Husky AISLE SHIELD Bedienungsanleitung
AISLE SHIELD
INSTALLATION INSTRUCTIONS
6146 DENVER INDUSTRIAL PARK RD DENVER NC 28037
1-800-438-5629
www.h skyrackandwire.com 1
INSTALLATION OF OFFSET MOUNT
AISLE SHIELD
STEP 1: EYE BOLT ASSEMBLY
STEP 1: EYE BOLT ASSEMBLYSTEP 1: EYE BOLT ASSEMBLY
STEP 1: EYE BOLT ASSEMBLY
HARDWARE REQUIRED:
FOR 4’ AND 5’ TALL PANELS SIX (6) EYE BOLTS
ARE REQUIRED PER PANEL.
FOR 3’ TALL PANELS FOUR (4) EYE BOLTS ARE
REQUIRED PER PANEL.
•
TAKE ONE OF EACH EYE BOLT, 3 8” REGULAR
NUT, 3 8” PLAIN WASHER, 3 8” LOCK
TAKE ONE OF EACH EYE BOLT, 3 8” REGULAR
NUT, 3 8” PLAIN WASHER, 3 8” LOCK
WASHER AND 3 8” NYLOK NUT.
•INSERT REGULAR NUT, PLAIN WASHER, LOCK
WASHER AND NYLOCK NUT RESPECTIVLEY IN
THAT ORDER AS SHOWN IN THE EYEBOLT
PICTURE TO THE LEFT.
•MEASURE DESIRED OFFSET DISTANCE USING
TAPE MEASURE. MEASURE FROM BOTTOM
OF THE LOCK WASHER TO CENTER OF THE
EYE BOLT. USE WRENCH TO TURN THE
NYLOCK NUT TO ACHIEVE DESIRED OFFSET.
OFFSET
2
INSTALLATION OF OFFSET MOUNT
AISLE SHIELD
STEP 2: ATTACH PANEL TO THE RACK
STEP 2: ATTACH PANEL TO THE RACKSTEP 2: ATTACH PANEL TO THE RACK
STEP 2: ATTACH PANEL TO THE RACK
•AS SHOWN IN THE PICTURE, INSERT ALL EYE
BOLTS ONTO THE PANEL AT THE JUNCTION OF
THE UPPER CURVE OF THE REINFORCING FLUTE
AND THE UPPERMOST OF THE THREE WIRES.
THE EYEBOLT MUST SIT UNDERNEATH THE
HORIZONTAL WIRE, AND THE GAP IN THE EYE
BOLT MUST FACE OUTWARD FROM THE PANEL.
•WITH ONE PERSON ON EACH END OF THE
PANEL, LIFT THE PANEL TO ATTACH TO THE RACK
POST.
PANEL, LIFT THE PANEL TO ATTACH TO THE RACK
POST.
•INSERT THE TOP EYE BOLTS IN THE DESIRED
HOLES ON THE RACK POST. KEEPING THE LOCK
WASHER AND NYLOCK NUT INSIDE OF THE RACK
POST.
•HAND TIGHTEN THE REGULAR NUT FROM THE
OUTSIDE, AGAINST THE RACK POST.
•COMPLETE ASSEMBLY OF ALL EYE BOLTS TO THE
RACK POST.
•ONCE ALL EYE BOLTS ARE ATTACHED, TIGHTEN
THE NUTS USING A WRENCH.
3
INSTALLATION OF FLUSH MOUNT AISLE
SHIELD
STEP 1: ATTACH FLAT BRACKETS TO THE PANEL
STEP 1: ATTACH FLAT BRACKETS TO THE PANELSTEP 1: ATTACH FLAT BRACKETS TO THE PANEL
STEP 1: ATTACH FLAT BRACKETS TO THE PANEL
•MATERIAL REQUIRED:
FOR 4’ AND 5’ TALL PANELS SIX (6) SETS OF
HARDWARE IS REQUIRED PER PANEL.
FOR 3’ TALL PANELS FOUR (4) SETS OF
HARDWARE IS REQUIRED PER PANEL.
–FLAT BRACKET 1 ¾” WIDE X 5 ½” LONG
WITH TWO HOLES
–
SLOTTED BACK
-
UP PLATE
FLAT BRACKET
–
SLOTTED BACK
-
UP PLATE
–¼” X ¾” HEX HEAD BOLT & ¼” NUT
–3 8” X 2” CARRAIGE BOLT & 3 8” NUT
–1” SPACER
•AS SHOWN IN THE PICTURE, ATTACH THE FLAT
BRACKET TO THE PANEL USING BACK-UP PLATE
AND ¼” BOLT AND NUT
•ATTACH ALL PROVIDED FLAT BRACKETS TO THE
PANEL AT THE REINFORCING FLUTES OF THE
PANEL.
BACK UP PLATE
4
INSTALLATION OF FLUSH MOUNT AISLE
SHIELD
STEP 2: ATTACH PANEL TO THE RACK
STEP 2: ATTACH PANEL TO THE RACKSTEP 2: ATTACH PANEL TO THE RACK
STEP 2: ATTACH PANEL TO THE RACK
•ATTACH THE 3 8” CARRIAGE BOLT TO THE
OTHER END OF THE FLAT BRACKET. USE 1”
PLASTIC SPACER BETWEEN THE BRACKET AND
RACK POST.
•ATTACH 3 8” BOLTS TO ALL OF THE FLAT
BRACKETS PROVIDED.
•WITH ONE PERSON ON EACH END OF THE
PANEL, LIFT THE PANEL TO ATTACH TO THE RACK
1” SPACER
PANEL, LIFT THE PANEL TO ATTACH TO THE RACK
POST.
•INSERT THE HEAD OF THE BOLT THROUGH THE
UPRIGHT POST HOLE.
•TIGHTEN THE 3 8” NUT USING A WRENCH.
5
INSTALLATION OF EXTENDED AISLE SHIELD
STEP 1: ATTACH ANGLE BRACKET AND FLAT BAR
STEP 1: ATTACH ANGLE BRACKET AND FLAT BARSTEP 1: ATTACH ANGLE BRACKET AND FLAT BAR
STEP 1: ATTACH ANGLE BRACKET AND FLAT BAR
ANGLE
BRACKET
FLAT BAR
ATTACH ANGLE BRACKETS TO THE AISLE SHIELD
PANEL AT THE TOP REINFORCING FLUTES ON EACH
SIDE USING ¼” BOLT AND NUT AS SHOWN IN THE
ABOVE PICTURE. DO THIS FOR BOTH SIDES OF THE
PANEL.
ATTACH FLAT BARS TO THE ANGLE BRACKETS ON
EACH SIDE USING 3 8” BOLT AND NUT AS SHOWN
IN THE PICTURE ABOVE.
6
INSTALLATION OF EXTENDED AISLE
SHIELD
STEP 2: ATTACH FLAT BAR TO THE RACK POST
STEP 2: ATTACH FLAT BAR TO THE RACK POSTSTEP 2: ATTACH FLAT BAR TO THE RACK POST
STEP 2: ATTACH FLAT BAR TO THE RACK POST
•ATTACH THE OTHER END OF THE FLAT BAR TO
THE RACK POST USING 3 8” BOLT AND NUT.
•NOTE: FOR FLUSH MOUNT RACK GUARD, THE
FLAT BAR IS ATTACHED TO THE POST THAT IS
AWAY FROM THE AISLE SHIELD PANEL. FOR
OFFSET MOUNT AISLE SHIELD, THE FLAT BAR IS
ATTACHED TO THE NEAREST POST TO THE AISLE
SHIELD PANEL.
7
B13 8
Inhaltsverzeichnis
Andere Husky Lagerung Handbücher
Husky
Husky HOTC4116B12S Bedienungsanleitung
Husky
Husky G3002T-US Bedienungsanleitung
Husky
Husky 1000 000 000 Bedienungsanleitung
Husky
Husky GS05403-1D Bedienungsanleitung
Husky
Husky MR482478W5-R Bedienungsanleitung
Husky
Husky MRTP481886W6B Bedienungsanleitung
Husky
Husky H46MWC9XD-TL Bedienungsanleitung
Husky
Husky HBR652454W3 Bedienungsanleitung
Husky
Husky HOTC5623BB2S Bedienungsanleitung
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung