Hunter Field Server 3000 Bedienungsanleitung

Field Server

Automation Gateway

OWNER’S MANUAL

FS3000 and FS1000

hunterindustries.com |Built on Innovation®

eldserver operating manual

CONTENTS

About the Field Servers............................... 3

Certication ................................................... 3

Supplied Equipment ...................................... 3

Equipment Setup ......................................... 3

Mounting....................................................... 3

Physical Dimensions ...................................... 4

Installation ................................................... 5

DIP Switch Settings ....................................... 5

Bias Resistors ................................................ 5

Termination Resistor...................................... 6

Connecting the R1 and R2 Ports..................... 6

Wiring ............................................................ 6

Supported RS-485 Baud Rates

by Protocol..................................................... 7

10/100 Ethernet Connection Port .................. 7

Powering up the Gateway ........................... 7

Connecting the PC to the Gateway ............. 8

Connecting to the Gateway via Ethernet ....... 8

Changing the Subnet of the Connected PC.... 8

Setting Up Web Server Security ................. 9

Logging In to the Field Server........................ 9

Selecting the Security Mode.........................10

HTTPS with Own Trusted TLS Certicate ......10

HTTPS with Default Untrusted

Self-Signed TLS Certicate or HTTP

with Built-in Payload Encryption...................10

Setting Up the Network...............................11

Using FS-GUI to Input Network Settings .......11

Routing Settings............................................11

Eth1 and Eth2

Network Settings – LAN Mode...................... 12

Ethernet 2 Network Settings – WAN Mode.....12

Conguring the Field Server ...................... 13

Retrieving the Sample Conguration File ..... 13

Changing the Conguration File to Meet

the Application ............................................. 13

Loading the Updated Conguration File ....... 13

Using FS-GUI to Input Load a

Conguration File ......................................... 13

Retrieving the Conguration File for

Modication or Backup.................................14

Testing and Commissioning the Field Server..14

Accessing the Field Server Manager............. 14

Troubleshooting.......................................... 15

Lost or Incorrect IP Address.......................... 15

Viewing Diagnostic Information.................... 15

Checking Wiring and Settings....................... 15

Taking a Field Server Diagnostic Capture......16

LED Functions............................................... 17

Factory Reset Instructions............................ 17

Internet Browser Soware Support.............. 17

Additional Information............................... 17

Changing the Web Server Security

Settings Aer Initial Setup............................ 17

Changing the Security Mode ........................18

Editing the Certicate Loaded onto

the Field Server.............................................18

Changing the User Management Settings ..... 18

Creating Users .............................................. 19

Editing Users .............................................19

Deleting Users ...........................................19

Changing the Field Server Password.........20

Specications............................................20

Warnings ..................................................20

Complying with EN IEC 62368-1................20

Limited 2-Year Warranty...........................21

eldserver operating manual

ABOUT THE FIELD SERVERS

The Field Server is a high performance,

cost eective building and industrial

automation multi-protocol gateway

providing protocol translation between

serial/Ethernet devices and networks.

NOTE: For troubleshooting assistance,

refer to the Troubleshooting section or

any of the troubleshooting appendices

in the related driver supplements. Check

the Hunter Industries website for tech-

nical

support resources and documentation

that may be of assistance.

The Field Server is cloud-ready and

connects with Hunter Industries’s Grid.

See the section on Accessing the Field

Server Manager for more information.

Certication

BTL Mark – BACnet™

Testing Laboratory

The BTL Mark on the Field Server is a

symbol indicating that a product has

passed a series of rigorous tests

conducted by an independent

laboratory. This veries that the

product correctly implements the

BACnet features claimed in the listing.

The mark is a symbol of a high-quality

BACnet product.

Go to www.BACnetInternational.net

for more information about the BACnet

Testing Laboratory. You can view the

BACnet Protocol Implementation

Conformance Statement (PICS) at

bacnet.org/conformance-pics/. BACnet

is a registered trademark of ASHRAE.

Supplied Equipment

Field Server Gateway

• Preloaded with two selected drivers

and a sample conguration le.

EQUIPMENT SETUP

Mounting

The gateway can be mounted using the

DIN rail mounting bracket on the back of

the unit.

DIN Rail

Bracket

eldserver operating manual

Physical Dimensions

3.94"

(100 cm)

1.10"

(28 cm)

2.76"

(70 cm)

3.07"

(78 cm)

eldserver3000

Input: 24VAC, 50/60Hz or 8-30VDC 0.3A

Default Password: Password

Shipped IP 1: xxx xxx xxx xxx

ETH 1 MAC: xx xx xx xx xx xx

Shipped IP 2: xxx xxx xxx xxx

ETH 2MAC: xx xx xx xx xx xx

SO#: Sale Order

Product of China

FS-N64-XXXX

eldserver

Power Port

R2 Serial Port R1 Serial Port

TX+

RX-

GND

RX2TX2

OFF ON

TERM

BIAS-

BIAS+

TERM

BIAS-

BIAS+

485/232

OFF ON

Micro SD

9-30 VDC

24 VAC

FG N L

NEC Class 2 Wiring

RX2

ETH 2 ETH 1

WAN LAN

TX2

BTN

$$ ERR PWR

E467736

REF

eldserver operating manual

INSTALLATION

DIP Switch Settings

Bias Resistors

To enable Bias Resistors, move both the

BIAS- and BIAS+ dip switches to the

right in the orientation shown above.

The bias resistors are used to keep the

RS-485 bus to a known state, when

there is no transmission on the line (bus

is idling), to help prevent false bits of

data from being detected. The bias

resistors typically pull one line high and

the other low  far away from the

decision point of the logic.

The bias resistor is 510 ohms, which is in

line with the BACnet spec. It should only

be enabled at one point on the bus (for

example, on the eld port were there

are very weak bias resistors of 100k).

Since there are no jumpers, many

Field Servers can be put on the network

without running into the bias resistor

limit, which is < 500 ohms.

NOTE: See ni.com/support/serial/

resinfo.htm for additional information.

NOTE: The R1 and R2 DIP switches apply

settings to the respective serial port.

NOTE: If the gateway is already powered

on, DIP switch settings will not take

eect unless the unit is power cycled.

R1 Bias Resistor DIP

switches (2 and 3)

R2 Bias Resistor DIP

switches (2 and 3)

eldserver operating manual

Connect to the 3-pin connector(s) as

shown below.

Wiring

NOTE: The RS-485/RS-232 is part of the

RS-485/RS-232 interface and must be

connected to the corresponding terminal

on the BMS. If the cable is shielded, the

shield must be connected only at one

end and to earth ground. This will help

suppress the electromagnetic eld

interference. (Connecting the shield at

both ends will likely produce current

loops, which could produce noise or

interference that the shield was

intended to block).

Termination Resistor

If the gateway is the last device on the

serial trunk, then the End-Of-Line

Termination Switch needs to be enabled.

To enable the Termination Resistor,

move the TERM dip switch to the right in

the orientation shown above.

Termination resistor is also used to

reduce noise. It pulls the two lines of an

idle bus together. However, the resistor

would override the eect of any bias

resistors if connected.

NOTE: The R1 and R2 DIP switches apply

settings to the respective serial port.

NOTE: If the gateway is already

powered on, DIP switch settings will

not take eect unless the unit is

power cycled.

Connecting the R1 & R2 Ports

For the R1 port only: Switch between

RS-485 and RS-232 by moving the

number 4 DIP switch le for RS-485

and right for RS-232 (see images in

DIP Switch Setting section).

The R2 port is RS-485.

R1 Bias Resistor DIP

switches (2 and 3)

R2 Bias Resistor DIP

switches (2 and 3)

+  GND

TX+ RX GND

RS-485 RS-232

BMS RS-485

Wiring

Gateway Pin

Assignment

BMS RS-232

Wiring

Gateway Pin

Assignment

RS-485+ TX+ RS-232- TX+

RS-485- RX- RS-232+ RX-

GND GND GND GND

eldserver operating manual

NOTE: The Default IP Address of the

gateway is 192.168.2.101, and the Subnet

Mask is 255.255.255.0.

NOTE: The ETH2 port can be set to WAN

mode to limit Ethernet trac. See the

WAN Mode Settings for ETH2 section

for details.

NOTE: ETH1 and ETH2 must be

congured with IP Addresses on

dierent IP subnets.

POWERING UP THE GATEWAY

Check power requirements in the

table below:

NOTE: These values are “nominal” and

a safety margin should be added to the

power supply of the host system. A

safety margin of 25% is recommended.

Apply power to the Field Server as

shown on next page. Ensure that the

power supply used complies with the

specications provided in the

Specications section.

• The gateway accepts 9 to 30 VDC or

24 VAC on pins L+ and N-.

- Supports both Full-Wave and

Half-Wave AC

• Frame GND should be connected to

ensure personnel safety and to limit

material damages due to electrical

faults. Ground planes are susceptible

to transient events that cause sudden

surges in current. The frame ground

connection provides a safe and

eective path to divert the excess

current from the equipment to

earth ground.

Supported RS-485 Baud Rates

by Protocol

The supported baud rates for either port

is based on the protocol of the connected

devices. The following baud rates are

supported for Modbus RTU:

2400, 4800, 9600, 19200, 38400,

57600, 76800, 115200

The following baud rates are supported

for BACnet MS/TP: 9600, 19200,

38400, 76800, 115200

10/100 Ethernet Connection Port

NOTE: Do not use shielded Ethernet

cables.

The Ethernet port is used both for

BACnet/IP communications and for

conguring the gateway via the Web

App. To connect the gateway, either

connect the PC to the router’s Ethernet

port or connect the router and PC to an

Ethernet switch. Use Cat-5 cables for

the connection.

Ethernet Port 1 ETH1

Ethernet Port 2 ETH2

Power Requirement for Field Server External Gateway

Current Draw Type

Field Server Family 12VDC 24vdc/ac

FS-QS-3X109-XXXX (typical) 250mA 125mA

eldserver operating manual

Changing the Subnet of the

Connected PC

The default IP address for the

Field Server is 192.168.2.101, and the

Subnet Mask is 255.255.255.0. If the

PC and Field Server are on dierent IP

networks, assign a static IP address to

the PC on the 192.168.2.xxx network.

For Windows 10:

• Find the search eld in the local

computer’s taskbar (usually to the

right of the Windows icon) and type

in Control Panel.

• Click Control Panel, Network and

Internet, then Network and Sharing

Center in that order.

• Click Change Adapter Settings on the

le side of the window.

• Right-click on Local Area Connection,

and select Properties from the

dropdown menu.

• Highlight and then click the

Properties button.

• Select and enter a static IP address on

the same subnet. For example:

swx

• Click the Okay button to close the

Internet Protocol window. Next, select

the Close button to close the Ethernet

Properties window.

NOTE: Floating AC power supplies

are supported.

CONNECTING THE PC TO

THE GATEWAY

Connecting to the Gateway via Ethernet

Connect a Cat-5 Ethernet cable (straight

through or cross-over) between the local

PC and Field Server ETH1 (LAN port).

Power to

Gateway

Pin Label

Assignment

Power in (+) L + V +

Power In (-) N- V -

Frame GND FG Frame GND

Ethernet Port

eldserver operating manual

• Additional text will expand below the

warning. Click the underlined text

to go to the IP address. In the

example below, this text is “Proceed

to 10.40.50.94 (unsafe).”

• When the login screen appears, put in

the Username (default is “admin”) and

the Password (found on the label of

the Field Server).

NOTE: There is also a QR code in the

top right corner of the Field Server label

that shows the default unique password

when scanned.

NOTE: A user has ve attempts to log

in. Aerward, there will be a 10-minute

lockout. There is no timeout on the Field

Server to enter a password.

NOTE: To create individual user logins,

go to the Change User Management

Settings section.

SETTING UP WEB SERVER

SECURITY

Logging In to the Field Server

The rst time the Field Server GUI is

opened in a browser, the IP address for

the gateway will appear as “untrusted.”

This will cause the following pop-up

windows to appear.

• When the Web Server Security

Uncongured window appears, read

the text and choose whether to move

forward with HTTPS or HTTP.

• When the warning that “Your

connection is not private” appears,

click the advanced button on the

bottom le corner of the screen.

eldserver operating manual

• Copy and paste the Certicate and

Private Key text into their respective

elds. If the Private Key is encrypted,

type in the associated Passphrase.

• Click Save.

• A “Redirecting” message will appear.

Aer a short time, the Field Server

GUI will open.

HTTPS with Default Untrusted Self-

Signed TLS Certicate or HTTP with

Built-in Payload Encryption

• Select one of these options and click

the Save button.

• A “Redirecting” message will appear.

Aer a short time, the Field Server

GUI will open.

Selecting the Security Mode

On the rst login attempt to the Field

Server, the following screen will appear.

It allows the user to select the mode that

the Field Server should use.

NOTE: Cookies are used for

authentication.

NOTE: To change the web server

security mode aer initial setup, go to

the Change Web Server Security

Settings Aer Initial Setup section.

The sections that follow include

instructions for assigning the dierent

security modes.

HTTPS with Own Trusted

TLS Certicate

This is the recommended selection and

the most secure. Please contact your IT

Department to nd out if you can obtain

a TLS certicate from your company

before proceeding with the Own Trusted

TLS Certicate option.

• Once this option is selected, the

Certicate, Private Key and Private

Key Passphrase elds will appear

under the mode selection.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hunter Tor Handbücher

Hunter

Hunter ADASLink Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung