irrigation.

9. Seasonal Adjustment – Allows user to make run time changes

according to the seasons without reprogramming. Bars on the left

indicate seasonal adjustment percentage.

10.

Rain Drop – Indicates watering will occur on that selected day.

11. Crossed Rain Drop – Indicates watering will NOT occur on

selected day.

12. Calendar – Indicates interval watering schedule is being

programmed.

B – Wiring Compartment

13. 9-Volt Battery Connector – The alkaline battery can be used to

program the controller in the absence of AC power. Even without a

9-volt battery the EC will keep track of time for up to 1 month and

retain the program indefinitely in the event of a power outage.

14. Battery Compartment – Compartment for the 9-volt battery.

15. Terminal Strip Area – Use to attach transformer and valve wires

from their source to the controller.

16. Reset Button – Use to reset the controller.

17. Conduit Cover – Covers the field wires as they exit the conduit

into the bottom of the controller.

C – Control Buttons

Button – Increases the selected flashing display.

Button – Decreases the selected flashing display.

Button – Advances the selected flashing display to the next item.

Button – Selects program A, B or C for different watering zone

requirements.

Dial Settings

Automatic – Normal dial position for all controller automatic and

manual operation.

Current Time/Day – Allows current day and clock time to be set.

Start Times – Allows 1 to 4 start times to be set in each

program.

Run Times – Allows user to set each valve station run time from 1

minute to 4 hours.

Water Days – Allows user to select individual days to water or a

selected number of days between waterings (interval).

Seasonal Adjustment – Allows user to make run time changes

according to the seasons without reprogramming. Bars on the left

indicate seasonal adjustment percentage.

Manual-One Station – Allows user to activate a one time watering

of a single valve station.

ALL

Manual-All Stations – Allows user to activate a one time watering

of all valve stations or a few selected stations.

System Off – Allows user to discontinue all programs and stop all

watering. Also allows the user to set the controller to a timed off

until dial is returned to the Automatic position.

D – External Transformer (Indoor Model only)

A plug in transformer is provided to supply AC power to the controller.































































































      

MOUNTING THE CONTROLLER TO WALL

NOTE: The indoor EC is not water or weather resistant,

and must be installed indoors or in a protected area.

1. Secure one 25 mm screw (A) into the wall. Note: Install screw

anchors if attaching to drywall or masonry wall.

2. Slide the keyhole (B) on top of the controller over the screw.

3. Secure controller in place by installing screws in the holes (C)

below the terminal strip area.

Do not plug transformer into power source until the con-

troller is mounted and all valves have been connected.

Installing the Conduit Cover

(For indoor controller installations)

The conduit cover is provided to cover the field wires as they exit the

conduit into the bottom of the controller. The conduit cover can be

used with ½" or ¾" diameter conduit.

To install the Conduit Cover:

1. Remove the lower access panel

on the EC.

2. Slide the conduit cover on the

bottom edge of the controller.

3. Bring the conduit and field wires to the bottom

of the controller. Make sure that there is a

sufficient length of conduit so it enters the

conduit cover. There are two small notches on

the left side of the cover to route the 24VAC

wires from the external transformer, or wires

from the sensor and P/MV (if applicable).

4. Secure the conduit cover to the wall with the

screws and anchors provided.

5. Replace the lower access panel on the EC.

CONNECTING VALVES AND TRANSFORMER

1. Route control wires between valve location and controller. Typi-

cally it is recommended that at least 1 mm diameter conductor

cable be used.

2. At the valves, attach the common wire to either solenoid wire of

the valve. This is most commonly a white colored wire. Attach a

separate control wire to the remaining solenoid wire and make a

note of the color corresponding to each valve and the watering

station it controls.

3. Secure the wires with a waterproof wire connector to protect the

connection.

4. Secure the white valve common wire to the screw on the terminal

marked C. Connect the color-coded wires from the valves to their

appropriate station numbers and tighten the screws.

Conduit

Cover

5. Indoor model: route transformer cable through the left side of the

controller and connect the wires to the two screws marked AC.

WATER DAYS

SEASONAL ADJUSTMENT

WATER DAYS

SEASONAL ADJUSTMENT

Valve Common Wire

Connect the Two

Transformer Wires to

the Two AC Terminals Valve 1

Valve 2

Valve 3

Valve 4

Valve

Wires

54321PC

SEN

RST

9 V Battery

Wire Clip

WATER DAYS

SEASONAL ADJUSTMENT

WATER DAYS

SEASONAL ADJUSTMENT

54321PC

SEN

RST

9 V Battery

Battery Compartment

Valve Common Wire

Valve 1

Valve 2

Valve 3

Valve 4

Valve

Wires

Master Valve

Master Valve Wire

WATER DAYS

SEASONAL ADJUSTMENT

WATER DAYS

SEASONAL ADJUSTMENT

54321PC

SEN

RST

9 V Battery

ENG

CONNECTING THE BATTERY

Connect a 9-volt alkaline battery (not

included) to the battery wire clip located in

the lower left-hand side of the controller.

The battery will allow you to program the

controller without AC power. However, the

battery will not be able to activate any of

the station valves. AC power must resume

before watering will continue.

CONNECTING A MASTER VALVE

NOTE: Complete this section only if you have a master valve

installed. A master valve is a “normally closed” valve

installed at the supply point of the main line that opens only

when the controller initiates a watering program.

1. At the Master Valve, attach the common wire to either solenoid

wire of the valve. Attach a separate control wire to the remaining

solenoid wire.

2. The common wire will still go to the screw slot marked C. The ad-

ditional wire coming from the master valve will go in the screw slot

marked P.

Outdoor model: transformer wires are already connected to the

AC slots so all that is required is to connect primary power to the

junction box from a power source.

E – High Voltage Wiring Compartment (Outdoor Model only)

NOTE: Outdoor model is water and weather resistant.

Connecting the outdoor EC to the primary power should

only be done by a licensed electrician following all

local codes. Improper installation could result in shock

or fire hazard.

Route AC power cable and conduit through the ½" (13 mm) conduit

opening on the the left side of the bottom of the cabinet and connect

one wire to each of the two wires inside the junction box. Do not

connect high voltage wires to the AC terminals inside the controller.

Wire nuts are provided to make these wire connections. Note: For -E

models, connect the wires to the AC terminal strip located inside the

junction box.

Do not plug transformer into power source until the con-

troller is mounted and all valves have been connected.

WATER DAYS

SEASONAL ADJUSTMENT

WATER DAYS

SEASONAL ADJUSTMENT

54321PC

SEN

RST

9 V Battery

Weather Sensor

AUTOMATIC

SYSTEM OFF

RUN TIMES

START TIMES

CURRENT TIME/DAY

WATER DAYS

SEASONAL ADJUSTMENT

MANUAL-ONE STATION1

MANUAL-ALL STATIONS

ALL

PSR Series

Pump Start Relay

4.5 Meters Minimum (15')

To Pump

CONNECTING A PUMP START RELAY

NOTE: Complete this section only if you have a pump

start relay installed. A pump start relay is a device that

uses a signal from the controller to actuate a separate

electrical circuit to energize a pump to provide water to

your system.

The controller should be mounted at least 4.5 m away from both the

pump start relay and the pump.

1. Route a wire pair from the pump relay into the controller housing.

2. Connect common wire to the screw slot C (Common) and the

remaining wire from the pump relay to the P screw slot.

Relay holding current draw must not exceed .28 amps. Do not connect

controller directly to pump—damage to controller can result.

CONNECTING A WEATHER SENSOR

A Hunter weather sensor or other type of micro-switch weather sensor

can be connected to the EC. The purpose of this sensor is to stop

watering when weather conditions dictate.

1. Remove the jumper that is attached across the SEN terminals of

the controller.

2. Connect one wire to the SEN terminal and one to the other

SEN terminal.

NOTE: If the rain sensor is interrupting irrigation you can

bypass it by using any of the following: MANUAL-ONE

STATION, MANUAL-ALL STATIONS, or ONE TOUCH START

AND ADVANCE. See section “Rain Sensor Bypass” for

more information.

POWER FAILURES

Due to the possibility of power failures, the controller has non-volatile

memory. Programmed information will never be lost. The controller

will keep the correct time for up to 1 month without power. Normal

watering will resume when AC power is restored.

ENG

PROGRAM A PROGRAM B PROGRAM C

LOCATION

STATION

STATION RUN TIME STATION RUN TIME STATION RUN TIME

PROGRAM

START TIMES

HUNTER EC

NOTES:

DAY OF THE WEEK

INTERVAL (Choose 1 to 31 days)

WATERING SCHEDULE FORM

CURRENT TIME/DAY

7711 22 33 44 55 66

START TIMES

PROGRAMMING THE CONTROLLER

The EC display shows time and day when the controller is idle. The

display changes when the dial is rotated to indicate the specific

programming information to enter. When programming, the flashing

portion of the display can be changed by pressing the or

buttons. To change something that is not flashing, press the button

until the desired field is flashing.

Three programs A, B and C each with the ability to have four daily

start times, permit plants with different watering requirements to be

separated on different day schedules.

NOTE: A basic programming rule is that whatever symbol

or character is flashing will be the item programmed.

For instance, if the hour is flashing when setting the

time, the hour can be changed or programmed. For illus-

tration purposes, flashing characters are in GRAY type.

Setting the Date and Time

1. Turn the dial to the CURRENT TIME/DAY

position.

2. Hours will be flashing. Press the or

button to change the hour shown on the

display. Press the to proceed to setting

the minutes.

3. Minutes will be flashing. Use the or

button to change the minutes shown on the

display. Press the to proceed to select

AM, PM, or 24 hour time.

4. The time will be displayed, and an arrow will

be flashing on AM. Press the and but-

tons to select AM, PM, or 24 hour. Press the

to proceed to setting the day of the week.

5. The number for day 1 will be flashing. Press

the and to select the day of the week

corresponding to the day.

The time and day have now been set. You can turn the dial to

AUTOMATIC to display the current time.

Setting Watering Start Times

1. Turn the dial to the START TIMES position.

2. The factory preset is set on program A. If

necessary, you can select program B or C

by pressing the button.

3. Use the or button to change the start

time. (The start times advance in

15 minute increments).

4. Press the button to select the next start time, or press for

the next program.

NOTE: One start time will activate all stations sequen-

tially in that program. This eliminates the need to

enter each station’s start time. Multiple start times in a

program can be used for separate morning, afternoon, or

evening watering cycles.

Eliminating a Program Start Time

With the dial set to the SET WATERING START

TIMES position, push the or button until

you reach 12:00 am (Midnight). From here push

the button once to reach the OFF position.

Inhaltsverzeichnis

Andere Hunter Controller Handbücher

Hunter

Hunter X-CORE Betriebsanleitung

Hunter

Hunter PRO-C Hydrawise Stücklistenhandbuch

Hunter

Hunter SRC Plus Bedienungsanleitung

Hunter

Hunter Pro-C Bedienungsanleitung

Hunter

Hunter ICC2 Bedienungsanleitung

Hunter

Hunter Pro-C Bedienungsanleitung

Hunter

Hunter Genesis Bedienungsanleitung

Hunter

Hunter HCC Installationshandbuch

Hunter

Hunter NODE-BT Bedienungsanleitung

Hunter

Hunter Eco-Logic 6 Betriebsanleitung

Hunter

Hunter X2-400 Betriebsanleitung

Hunter

Hunter X-CORE XC-800I Betriebsanleitung

Hunter

Hunter XC hybrid Betriebsanleitung

Hunter

Hunter ICC-800PL Betriebsanleitung

Hunter

Hunter Pro-C PCM-1600 Bedienungsanleitung

Hunter

Hunter VSX Bedienungsanleitung

Hunter

Hunter X-CORE Bedienungsanleitung

Hunter

Hunter 600-Z Bedienungsanleitung

Hunter

Hunter SVC Bedienungsanleitung

Hunter

Hunter 27178 Bedienungsanleitung

Hunter

Hunter X-Core XC-801i-E Betriebsanleitung

Hunter

Hunter Hydrawise Ready Bedienungsanleitung

Hunter

Hunter PRO-C PC Series Betriebsanleitung

Hunter

Hunter PSC-Z Series Betriebsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch