Hunter Hydrawise HC-1200M Bedienungsanleitung

hunterindustries.com

HC IRRIGATION CONTROLLER

Quick Start Guide

Hydrawise™Ready

TABLE OF CONTENTS

HC SUPPORT

Thank you for purchasing the Hunter HC Controller. In this Quick Start Guide you will

learn how to install and congure the HC Controller and connect to Wi-Fi.

For support for Hydrawise™ cloud soware or help with your Hydrawise account,

please visit hunter.direct/hchelp.

Your controller is shipped with:

• A Hunter Wi-Fi controller

• 24V AC transformer

• 2x screws and wall anchors for wall mounting

Installation 1

Connecting to a Wi-Fi Network 3

Connecting Solenoid Valves and Plug Packs 4

App Conguration 6

INSTALLATION

Installing the HC Controller

The HC is designed for indoor installations only. The chosen location must have Wi-Fi

coverage. Wi-Fi coverage can be easily tested using a smart phone. A signal strength of

2 or 3 bars is recommended. Wi-Fi connectivity can also be tested on the HC itself (signal

strength is shown when you select a wireless network).

Cable Entry

The controller has two cable entry

options – from the rear of the case

or via a conduit from the bottom of

the controller.

Entry from the rear of the controller

Using a sharp knife, remove the two

cutouts on the rear of the controller

as indicated on the diagram as .

Entry via ⁄ inch conduit

Using a sharp knife, cut around the

semi-circular line on the controller as

indicated on the diagrams as . Cut

around the matching line on the blue

controller wiring cover.

Note: The HC Controller is an

indoor model and is not water-

proof or weather resistant, and

must be installed indoors or in a

protected area.

Note: Do not plug the

transformer into power source

until controller is mounted and

all wiring has been connected.

Mounting the controller

1. Using a drill bit of ⁄ inch diameter,

drill a hole to a depth of 1 inch

(25 mm).

2. Insert plastic anchor so it is ush

with the surface of the wall.

3. Screw 1 inch screw into anchor

leaving the head protruding about

⁄ inch (4 mm).

4. Slide the controller case over the

screw head.

5. Mark second mounting point (see 

in diagram), remove controller, drill

hole, insert plastic anchor, slide

controller case over rst screw head

and screw into place.











 

 Rear cable entry point

(remove with knife)

Conduit cable entry point

(remove with knife)

Wall mounting screw

Power indicator

Expansion module

cable entry

Go to previous screen

Go to home screen

CONNECTING TO A WI-FI NETWORK

When your controller is rst powered on it will run a short wizard to connect your

controller to your wireless router.

If you’re not using the initial startup wizard then go to the Viewing Wireless Settings

section to change your wireless settings at hunter.direct/hchelp.

Using the Wizard

1. Select your wireless network from the list shown on the controller display

and press the Conrm button on screen.

2. Enter your wireless password and press the OK button on keyboard.

When connecting to your wireless network, the Wi-Fi Icon at the bottom right of the

controller screen will ash. Connecting takes about 30 seconds and when successfully

connected the Wi-Fi Icon will stop ashing and stay on.

Note: If your network is not listed then check that the

unit is within wireless range.

Note: Make sure you press the OK button aer you’ve

entered your password. Pressing the Home or Back

buttons will not save your changes.

CONNECTING TRANSFORMER & SOLENOID VALVES

Your controller has either 6 or 12 zones depending on the model you have purchased.

There are three COMMON wiring points for convenience – any or all of them can be used.

Refer to the diagram below when connecting your solenoid valves to the controller.

 Water main

Master valve (optional)

Solenoid valves

Water to zones

 Common wires

 24V AC plug pack



 







Connecting the Transformer

Step 1 Step 2

Use the transformer supplied and connect

the wires to the red AC terminal blocks

on the unit marked as 24V. Polarity of the

wiring is not important.

Turn the power on. The power indicator

will light up (see  previous page).

Step 4 Step 5 Step 6

Connect each of the

other solenoid wires to

one of the ZONE inputs.

If a master valve (sometimes

labeled as MV on other

controllers) is installed, it can

be connected to any spare

zone as any of the zones can

be assigned as a master valve

output. Conguration of the

master valve in the Hydrawise

app is required.

Click the blue wiring

cover into place to

seal the controller and

protect the wiring.

Solenoid Valve Wiring

Step 1 Step 2 Step 3

Take one wire from each

solenoid, twist together

and connect to the common

(usually white) wire of your

multicore irrigation cable.

Note: All wire connections

should be done using

waterproof connectors.

Connect each of the

other individual wires to

a dierent colored wire.

Record zones against wire

color for later reference.

Connect the common

wire from the multicore

cable (usually white) to

any of the three terminals

on the controller marked

COMMON.

HYDRAWISE APP CONFIGURATION

To connect the HC Controller to the Hydrawise app, follow these steps and then follow

the on-screen instructions.

1. If you have not already done so, create an account at the Hydrawise website.

Go to Hydrawise.com and register for an account.

2. Log into your account. If this is the rst time that you have logged in, you will be

guided through a setup wizard to help you with initial conguration of your controller.

Canadian FCC Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de

brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

US FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy, and if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation

distance of 20 cm or more should be maintained between the antenna of this device and persons during

operation. To ensure compliance, operation at closer than this distance is not recommended. The antenna(s)

used for this transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

Andere Handbücher für Hydrawise HC-1200M

Inhaltsverzeichnis

Andere Hunter Controller Handbücher

Hunter

Hunter SRC Plus Bedienungsanleitung

Hunter

Hunter Pro-C Betriebsanleitung

Hunter

Hunter X2-400 Betriebsanleitung

Hunter

Hunter SpectraProbe XE Gebrauchsanweisung

Hunter

Hunter NODE-BT Bedienungsanleitung

Hunter

Hunter 27206 Bedienungsanleitung

Hunter

Hunter Pro-HC601-A Bedienungsanleitung

Hunter

Hunter Genesis Bedienungsanleitung

Hunter

Hunter Hydrawise HCC-800-PL Bedienungsanleitung

Hunter

Hunter ACC-1200 Bedienungsanleitung

Hunter

Hunter Hydrawise HC-1200M Bedienungsanleitung

Hunter

Hunter ICC2 Bedienungsanleitung

Hunter

Hunter ACC2 Installationshandbuch

Hunter

Hunter XC HYBRID Series Leitfaden

Hunter

Hunter NODE-BT Bedienungsanleitung

Hunter

Hunter SRC Plus Bedienungsanleitung

Hunter

Hunter ICC Series Bedienungsanleitung

Hunter

Hunter ICC2 Bedienungsanleitung

Hunter

Hunter ICC2 Bedienungsanleitung

Hunter

Hunter Pro-C Betriebsanleitung

Hunter

Hunter Node Bedienungsanleitung

Hunter

Hunter XC Hybrid Betriebsanleitung

Hunter

Hunter X-CORE Betriebsanleitung

Hunter

Hunter PRO-C Hydrawise Stücklistenhandbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch