Husqvarna 324HDA55X series Bedienungsanleitung

EEnn

nngg

ggll

llii

iiss

sshh

324HD

A55

X-series

Oper

ator

′

s manual

Please r

ead the operator’s manual carefully and make sure you

understand the instructions before using the machine.

–

English

KEY

O SYMBOLS

Symbols

ARNING! Incorrect or careless use of a

hedge trimmer can turn it into a dangerous

tool that can cause serious or even fatal

injury. It is extremely important that you

read and understand the contents of this

operator’s manual.

Please read the operator’s manual carefully

and make sure you understand the

instructions before using the machine.

Always wear:

• Approved hearing protection

• Protective goggles or a visor

This product is in accordance with applicable

EC directives.

Cutting tool. Do not touch the tool without

ﬁrst switching off the engine.

This machine is not electrically insulated.

If the machine touches or comes close to

high-voltage power lines it could lead to

death or serious bodily injury. Electricity can

jump from one point to another by arcing.

The higher the voltage, the greater the

distance electricity can jump. Electricity can

also travel through branches and other

objects, especially if they are wet. Always

keep a distance of at least 10 m between the machine and

high-voltage power lines and/or any objects that are touching

them. If have to work within this safe distance you should

always contact the relevant power company to make sure the

power is switched off before you start work.

This machine can be dangerous! The operator of the machine

must ensure, while working, that no persons or animals come

closer than 15 metres.

Arrows which show limits for handle

positioning.

Always wear approved protective gloves.

Wear sturdy, non-slip boots.

Noise emission to the environment according

to the European Community’s Directive. The

machine’s emission is speciﬁed in chapter

Technical data and on label.

Other symbols/decals on the mac

hine refer to special

certiﬁcation requirements for certain markets.

Switch off the engine by moving the stop

switch to the STOP position before carrying

out any checks or maintenance.

Always wear approved protective gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be worn.

English

–

CONTENTS

Contents

Note the f

ollowing before starting:

Please read the oper

ator’s manual carefully.

Long-term exposure to noise can result in permanent hearing

impairment. So always use approved hearing protection.

KEY

TO SYMBOLS

Symbols

....................................................................... 2

CONTENTS

Contents

...................................................................... 3

Note the following before starting: ................................ 3

INTR

ODUCTION

Dear Customer

, ............................................................ 4

WHA

T IS WHAT?

What is what?

.............................................................. 5

GENERAL SAFETY PRECA

UTIONS

Impor

tant ...................................................................... 6

Personal protective equipment ..................................... 6

Machine

′

s safety equipment ........................................ 7

ASSEMBL

Fitting the hand guard and loop handle

....................... 10

Fitting the cutting head ................................................ 10

FUEL HANDLING

Fuel handling

............................................................... 11

Fuel .............................................................................. 11

ARTING AND STOPPING

Chec

k before starting ................................................... 13

Starting and stopping ................................................... 13

ORKING TECHNIQUES

Gener

al working instructions ....................................... 15

MAINTENANCE

Carb

urettor ................................................................... 17

Mufﬂer .......................................................................... 17

Cooling system ............................................................ 18

Spark plug .................................................................... 18

Air ﬁlter ......................................................................... 18

Gear housing ............................................................... 19

Cleaning and lubrication .............................................. 19

Maintenance schedule ................................................. 20

TECHNICAL D

ATA

echnical data .............................................................. 21

EC-declaration of conformity (Applies to Europe only) . 22

ARNING! Under no circumstances may the

design of the machine be modiﬁed without

the permission of the manufacturer. Always

use genuine accessories. Non-authorized

modiﬁcations and/or accessories can result

in serious personal injury or the death of the

operator or others.

ARNING! Incorrect or careless use of a

hedge trimmer can turn it into a dangerous

tool that can cause serious or even fatal

injury. It is extremely important that you read

and understand the contents of this

operator’s manual.

–

English

INTR

ODUCTION

Dear Customer

Cong

ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the

Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. The

location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. During the

more than 300 years of beeing, the Husqvarna factory has produced a lot of different products, from wood stoves to modern kitchen

appliances, sewing machines, bicycles, motorcycles etc. In 1956, the ﬁrst motor driven lawn mowers appeared, followed by chain

saws in 1959, and it is within this area Husqvarna is working today.

Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our highest priority.

The business concept is to develop, manufacture and market motor driven products for forestry and gardening as well as for

building and construction industry. Husqvarna

′

s aim is also to be in the front edge according to ergonomics, usability, security and

environmental protection. That is the reason why we have developed many different features to provide our products within these

areas.

We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very long time to

come. The purchase of one of our products gives you access to professional help with repairs and service whenever this may be

necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the address of your nearest service

workshop.

It is our wish that you will be satisﬁed with your product and that it will be your companion for a long time. Think of this operator

′

manual as a valuable document. By following its

′

content (using, service, maintenance etc) the life span and the second-hand value

of the machine can be extended. If you will sell this machine, make sure that the buyer will get the operator

′

s manual.

Thank you for using a Husqvarna product.

Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and

appearance of products without prior notice.

English

–

WHA

T IS

WHA

What is what?

13 14

Cutter

2 Grease nipple and plug for ﬁlling lubricant.

3 Bevel gear

4 Blade guard

5 Shaft

6 Front handle

7 Throttle control

8 Stop switch

9 Throttle lock

10 Cylinder cover

11 Starter handle

12 Fuel tank

13 Choke control

14 Air purge

15 Air ﬁlter cover.

16 Clutch cover

17 Hand guard mounting screw

18 Angle adjustment knob

19 Hand guard

20 Combination spanner

21 Operator

′

s manual

22 Transport guard

23 Allen key

–

English

GENERAL SAFETY PRECA

UTIONS

Impor

tant

Personal protective equipment

HEARING PR

OTECTION

Wear hearing protection that provides adequate noise

reduction.

EYE PROTECTION

Always wear approved eye protection. If you use a visor then

you must also wear approved protective goggles. Approved

protective goggles must comply with standard ANSI Z87.1 in

the USA or EN 166 in EU countries.

GLOVES

Gloves should be worn when necessary, e.g., when ﬁtting

cutting attachments.

BOOTS

Wear sturdy, non-slip boots.

CLOTHING

Wear clothes made of a strong fabric and avoid loose clothing

that can catch on twigs and branches. Always wear heavy,

long pants. Do not wear jewellery, shorts sandals or go

barefoot. Secure hair so it is above shoulder level.

FIRST AID KIT

Always have a ﬁrst aid kit nearby.

IMPORTANT!

The machine is only designed for cutting branches and

twigs.

Never use a machine that has been modiﬁed in any way

from its original speciﬁcation.

Never use the machine if you are tired, if you have drunk

alcohol, or if you are taking medication that could affect your

vision, your judgement or your co-ordination.

Wear personal protective equipment. See instructions

under the heading Personal protective equipment.

Never use the machine in extreme weather conditions such

as severe cold, very hot and/or humid climates.

Never use a machine that is faulty. Carry out the checks,

maintenance and service instructions described in this

manual. Some maintenance and service measures must be

carried out by trained and qualiﬁed specialists. See

instructions under the heading Maintenance.

All covers and guards must be ﬁtted before starting. Ensure

that the spark plug cap and ignition lead are undamaged to

avoid the risk of electric shock.

ARNING! Running an engine in a conﬁned

or badly ventilated area can result in death

due to asphyxiation or carbon monoxide

poisoning.

ARNING! Faulty blades can increase the

risk of accidents.

IMPOR

TANT!

Incorrect or careless use of a hedge trimmer can turn it into

a dangerous tool that can cause serious or even fatal injury.

It is extremely important that you read and understand the

contents of this operator’s manual.

You must use approved personal protective equipment

whenever you use the machine. Personal protective

equipment cannot eliminate the risk of injury but it will

reduce the degree of injury if an accident does happen. Ask

your dealer for help in choosing the right equipment.

ARNING! Listen out for warning signals or

shouts when you are wearing hearing

protection. Always remove your hearing

protection as soon as the engine stops.

English

–

GENERAL SAFETY PRECA

UTIONS

Mac

hine

′′′′

s safety equipment

This section descr

ibes the machine

′

s safety equipment, its

purpose, and how checks and maintenance should be carried

out to ensure that it operates correctly. See the ”What is

what?” section to locate where this equipment is positioned

on your machine.

The life span of the machine can be reduced and the risk of

accidents can increase if machine maintenance is not carried

out correctly and if service and/or repairs are not carried out

professionally. If you need further information please contact

your nearest service workshop.

Thr

ottle lock

The throttle loc

k is designed to prevent accidental operation

of the throttle control. When you press the lock (A) (i.e. when

you grasp the handle) it releases the throttle control (B).

When you release the handle the throttle control and the

throttle lock both move back to their original positions. This

movement is controlled by two independent return springs.

This arrangement means that the throttle control is

automatically locked at the idle setting.

Make sure the throttle control is locked at the idle setting

when the throttle lock is released.

Press the throttle lock and make sure it returns to its original

position when you release it.

Check that the throttle control and throttle lock move freely

and that the return springs work properly.

See instructions under the heading Start. Start the hedge

trimmer and apply full throttle. Release the throttle trigger and

check that the blades stop and remain stationary. If the blades

move when the throttle trigger is in the idle position then the

carburettor idle setting must be adjusted. See instructions

under the heading Maintenance.

Stop s

witch

Use the stop s

witch to switch off the engine.

Start the engine and make sure the engine stops when you

move the stop switch to the stop setting.

Hand guar

The hand guard pre

vents hands from coming into contact with

the moving blades, for example, if the operator loses grip on

the front handle.

Check that the hand guard is ﬁtted correctly.

Check that the hand guard is undamaged.

IMPORTANT!

All servicing and repair work on the machine requires

special training. This is especially true of the machine

′

safety equipment. If your machine fails any of the checks

described below you must contact your service agent.

When you buy any of our products we guarantee the

availability of professional repairs and service. If the retailer

who sells your machine is not a servicing dealer, ask him for

the address of your nearest service agent.

ARNING! Never use a machine with faulty

safety equipment. The machine’s safety

equipment must be checked and maintained

as described in this section. If your machine

fails any of these checks contact your

service agent to get it repaired.

–

English

GENERAL SAFETY PRECA

UTIONS

Vibration damping system

our machine is equipped with a vibration damping system

that is designed to minimize vibration and make operation

easier.

The machine

′

s vibration damping system reduces the transfer

of vibration between the engine unit/cutting equipment and

the machine

′

s handle unit.

Regularly check the vibration damping units for cracks or

deformation. Check that the vibration damping element is

undamaged and securely attached.

Mufﬂ

The m

ufﬂer is designed to keep noise levels to a minimum

and to direct exhaust fumes away from the user.

A mufﬂer ﬁtted with a catalytic converter is also designed to

reduce harmful exhaust gases.

In countries that have a warm and dry climate there is a

signiﬁcant risk of ﬁre. We therefore ﬁt certain mufﬂers with a

spark arrestor mesh. Check whether the mufﬂer on your

machine is ﬁtted with this kind of mesh.

For mufﬂers it is very important that you follow the instructions

on checking, maintaining and servicing your machine.

Never use a machine that has a faulty mufﬂer.

Regularly check that the mufﬂer is securely attached to the

machine.

If the mufﬂer on your machine is ﬁtted with a spark arrestor

mesh this must be cleaned regularly. A blocked mesh will

cause the engine to overheat and may lead to serious

damage.

WARNING! Overexposure to vibration can

lead to circulatory damage or nerve damage

in people who have impaired circulation.

Contact your doctor if you experience

symptoms of overexposure to vibration.

Such symptoms include numbness, loss of

feeling, tingling, pricking, pain, loss of

strength, changes in skin colour or

condition.These symptoms normally appear

in the ﬁngers, hands or wrists. The risk

increases at low temperatures.

WARNING! Mufﬂers ﬁtted with catalytic

converters get very hot during use and

remain so for some time after stopping.This

also applies at idle speed. Contact can result

in burns to the skin. Remember the risk of

ﬁre!

WARNING! The inside of the mufﬂer contain

chemicals that may be carcinogenic. Avoid

contact with these elements in the event of a

damaged mufﬂer.

WARNING! Bear in mind that:

The exhaust fumes from the engine are hot

and may contain sparks which can start a

ﬁre. Never start the machine indoors or near

combustible material!

English – 9

GENERAL SAFETY PRECAUTIONS

Blades

To ensure good cutting results it is important that the contact

pressure between the blades is correct. The contact pressure

is adjusted by turning the screws on the underside of the bar

clockwise as far as they will go. Then turn the screws

anticlockwise a 1/4 turn. Lock the screws using the locking nut

on the top of the bar. Check that the screws are loose enough

to allow the washers under the screw heads to slide sideways.

When the blades are correctly adjusted the play between the

blades should be 0,2–0,4 mm, measured at the screws.

The edges of the blades are too hard to be ﬁled. Dull blades

should be sharpened using a grinder.

Replace the blades if they are bent or damaged.

Blade guard

The blade guard (A) is intended to protect against any part of

the body coming into contact with the blades (B).

Check that the blade guard is not damaged or distorted.

Replace the blade guard if it is bent or damaged.

Gear housing

The gear housing gets hot when the machine has been in

use. To avoid burning yourself do not touch the gear housing.

10 – English

ASSEMBLY

Fitting the hand guard and loop

handle

1 Assemble the hand guard and loop handle by screwing

them together. Take care to align the holes in both parts.

2 Slide the loop handle and hand guard onto the shaft.

3 Slide the spacer into the slot in the loop handle.

4 Fit the nut and screw. Do not overtighten.

5 Now make a ﬁnal adjustment to give yourself a

comfortable working position. Tighten the screw.

CAUTION! The loop handle and hand guard must not be

ﬁtted behind the arrow marked on the shaft.

Fitting the cutting head

It is important that the hedge trimmer is laid on a ﬂat surface

when you ﬁt the cutting head. Otherwise the cutting head may

not be ﬁtted straight.

1 Fit the cutting head to the shaft. CAUTION! Make sure the

drive shaft inside the shaft engages with the recess in the

cutting head.

2 Tighten the lower screw ﬁrst, then the upper screw.

Andere Handbücher für 324HDA55X series

Inhaltsverzeichnis

Andere Husqvarna Trimmer Handbücher

Husqvarna

Husqvarna 520iLX Bedienungsanleitung

Husqvarna

Husqvarna ECA308 Bedienungsanleitung

Husqvarna

Husqvarna HVT52 Bedienungsanleitung

Husqvarna

Husqvarna 322HD60 Bedienungsanleitung

Husqvarna

Husqvarna 326HDA55X-Series, 326HE3X-Seri Bedienungsanleitung

Husqvarna

Husqvarna 533RS Bedienungsanleitung

Husqvarna

Husqvarna 327HDA65 Series Bedienungsanleitung

Husqvarna

Husqvarna 323HD60 Bedienungsanleitung

Husqvarna

Husqvarna 333R Mark II Bedienungsanleitung

Husqvarna

Husqvarna Aspire T28-P4A Bedienungsanleitung

Husqvarna

Husqvarna 122c SERIES Bedienungsanleitung

Husqvarna

Husqvarna 129C Bedienungsanleitung

Husqvarna

Husqvarna 143R-II Bedienungsanleitung

Husqvarna

Husqvarna 224L Bedienungsanleitung

Husqvarna

Husqvarna 533RS Bedienungsanleitung

Husqvarna

Husqvarna 343R, 345RX, 343F, 345FX, 345F Gebrauchsanweisung

Husqvarna

Husqvarna 120iTK4-H Bedienungsanleitung

Husqvarna

Husqvarna 326EX series Bedienungsanleitung

Husqvarna

Husqvarna 524R Bedienungsanleitung

Husqvarna

Husqvarna 226R Gebrauchsanweisung

Husqvarna

Husqvarna 223L Bedienungsanleitung

Husqvarna

Husqvarna 326E X-series Bedienungsanleitung

Husqvarna

Husqvarna 325HE4 X-series Bedienungsanleitung

Husqvarna

Husqvarna 522HD60X Bedienungsanleitung

Beliebte Trimmer Handbücher anderer Marken

MTD

MTD HT 51 E Bedienungsanleitung

McCulloch

McCulloch T22 LS Bedienungsanleitung

COCKRAFT

COCKRAFT PRO HL36-S Bedienungsanleitung

Grizzly

Grizzly CT 1800 Li Bedienungsanleitung

Peco

Peco Z Trimmer ZT-3000 Bedienungsanleitung

Solo

Solo 116 Bedienungsanleitung

Stiga

Stiga ST 1200 Bedienungsanleitung

Echo

Echo GT-225 - 10-09 Bedienungsanleitung

RedMax

RedMax BT17 Bedienungsanleitung

Parkside

Parkside PHSL 900 A3 Bedienungsanleitung

Gardeo

Gardeo PRO GPTHT2560 Bedienungsanleitung

Park

Park DT-810870 Bedienungsanleitung

Worx

Worx WG209 Bedienungsanleitung

Gardenline

Gardenline 43671/HTKS26 Bedienungsanleitung

Makita

Makita 3710 Bedienungsanleitung

Champion

Champion 100683 Bedienungsanleitung

Stihl

Stihl FS 311 Bedienungsanleitung

Efco

Efco STARK 38 Handbuch