Husqvarna 235 Montageanleitung

Model 225, 232, 235

Basic adjustment ofcarburetor (CARB)

After replacing the needles or complete carburetor on a CARB certified product, a basic

edjustment must be carried out as described below in order to meet the CARB -requirements.

After replacement of completecarburetor

1. Check that the H cap is adjusted to its richest setting. (Turned counterclockwise to stop.)

The cap is not fixed to the needle, but can be rotated independently.

Do not adjust the L needle. This needle is set at the factory and the cap is already fitted.

2. Fit 4 trimmer fines, diameter 3.3 mm (0.13 inch) to a Trimmy Fix.

(Trimmy Fix M10, 531 00 38-69, for 225 and 232. Trimmy Fix M12, 502 13 87-02, for 235.)

It may be necessary to drill out the holes in the Trimmy Fix to make it easier to fit the

trimmer fines.

3. Cut the trimmer fines to correct lenght (measured from the outer edge of the Trimmy Fix):

225 145 mm (5.7 inches)

232: 155 mm (6.1 inches)

235: 170 mm (6.7 inches)

Fit the Trimmy Fix on the machine. Note! For 235 the sprayguard must be removed. Be

aware of the fines.

4. Start the engine. If necessary, adjust the idle speed with the T -screw.

5. Using a narrow blade screwdriver inserted through the hole in the cap (max. blade width 2

mm, 0.08 inch) adjust the H needle to give a top speed of 8400 ±200 rpm.

6. Let the engine run for 2-3 minutes until warm.

7. Check that the top speed is still 8400

200 rpm. Readjust if necessary.

8. Check that the H cap is still adjusted to its richest setting. (Turned counterclockwise to stop).

9. Gently knock the H cap into position. Use a 5 mm (0.2 inch) mandrel or the locking pin for

the gear, 502 02 61-03.

This is a basic carburetor adjustment. Further fine adjustments, within the limits the caps

allows, may be necessary to achieve optimum performance. See the operator's manual.

04-96 1 (5) SSG04006.PDF

After replacement of only H-needle

1. Adjust the L-needle to its richest setting. (Toured counterclockwise to stop.)

2. Take off the cap from the H -needle using e. g. a pair of cutting pliers and unscrew the

needle.

3. Screw the new H-needle to the bottom and then turn it counterclockwise 1/2 turn.

4. Press a new H-cap on the H-needle to the first stop, which means that the cap is not fixed to

the needle, but can be rotated separately.

5. Adjust the H-cap to the richest position without turning the needle. (Turned

counterclockwise to stop.)

6. Fit 4 trimmer fines, diameter 3.3 mm (0.13 inch) to a Trimmy Fix.

(Trimmy Fix M10, 531 00 38-69, for 225 and 232. Trimmy Fix M12, 502 13 87-02, for 235.)

It may be necessary to drill out the holes in the Trimmy Fix to make it easier to fit the

trimmer fines.

7. Cut the trimmer fines to correct lenght (measured from the outer edge of the Trimmy Fix):

225: 145 mm (5.7 inches)

232: 155 mm (6.1 inches)

235: 170 mm (6.7 inches)

Fit the Trimmy Fix on the machine. Note! For 235 the sprayguard must be removed. Be

aware of the fines.

8. Start the engine. If necessary, adjust the idle speed with the T -screw.

9. Using a narrow blade screwdriver inserted through the hole in the cap (max. blade width 2

mm, 0.08 inch) adjust the H needle to give a top speed of 8400 ±200 rpm.

10. Let the engine run for 2-3 minutes until warm.

11. Check that the top speed is still 8400

200 rpm. Readjust if necessary.

12 Check that the H cap is still adjusted to its richest setting. (Turned counterclockwise to

stop).

13. Gently knock the H cap into position. Use a 5 mm (0.2 inch) mandrel or the locking pin for

the gear, 502 02 61-03.

This is a basic carburetor adjustment. Further fine adjustments, within the limits the caps

allows, may be necessary to achieve optimum performance. See the operator's manual.

04-96 2 (5) SSG04006.PDF

After replacement of only L-needle

1. Adjust the H-needle to the leanest position. (Turned clockwise to stop.)

2. Take off the cap from the L -needle using e. g. a pair of cutting pliers and unscrew the

needle.

3. Screw the new L-needle to the bottom and then turn it counterclockwise 2 turns.

4. Press a new L-cap on the L-needle to the first stop, which means that the cap is not fixed

to the needle, but can be rotated separately.

5. Adjust the L-cap to the leanest position without turning the needle. (Turned clockwise to

stop.)

6. Start the engine and let it run on idle.

7. Using a narrow blade screwdriver inserted through the hole in the cap (max. blade width 2

mm, 0.08 inch) adjust the L -needle until highest possible idlespeed is achieved.

8. Check that the L-cap is still adjusted to its leanest position. (Turned clockwise to stop.)

9. Gently knock the L-cap into position. Use a 5 mm (0.2 inch) mandrel or the locking pin for

the gear, 502 02 61-03.

This is a basic carburetor adjustment. Further fine adjustments, within the limits the caps

allows, may be necessary to achieve optimum performance. See the operator's manual.

04-96 3 (5) SSG04006.PDF

After replacement of both H-needle and L-needle

1. Take off the caps from both needles using e. g. a pair of cutting pliers and unscrew the

needles.

2. Screw the new L-needle to the bottom and then turn it counterclockwise 2 turns.

Screw the new H-needle to the bottom and then turn it counterclockwise 1/2 turns.

3. Press new caps on the needles to the first stop, which means that the caps are not fixed

to the needles, but can be rotated separately.

4. Adjust the L-cap to the leanest position without turning the needle. (Turned clockwise to stop.)

5. Start the engine and let it run on idle.

6. Using a narrow blade screwdriver inserted through the hole in the cap (max. blade width 2

mm, 0.08 inch) adjust the L -needle until highest possible idlespeed is achieved.

7. Check that the L-cap is still adjusted to its leanest position. (Turned clockwise to stop.)

8. Gently knock the L-cap into position. Use a 5 mm (0.2 inch) mandrel or the locking pin for

the gear, 502 02 61-03. Turn the L -needle to the richest position. (Turned

counterclockwise to stop.)

9. Adjust the H-cap to the richest position without turning the needle. (Turned

counterclockwise to stop.)

10. Fit 4 trimmer fines, diameter 3.3 mm (0.13 inch) to a Trimmy Fix.

(Trimmy Fix M10, 531 00 38-69, for 225 and 232. Trimmy Fix M12, 502 13 87-02, for 235.)

It may be necessary to drill out the holes in the Trimmy Fix to make it easier to fit the

trimmer fines.

11. Cut the trimmer fines to correct lenght (measured from the outer edge of the Trimmy Fix):

225: 145 mm (5.7 inches)

232: 155 mm (6.1 inches)

235: 170 mm (6.7 inches)

Fit the Trimmy Fix on the machine. Note! For 235 the sprayguard must be removed. Be

aware of the fines.

04-96 4 (5) SSG04006.PDF

12. Start the engine.

13. Using a narrow blade screwdriver inserted through the hole in the cap (max. blade width 2

mm, 0.08 inch) adjust the H needle to giv e a top speed of 8400 ±200 rpm.

14. Let the engine run for 2-3 minutes until warm .

15. Check that the top speed is still 8400

200 rpm. Readjust if necessary.

16. Check that the H cap is still adjusted to its richest setting. (Turned counterclockwise to

stop).

17. Gently knock the H cap into position. Use a 5 mm (0.2 inch) mandrel or the locking pin for

the gear, 502 02 61-03.

This is a basic carburetor adjustment. Further fine adjustments, within the limits the caps

allows, may be necessary to achieve optimum performance. See the operator's manual.

04-96 5 (5) SSG04006.PDF

Andere Handbücher für 235

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Husqvarna Trimmer Handbücher

Husqvarna

Husqvarna 322HD60 Bedienungsanleitung

Husqvarna

Husqvarna 520iHE3 Bedienungsanleitung

Husqvarna

Husqvarna 129C Bedienungsanleitung

Husqvarna

Husqvarna 253RJ Bedienungsanleitung

Husqvarna

Husqvarna 326E X-series Bedienungsanleitung

Husqvarna

Husqvarna 324L X-series Bedienungsanleitung

Husqvarna

Husqvarna 325HE3 X-series Bedienungsanleitung

Husqvarna

Husqvarna 129DJx Bedienungsanleitung

Husqvarna

Husqvarna 123HD60 Gebrauchsanweisung

Husqvarna

Husqvarna HA200 Bedienungsanleitung

Husqvarna

Husqvarna 326RJX Series Bedienungsanleitung

Husqvarna

Husqvarna 326EX-series Bedienungsanleitung

Husqvarna

Husqvarna 227R/RD Bedienungsanleitung

Husqvarna

Husqvarna 324R X-Series Bedienungsanleitung

Husqvarna

Husqvarna J-handle barrier 536LiLX Bedienungsanleitung

Husqvarna

Husqvarna 536LiL Gebrauchsanweisung

Husqvarna

Husqvarna 226K Bedienungsanleitung

Husqvarna

Husqvarna 343F Bedienungsanleitung

Husqvarna

Husqvarna 327RD X-series Bedienungsanleitung

Husqvarna

Husqvarna 227R Bedienungsanleitung

Husqvarna

Husqvarna 124C Bedienungsanleitung

Husqvarna

Husqvarna 970 55 16-02 Bedienungsanleitung

Husqvarna

Husqvarna 543RB Bedienungsanleitung

Husqvarna

Husqvarna 123L Bedienungsanleitung

Beliebte Trimmer Handbücher anderer Marken

MTD

MTD HT 51 E Bedienungsanleitung

McCulloch

McCulloch T22 LS Bedienungsanleitung

COCKRAFT

COCKRAFT PRO HL36-S Bedienungsanleitung

Grizzly

Grizzly CT 1800 Li Bedienungsanleitung

Peco

Peco Z Trimmer ZT-3000 Bedienungsanleitung

Solo

Solo 116 Bedienungsanleitung

Stiga

Stiga ST 1200 Bedienungsanleitung

Echo

Echo GT-225 - 10-09 Bedienungsanleitung

RedMax

RedMax BT17 Bedienungsanleitung

GreenWorks

GreenWorks STA806 Bedienungsanleitung

Parkside

Parkside PHSL 900 A3 Bedienungsanleitung

Gardeo

Gardeo PRO GPTHT2560 Bedienungsanleitung

Park

Park DT-810870 Bedienungsanleitung

Worx

Worx WG209 Bedienungsanleitung

Gardenline

Gardenline 43671/HTKS26 Bedienungsanleitung

Makita

Makita 3710 Bedienungsanleitung

Champion

Champion 100683 Bedienungsanleitung

Stihl

Stihl FS 311 Bedienungsanleitung