Husqvarna 325 L XT-Series Gebrauchsanweisung

Workshop manual

325L

English

1023 - 001 - 24.04.2019

Contents

1 Introduction

1.1 Document description............................................ 3

1.2 Target group...........................................................3

1.3 Revisions................................................................3

1.4 Safety..................................................................... 3

1.5 Servicing tools........................................................3

2 Safety

2.1 Safety definitions....................................................4

2.2 General safety instructions.....................................4

2.3 Symbols on the product......................................... 4

3 Prepare and do servicing on the product

3.1 Maintenance schedule........................................... 5

4 Servicing data

4.1 Servicing data ....................................................... 6

5 Servicing tools

5.1 Servicing tools........................................................9

6 Repair instructions

6.1 Product overview for repair instructions............... 11

6.2 To clean and examine the product parts..............11

6.3 To install the loop handle..................................... 11

6.4 To install the cutting attachment guard................ 12

6.5 To attach and remove the trimmer head.............. 12

6.6 Trimmer line replacement.................................... 13

6.7 Starter.................................................................. 14

6.8 Muffler.................................................................. 16

6.9 Air filter................................................................. 16

6.10 Flywheel............................................................. 17

6.11 Ignition system................................................... 18

6.12 Carburetor.......................................................... 22

6.13 Handle and throttle trigger..................................24

6.14 Centrifugal clutch............................................... 25

6.15 Cylinder and piston............................................ 26

6.16 Crankshaft and crankcase................................. 29

6.17 Fuel tank............................................................ 32

7 Troubleshooting

7.1 Troubleshooting................................................... 33

8 Technical data

8.1 Technical data......................................................36

21023 - 001 - 24.04.2019

1 Introduction

1.1 Document description

This manual gives a full description of how to do

maintenance and repair on the product. It also gives

safety instructions that the personnel must obey.

1.2 Target group

This manual is for personnel with a general knowledge

of how to do repair and do servicing. All personnel that

do repair or do servicing on the product must read and

understand the manual.

1.3 Revisions

Changes to the product can cause changes to the

maintenance work and spare parts. Separate

information is sent out for each change.

Read the manual together with all received information

about changes to maintenance and spare parts for the

product.

1.4 Safety

WARNING: All personnel that repair or do

servicing on the product must read and

understand the safety instructions in this

workshop manual.

1.5 Servicing tools

The manual gives information about necessary servicing

tools. Always use original tools from Husqvarna.

1023 - 001 - 24.04.2019 Introduction - 3

2 Safety

2.1 Safety definitions

Warnings, cautions and notes are used to point out

specially important parts of the manual.

WARNING: Used if there is a risk of injury or

death for the operator or bystanders if the

instructions in the manual are not obeyed.

CAUTION: Used if there is a risk of damage to

the product, other materials or the adjacent area

if the instructions in the manual are not obeyed.

Note: Used to give more information that is necessary in

a given situation.

2.2 General safety instructions

WARNING: Read the warning instructions that

follow before you use the product.

The service center that repairs the product must have

safety devices that obey local regulations. Warnings and

cautions are used to point out specially important parts

of the workshop manual.

2.3 Symbols on the product

WARNING! This product is dangerous.

Injury or death can occur to the operator

or bystanders if the product is not used

carefully and correctly. To prevent injury

to the operator or bystanders, read and

obey all safety instructions in the

operator's manual.

Please read the operator's manual

carefully and make sure that you

understand the instructions before use.

Use approved hearing protection. Use

approved eye protection.

Make sure that long hair is put up above

your shoulders.

the product can cause objects to eject,

which can cause injury.

Maximum speed of the output shaft.

50FT

15 m

50FT

15 m

Keep a minimum of 15 m / 50 ft distance

to persons and animals during operation

of the product.

Use only flexible trimmer line.

Do not use metal cutting elements.

The arrows show the limits for the position

of the handle.

Choke.

Refuelling.

Start/Stop switch.

Primer bulb.

The rating plate shows the

serial number. yyyy is the

production year, ww is the

production week and xxxxx

is the serial number.

yyyywwxxxxx

4 - Safety 1023 - 001 - 24.04.2019

3 Prepare and do servicing on the product

3.1 Maintenance schedule

Maintenance Before

operation After 40 h After 100

Clean the external surface. After each operation.

Clean the muffler, exhaust pipe and engine from leaves, dirt and unwanted lubri-

cant. After each operation.

Make sure that the cutting attachment does not move at idle speed. X

Do a check of the stop switch. X

Examine the cutting attachment and the cutting attachment guard for damages

and cracks. Replace if it is damaged. X

Examine the hand guard for damages and cracks. Replace if it is damaged. X

Do a check of the throttle trigger lockout and the throttle trigger. X

Examine the engine, the fuel tank and the fuel lines for leaks. X

Tighten nuts and screws. X

Examine the fuel filter for contamination and the fuel hose for cracks and other

defects. Replace if necessary. X

Examine the starter and the starter rope for damages. X

Clean the air filter. Replace if it is necessary. X

Examine the vibration damping units for damages and cracks. X

Examine the spark plug, refer to

To examine the spark plug on page 18

. X

Clean the cooling system. X

Clean the external surface of the carburetor and the area around it. X

Clean or replace the spark arrester mesh. X

Clean the inner surface of the fuel tank. X

Examine the spark plug. X

Make sure that the gear housing is filled with grease. X

1023 - 001 - 24.04.2019 Prepare and do servicing on the

product - 5

4 Servicing data

4.1 Servicing data

8 - 10 Nm

6 - 8 Nm

4 - 5 Nm

4 - 6 Nm

10 - 12 Nm

7 - 9 Nm

6 - 8 Nm

3 - 4 Nm

3.5 - 4.5 Nm

6 - 8 Nm

10 - 12 Nm 2.5 - 3.38 Nm

6 - Servicing data 1023 - 001 - 24.04.2019

3.38 - 4.5 Nm

2-3 Nm

4 - 6 Nm

1.5 - 2.5 Nm

3.5 - 4.5 Nm

1023 - 001 - 24.04.2019 Servicing data - 7

1 - 2 Nm

2 - 3 Nm

6 - 8 Nm

2 - 3 Nm

8 - Servicing data 1023 - 001 - 24.04.2019

5 Servicing tools

5.1 Servicing tools

11 129

1 2

5 6

13 14

0.3

0.5 mm

1716

1023 - 001 - 24.04.2019 Servicing tools - 9

Item Description Use for Article number

1 Air gap tool To measure the distance

between the flywheel and

the ignition module.

502 51 34-02

2 Piston assembly kit To assemble the piston. 521 54 83-01

3 Electrode gap tool To adjust the electrode gap. 502 51 91-01

4 Flywheel removal tool To remove the flywheel. 502 51 49-02

5 Rod assembly To remove/install piston pin. 521 53 35-01

6 Assembly pliers To repair the ignition cable. 502 50 06-01

7 Tachometer To measure engine speed. 502 71 14-01

8 T-handle Torx For Torx screws. 502 71 27-02

9 Test spark plug To do a check of the igni-

tion module.

502 71 13-01

10 Pressure gauge Pressure test. 531 03 06-23

11 Piston assembly kit To assemble the piston. 502 50 70-01

12 Carburetor tool To adjust the carburetor

settings.

585 07 17-01

13 Assembly fixture To hold the product in the

correct position.

502 51 03-01

14 Adjustment screwdriver To adjust the carburetor. 530 03 55-60

15 Detergent To clean the air filter. 583 87 69-01

16 Air filter oil To lubricate the air filter. 531 00 92-48

17 Gear housing grease To lubricate the bevel gear. 503 97 64-01

10 - Servicing tools 1023 - 001 - 24.04.2019

Andere Handbücher für 325 L XT-Series

Inhaltsverzeichnis

Andere Husqvarna Trimmer Handbücher

Husqvarna

Husqvarna 536LiHE3 Gebrauchsanweisung

Husqvarna

Husqvarna 325HDA55X-Series, 325HE3X-Series, 325HE4X-Series,... Bedienungsanleitung

Husqvarna

Husqvarna 522HS75X Bedienungsanleitung

Husqvarna

Husqvarna 124C Bedienungsanleitung

Husqvarna

Husqvarna 326LX SERIES Bedienungsanleitung

Husqvarna

Husqvarna 325HDA55X-Series, 325HE3X-Series, 325HE4X-Series,... Bedienungsanleitung

Husqvarna

Husqvarna 325HS75 X-series Bedienungsanleitung

Husqvarna

Husqvarna 324L X-series Bedienungsanleitung

Husqvarna

Husqvarna 12 RC Bedienungsanleitung

Husqvarna

Husqvarna 520iLX Bedienungsanleitung

Husqvarna

Husqvarna 122c SERIES Bedienungsanleitung

Husqvarna

Husqvarna 324L X-series Bedienungsanleitung

Husqvarna

Husqvarna 343F Bedienungsanleitung

Husqvarna

Husqvarna 215iHD45 Bedienungsanleitung

Husqvarna

Husqvarna RA-V Bedienungsanleitung

Husqvarna

Husqvarna 326HDA Bedienungsanleitung

Husqvarna

Husqvarna 120iTK4-H Bedienungsanleitung

Husqvarna

Husqvarna 543 RBX Bedienungsanleitung

Husqvarna

Husqvarna 535RX Bedienungsanleitung

Husqvarna

Husqvarna 327RJX series Bedienungsanleitung

Husqvarna

Husqvarna 323C Bedienungsanleitung

Husqvarna

Husqvarna 522iHD60 Bedienungsanleitung

Husqvarna

Husqvarna 143R-II Bedienungsanleitung

Husqvarna

Husqvarna 326EX series Bedienungsanleitung

Beliebte Trimmer Handbücher anderer Marken

MTD

MTD HT 51 E Bedienungsanleitung

McCulloch

McCulloch T22 LS Bedienungsanleitung

COCKRAFT

COCKRAFT PRO HL36-S Bedienungsanleitung

Grizzly

Grizzly CT 1800 Li Bedienungsanleitung

Peco

Peco Z Trimmer ZT-3000 Bedienungsanleitung

Solo

Solo 116 Bedienungsanleitung

Stiga

Stiga ST 1200 Bedienungsanleitung

Echo

Echo GT-225 - 10-09 Bedienungsanleitung

RedMax

RedMax BT17 Bedienungsanleitung

Parkside

Parkside PHSL 900 A3 Bedienungsanleitung

Gardeo

Gardeo PRO GPTHT2560 Bedienungsanleitung

Park

Park DT-810870 Bedienungsanleitung

Worx

Worx WG209 Bedienungsanleitung

Gardenline

Gardenline 43671/HTKS26 Bedienungsanleitung

Makita

Makita 3710 Bedienungsanleitung

Champion

Champion 100683 Bedienungsanleitung

Stihl

Stihl FS 311 Bedienungsanleitung

Efco

Efco STARK 38 Handbuch