Hunter Hydrawise HC-1200M Bedienungsanleitung

Table of Contents

Wire Distance (Controller to Valve)

Pump Start Relay Wiring and Software Setup

One Master Valve - Two Controllers

Master Valve Wiring and Software Setup

Sprinklers Running with the Controller Off or Unplugged

Wire Distance (Controller to Valve)

Below is a chart indicating the maximum wire runs that can be used when installing

Hunter AC solenoids and valves.

Valve Wire Sizing (Maximum One-Way Distance in Feet Between Controller and Valve)

Ground

Wire Size Control Wire (ft)

18 AWG /

1.0 mm

16 AWG /

1.2 mm

14 AWG /

1.6 mm

12 AWG /

2.0 mm

10 AWG /

2.5 mm

8 AWG / 3

6 AWG / 4

18 AWG / 1.0

mm 850 1040 1210 1350 1460 1540 1590

16 AWG / 1.2

mm 1040 1340 1650 1920 2150 2330 2440

14 AWG / 1.6

mm 1210 1650 2150 2630 3080 3450 3700

12 AWG / 2.0

mm 1350 1920 2630 3390 4170 4880 5400

10 AWG / 2.5

mm 1460 2150 3080 4170 5400 6670 7690

8 AWG / 3

mm 1540 2330 3450 4880 6670 8700 10530

6 AWG / 4

mm 1590 2440 3700 5400 7690 10530 13330

Pump Start Relay Wiring and

Software Setup

In this article, we will discuss the following topics:

Summary

Operation Chart

Wiring (24 VAC)

Wiring to Power Source

Software Setup

Pump Start Relay Operation per Zone

Summary

When a system requires the use of a booster pump or pulls water directly from a creek or

pond, it’s imperative to include a relay to activate the pump each and every time. A pump

start relay is a relay box that activates a pump every time a zone is activated from the

controller. Zone valves are the individual valves that operate a group of sprinklers or drip

emitters. Hydrawise controllers support 6- to 54-zone valves, depending on the model.

Typically, one zone valve is turned on at a time and controls the irrigation in a specific area

of your landscape. Whenever one of the irrigation zone valves is told to open by the

controller, the controller also signals the pump start relay to turn the pump on.

Operation Chart

Controller Model Set Master Valve Operation

HC ON or OFF by All Zones

PRO-HC ON or OFF by All Zones

X2 w/WAND WiFi Module ON or OFF by Zone or All Zones

HPC ON or OFF by Zone or All Zones

HCC ON or OFF by Zone or All Zones

Wiring (24 VAC)

Use a minimum distance of 15' (4.5 m) between the controller and the relay to dampen

electromagnetic noise. In addition to this recommendation, Hunter also recommends all

controllers be mounted 15' (4.5 m) away from pumps and high-voltage devices.

1. Detach the pump start relay cover plate by removing the four screws with a

Phillips screwdriver.

2. Run a single wire from the "common" terminal on the controller to one of the yellow

wires on the pump start relay.

3. Run a single wire from the "P/MV" terminal on the controller to the other yellow wire on

the pump start relay.

4. Use wire nuts to make the connections and verify they are secure.

5. Install pump start relay cover plate and four screws. Close and lock the cabinet door.

6. Route wire through the conduit or one of the openings on the bottom of the cabinet.

7. Strip ½" (13 mm) of insulation from the ends of all wires. Secure the valve common

wire to the “COM” (Common) terminal. Attach the opposite control wire to the M/V

terminal.

Pump Start Relay Maximum Wire Lengths

MAXIMUM one-way wire length (do not go this far!)

Model 18 AWG 16 AWG 14 AWG 12 AWG 10 AWG 8 AWG

PSR-22 243 ft 386 ft 616 ft 976 ft 1,551 ft 2,463 ft

PSR-52 134 ft 214 ft 341 ft 540 ft 859 ft 1,365 ft

PSR-53 134 ft 214 ft 341 ft 540 ft 859 ft 1,365 ft

Wiring Illustrations

HC PRO-HC

HPC HCC

X2 w/WAND WiFi Module

NOTE: With an HC Hydrawise controller, any one of your 6 or 12 zones can be configured

to act as the pump start relay. We usually recommend wiring to the last zone that is not

being used in the controller.

Wiring to Power Source

Connecting the pump start relay should only be done by a licensed electrician following

local codes. Improper installation could result in shock or fire hazard.

1. To prevent electric shock, turn the main circuit-breaker switch to “off” prior to making

electrical connections.

2. Assemble conduit piping and connect AC power from the power source to one side

(LINE IN) of the relay.

3. Assemble conduit piping and connect wiring from the pump motor to the other side of

the relay (LOAD OUT).

4. Check to make sure there are no exposed or loose connections.

Software Setup

This setup option is prompted when you first go through the initial setup wizard in the

software.

The online instructions will refer to a MASTER VALVE but this same setting applies when

using a PUMP START RELAY (PSR).

NOTE: With an HC Hydrawise controller, any one of your 6 or 12 zones can be configured

to act as the pump start relay. We usually recommend wiring to the last zone that is not

being used in the controller.

If you need to change this in the software after the setup wizard, refer to the instructions

below.

1. Log in to your Hydrawise account

2. Click on ZONES AND SCHEDULES for the PC or ZONES if using the mobile app.

3. Choose YES from the drop-down menu above the zones. If you have an HC controller,

choose the zone number to which you have the master valve wired.

HC Controller X2 w/WAND, PRO-HC, HPC, and HCC Controllers

Pump Start Relay Operation per Station

When selecting a PUMP START RELAY to be on/off for an individual zone, you can edit

the zone in ZONES AND SCHEDULES under ADVANCED SETTINGS. This option is

useful when one zone is using city water and another is using water from a different

source. This option is for X2 w/WAND, HPC, and HCC controllers only.

Follow the steps below to change this setting:

1. From the ZONES AND SCHEDULES page, click on the ( ) icon on the zone you

would like to edit.

2. Click on ADVANCED, which is located on the top blue search section.

3. Select USE GLOBAL MASTER VALVE SETTING to keep this circuit on or select

DISABLE MASTER VALVE to turn it off.

One Master Valve - Two

Controllers

There are many times when two controllers are being supplied from a single POC (point of

connection) or source of water. Hydrawise-ready controllers can be connected to a single

master valve using a isolation relay (part number REL2). This device will allow for two

controllers to share the same master valve with out any issues.

The few limitations include:

Only one controller can operate at a time.

A delay of at least five minutes between the operation of controller #1 and controller #2

is desirable.

Electrical alerts will apply for each controller.

Steps for set up.

1. Wire the relay according to the drawing below.

2. Set up the master valve in the the app for both controllers using the normal instructions

in the article here [1].

3. Set up a new master valve using the app for controller #2 as per normal instructions.

REL 2 is NEVER connected to high voltage. It is for 24 VAC devices only.

Master Valve Wiring and Software

Setup

In this article, we will discuss the following topics:

Brief Summary

Operation Chart

Wiring

Software Setup

Master Valve (P/MV) Operation per zone

Brief Summary

A master valve is a normally closed valve installed at the supply point of the mainline that

opens only when the automatic system is activated. Zone valves are the individual valves

that operate a group of sprinklers or drip emitters. Hydrawise controllers support 6 - 54

zone valves, depending on the model. Typically one zone valve is turned on at a time and

controls the irrigation in a specific area of your garden. Whenever one of the irrigation zone

Andere Handbücher für Hydrawise HC-1200M

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hunter Bewässerungssystem Handbücher

Hunter

Hunter I-25 Bedienungsanleitung

Hunter

Hunter INSTITUTIONAL SERIES I-90 Bedienungsanleitung

Hunter

Hunter I-20 ULTRA Bedienungsanleitung

Hunter

Hunter Institutional I-40 Bedienungsanleitung

Hunter

Hunter Professional Series Bedienungsanleitung

Hunter

Hunter Institutional Series Bedienungsanleitung

Hunter

Hunter PGP Series Bedienungsanleitung

Hunter

Hunter TTS-800 Series Bedienungsanleitung

Hunter

Hunter XC Hybrid Bedienungsanleitung

Hunter

Hunter Institutional I-40 Series Bedienungsanleitung

Hunter

Hunter Professional Series PGP Bedienungsanleitung

Hunter

Hunter Institutional Series Bedienungsanleitung

Hunter

Hunter Institutional Series Bedienungsanleitung

Hunter

Hunter Professional PGP Ultra Series Bedienungsanleitung

Hunter

Hunter Institutional Series Bedienungsanleitung

Hunter

Hunter Institutional Series Bedienungsanleitung

Hunter

Hunter Institutional I-20 Bedienungsanleitung

Hunter

Hunter PRO-C Hydrawise Bedienungsanleitung

Hunter

Hunter I-80 Bedienungsanleitung

Hunter

Hunter Institutional Series I-90 Bedienungsanleitung

Hunter

Hunter Institutional Series I-25 Plus Bedienungsanleitung

Hunter

Hunter i-core IC-600PL Bedienungsanleitung

Hunter

Hunter Professional Series Bedienungsanleitung

Hunter

Hunter Institutional Series I-35 Bedienungsanleitung

Beliebte Bewässerungssystem Handbücher anderer Marken

Cellfast

Cellfast 52-305 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL A Bedienungsanleitung

Oral Care Technologies

Oral Care Technologies Hydro Floss Bedienungsanleitung

Reliable

Reliable F1-300 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Gem F892 Bedienungsanleitung

Netafim

Netafim NETBEAT Bedienungsanleitung

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Bedienungsanleitung

Tyco

Tyco CC3 Bedienungsanleitung

Reliable

Reliable F4FR Bedienungsanleitung

OpenSprinkler

OpenSprinkler OSPi Bedienungsanleitung

EINHELL

EINHELL GE-WW 5537 E Bedienungsanleitung

Valley

Valley Bender160 Bedienungsanleitung

Reliable

Reliable F1FR42 Series Bedienungsanleitung

Reliable

Reliable F1FR-300 Bedienungsanleitung

Toro

Toro 730 Series Kurzanleitung

Eden

Eden 97063-EDAMZ Bedienungsanleitung

Tyco

Tyco TY-L Series Bedienungsanleitung