HVS FP3500-T11 Bedienungsanleitung
1
FP3500-T11/FP3600-T11
Installation Guide
FP unit (1)
Installation Guide (1) (this manual) Warning/Caution Information (1)
Installation Gasket (1)(attached to the FP unit)
Installation Brackets (4/set, 1set) USB Cable Clamp(2)
This unit has been carefully packed, with special attention to quality. However, should
you find anything damaged or missing, please contact your local FP distributor
immediately.
An FP-3500T/3600T series unit needs the following software for operation. As FP user
manual, provided by PDF media, describes its details, download the manual below and
get the further information. Visit our website below and get both software and reference
manual. (URL:http://www.pro-face.com/otasuke/)
• Software : Mouse Emulation Software
• Manual : FP-3500T/3600T/3650T series User Manual
Caution
Be sure to read the “Warning/Caution Information” on the attached sheet before using
the product.
Package Contents
Required software/Reference manual
DISTRIBUTEU R C O NSEI L DEPUI S 1985
System
Email :
2 rue René Laennec 51500 Taissy France
Fax: 03 26 85 19 08, Tel : 03 26 82 49 29
Site web : www.hvssystem.com
Distribué par :
2
1Part Names
CDEFGH
Front View
Rear View
Bottom View
A,B
J
I
A: TFT Color LCD
Acts as a display monitor for your host.
B: Touch Panel
Allows you to switch screens or write data to
the host.
C: Input Terminal Block
Provides the input and ground terminals for a
power cable.
D: Setting Switch
By opening the cover, the Dip switches and
slide switch are seen. Each switch can set a
operation mode.
E:Analog RGB Connector
Connector for analog RGB interface
F: DVI-D Interface Connector
Connector for DVI-D interface
G: Serial Connector
Connector for serial (RS-232C) interface.
Used for sending touch panel data to the
host.
H: USB Connector (Type B)
Connector for USB interface. Used for
sending touch panel data to the host or used
as an upstream port for USB-HUB.
I: Front LED
Used to indicate the condition of the power
supply, a backlight burnout or image signal
input.
J: USB Connector (Type A)
Adownstream port for embedded USB-HUB
in conformity with USB2.0/1.1 standard,
which is used for connecting USB devices.
Connect the upstream port of the USB-HUB
(H:USB connector) to the Host PC for USB
connector use.
3
The Dip Switches and Slide Switch are located in the bottom of the FP unit. Only the
settings when the power supply is turned on is effective to the Dip Switches and the Slide
Switch. After changing the settings of the Dip Switches and the Slide Switch, be sure to
restart your FP unit
SW1
• SW1-2 Dip Switch SW1-2 is used to display or hide the OSD.
To hide the OSD, set the switch to ON. To display the OSD, set the switch to OFF.
The default setting is OFF. (OSD is displayed.)
SW2
2Dimensions
3Dip Switches and Slide Switch
Switch Setting
SW1-1 Reserved (Always OFF)
SW1-2 Display/Hide the OSD
SW1-3 Reserved (Always OFF)
SW1-4 Reserved (Always OFF
SW1-5 Reserved (Always OFF)
SW1-6 Reserved (Always OFF)
SW1-7 Reserved (Always OFF)
SW1-8 Reserved (Always OFF)
Switch Setting
Slide Switch is used to switch the data input/output (command
control) method on the touch panel between USB and RS-232C
(Serial). The default setting is RS-232C.
301[11.85]
227[8.94]
58[2.28]
317[12.48]
243[9.57]
317[12.48]
243[9.57]
8[0.31]
Top View
Front View (FP3500-T11) Side View
Unit: mm [in]
Front View (FP3600-T11)
Dip Switches(SW1)
Slide Switch(SW2)
Bottom View
ON
18
SW1
232
USB
4
Analog RGB Interface
Display Area (FP3500-T11)
Display Area (FP3600-T11)
4Interfaces
Input signal type Analog RGB
Input signal
characteristic Image signal : analog RGB
Synchronous signal :TTL level, negative true or positive true
Scanning type : non-interlace
Setting by OSD
(On Screen Display)
•CONTRAST
•H-POSITION
•H-size
•DIMMER(BACKLIGHT)
•ALL RESET (DEFAULT)
•BRIGHTNESS
•V-POSITION
•PHASE
•SHARPNESS
Size H Sync.
(kHz) V Sync.
(Hz) DotClock
(MHz) Screen Resolution Expansion
(H: Horizontal)(V: Vertical) Display
Resolution
640×350*1
*1. When the 350 pixel (vertical) signal setting is selected, 400 pixels, including 50
pixels at the top and at the bottom of the screen will be enlarged and displayed at 480
pixels (1.2times).
31.469 70.000 25.175 ×1.0 (H)
×1.2 (V)
640×420
640×400 31.469 70.000 25.175 640×480
640×400 24.827 56.420 21.053 640×480
640×480 31.469 59.992 25.175 ×1.0 640×480
720×350*1*2
*2. When you use this resolution, set “ON” for “720 × 400 Mode” in the OSD (On
Screen Display) “system settings”.
31.469 70.000 28.320 ×0.89 (H)
×1.2 (V) 640×420
720×400*131.469 70.000 28.320 640×480
Size H Sync.
(kHz) V Sync.
(Hz) DotClock
(MHz) Screen Resolution Expansion
(H: Horizontal)(V: Vertical) Display
Resolution
640×350*1
*1. When the 350 pixel (vertical) signal setting is selected, 400 pixels, including 50
pixels at the top and at the bottom of the screen will be enlarged and displayed at 600
pixels (1.5times).
31.469 70.000 25.175 ×1.25 (H)
×1.5 (V)
800×525
640×400 31.469 70.000 25.175 800×600
640×400 24.827 56.420 21.053 800×600
640×480 31.469 59.992 25.175 ×1.25 (H)
×1.5 (V)
800×600
640×480 35.000 66.670 30.240 800×600
640×480 37.861 72.810 31.500 800×600
720×350*1*2
*2. When you use this resolution, set “ON” for “720 × 400 Mode” in the OSD (On
Screen Display) “system settings”.
31.469 70.000 28.320 ×1.1 (H)
×1.5 (V) 800×525
720×400*231.469 70.000 28.320 800×600
800×600 35.156 56.250 36.000 ×1.0 800×600
800×600 37.879 60.317 40.000 800×600
5
Pin Assignments and Signal Names for Analog RGB
Connector.................. Mini Dsub 15 pin male
Connector set screw.. Inch type (4-40)
Cable......................... RGB cable manufactured by Pro-face.
FP-CV02-45 <4.5m> (VGA standard)
DVI-D Interface
Display Area (FP3500-T11)
Pin No Signal Name Condition Pin Location
1 Analog R R signal input
2 Analog G G signal input
3 Analog B B signal input
4 Reserved NC (spare for input)
5 Digital grounding Digital signal GND
6 Return R R signal GND
7 Return G G signal GND
8 Return B B signal GND
9 Reserved NC (spare for input)
10 Digital grounding Digital signal GND
11 Reserved NC (spare for input)
12 DDC DATA DDC Data
13 H. SYNC Horizontal synchronous signal input
14 V. SYNC Vertical synchronous signal input
15 DDC CLK DDC Clock
• If a cable other than the specified RGB cable is used, product
performance cannot be guaranteed due to the possibility of noise
interfering with the FP unit’s operation.
Input signal type DVI-D
Setting by OSD
(On Screen Display) •CONTRAST
•DIMMER(BACKLIGHT)
•ALL RESET (DEFAULT)
•BRIGHTNESS
•SHARPNESS
Size H Sync.
(kHz) V Sync.
(Hz) Dot Clock
(MHz) Screen Resolution Expansion
(H: Horizontal) (V: Vertical) Display
Resolution
640×400 31.469 70.000 25.175 ×1.0 (H)
×1.2 (V) 640×480
640×400 24.827 56.420 21.053
640×480 31.469 59.992 25.175 ×1.0
720×400*1
*1. When you use this resolution, set “ON” for “720 × 400 Mode” in the OSD (On
Screen Display) “system settings”.
31.469 70.000 28.320 ×0.89 (H)
×1.2 (V)
15
11
5
1
6
Display Area(FP3600-T11):
Pin Assignments and Signal Names for DVI-D
Connector.................. DVI-D 24-pin male
Connector set screw.. Inch type (4-40)
Cable......................... DVI-D cable manufactured by Pro-face.
FP-DV01-50 <5 m>
Serial Interface
Size H Sync.
(kHz) V Sync.
(Hz) DotClock
(MHz) Screen Resolution Expansion
(H: Horizontal) (V: Vertical) Display
Resolution
640×400 31.469 70.000 25.175 ×1.25 (H)
×1.5 (V)
800×600
640×400 24.827 56.420 21.053
640×480 31.469 59.992 25.175 ×1.25 (H)
×1.25 (V)
640×480 35.000 66.670 30.240
640×480 37.861 72.810 31.500
720×400*1
*1. When you use this resolution, set “ON” for “720 × 400 Mode” in the OSD (On
Screen Display) “system settings”.
31.469 70.000 28.320 ×1.1 (H)
×1.5 (V)
800×600 35.156 56.250 36.000 ×1.0
800×600 37.879 60.317 40.000
Pin No Signal Name Pin No Signal Name Pin Location
1 TMDS DATA2- 13 NC
2 TMDS DATA2+ 14 NC
3 TMDS DATA2 SHIELD 15 GND
4 NC 16 Hot Plug Detect
5 NC 17 TMDS DATA0-
6 DDC Clock 18 TMDS DATA0+
7 DDC Data 19 TMDS DATA0 SHIELD
8NC20NC
9 TMDS DATA1- 21 NC
10 TMDS DATA1+ 22 TMDS CLOCK
SHIELD
11 TMDS DATA1 SHIELD 23 TMDS CLOCK+
12 NC 24 TMDS CLOCK-
• If a cable other than the specified DVI-D cable is used, product
performance cannot be guaranteed due to the possibility of noise
interfering with the FP unit’s operation.
RS-232C Serial Interface
Baud rate : 9600 bps
Data length : 8 bits
Parity : None
Stop bit : 1
Flow Control: None
1
9
17
8
16
24
17
24
1
8
7
Pin Assignments and Signal Names for Serial Interface
*1 The CD, DTR, and DSR are connected together inside of the FP.
Connector.................. Dsub 9 pin female
Connector set screw.. Inch type (4-40)
Cable......................... SIO cable for FP manufactured by Pro-face.
FP61V-IS00-O
Concerning Signal Names
Signal names used for the serial interface on FP units are designed to match the pin order
used on most PC serial interfaces, so that a straight cable can be used to connect the two.
Therefore, connect each pin’s signal to the same signal name on the PC side.
For example, pin #2 ‘RD’ should be connected to the ‘RD’ input terminal on the PC’s
connector.
Refer to the FP-3500T/3600T/3650T series User Manual’s section “Cable Diagrams” for
each signal’s direction.
USB Interface (Type-B connector : Up-Stream Port)
Pin Assignments and Signal Names for USB Interface
Cable......................... USB cable manufactured by Pro-face.
FP-US00
Pin No. Signal Name Condition Pin Location
1 CD Carrier Detect*1
2 RD Receive Data (FP->Host)
3 SD Send Data (FP<-Host)
4 DTR Data Terminal Ready*1
5 GND Ground
6 DSR Data Set Ready*1
7 RS Request to Send (FP<-Host)
8 CS Clear to Send (FP->Host)
9 NC (Used internally)
Pin No. Signal Name Condition Pin Location
1 USB1-5V +5VIN
2 USBD1(-) USB data(-)
3 USBD1(+) USB data(+)
4 GND Ground
• If a cable other than the specified USB cable is used, product
performance cannot be guaranteed due to the possibility of noise
interfering with the FP unit’s operation.
6
9
1
5
4
3
21
8
(1) According to the Panel Cut size, make instllation holes on the panel.
(2) Check that FP has instllation fastners. Insert the FP from the front.
(3) The following figures show the eight(4) fastener insertion slot locations. Insert each
fastener’s hook into the slot. Tighten the screws in a diagonal pattern, and slowly
increase the torque.
• To avoid an electric shock, when connecting the FP’s power cord terminals to the
power terminal block, confirm that the FP’s power supply is completely turned OFF,
via a breaker, or similar unit.
5Instllation
• Installation gasket must be used even though it is not necessary for
its environment. For installation, refer to the FP-3500T/3600T/
3650T series User Manual.
• Tightening the screws with too much force can damage the FP unit’s
case.
• The necessary torque is 0.5N•m.
6Wiring
227.5
+1
0
FP
Unit: mm [in] 301.5 [11.87 ]
+1
0 +0.04
0
[8.96 ]
+0.04
0
under 4-R3
FP
Panel Panel thickness
1.6[0.06] to 10[0.39]
Bottom
Insertion
Slots
Panel Installation
fastener
Top
FP
Hook
9
• To avoid the dangers of fire, electric hazards and equipment damage, be sure to use
only the specified voltage when operating the FP.
• Since there is no power switch on the FP unit, be sure to attach a breaker-type switch
to its power cord.
Electrical Specification
Environmental Specification
Power Cable Connecting
Connecting the FP Power Cord
(1) Be sure that the FP’s power cord is not plugged in to the power supply.
(2) Remove the Terminal Strip’s clear plastic cover.
Item Specification
Power Supply
Input Voltage AC100 ~ 240V
Rated Voltage AC85V ~ AC265V
Rated Frequency 50 / 60HZ
Allowable Frequency Range 40Hz - 72Hz
Allowable Voltage Drop 1 cycle (Max.)
Power Consumption AC100V 0.90A or less (TYP 0.55A)
AC240V 0.45A or less (TYP 0.30A)
In-Rush Current 60A (Max.)
Voltage Endurance AC1500V 20mA for 1 minute
(between charging and FG terminals)
Insuration Resistance DC500V 10MΩ (Min.)
(between charging and FG terminals)
Item Specification
Surrounding Air
Temperature 0~50ºC (The panel should not incline more than 30º)
Storage Temperature -20 ~ +60ºC
Ambient Humidity 10~90%RH
(No condensation, Wet bulb temperature: 39ºC max.)
Storage Humidity
Air Purity (Dust) 0.1mg/m3(Max.) (No electrically conductive dust is allowed)
Pollution Degree Pollution Degree 2
AC cable Grounding Wire
Power Cord Double insulation wire
1.25~2.0 mm2
[0.0024inch2to 0.0062 inch2]
(16-14AWG)
1.25~2.0 mm2
[0.0024inch2to 0.0062 inch2]
(16-14AWG)
Recomended Ring
terminal*1
*1. In order to prevent a short circuit caused by loose screws, make sure to use a
crimp-type terminal with insulating sleeve.
V2-MS3 compatible
(J.S.T. Mfg. Co.,Ltd).
Over ø3.2 mm[0.13 in.]
V2-P4 compatible
(J.S.T. Mfg. Co.,Ltd).
Over ø4.3 mm[0.17 in.]
Under 6.0 mm
[0.24 in.] Under 7.0 mm
[0.28 in.]
10
(3) Remove the screws from the two (2) terminals (L,N) and FG (Frame Ground)
Terminal, position the Ring Terminals and reattach the screws. (Check each wire to
make sure the connections are correct)
(4) Reattach the Terminal Strip’s clear plastic cover.
USB Cable Clamp Attachment Procedure
Installation to USB cable
(1) Connect the USB cable to the connector.
(2) Tighten the clamp until the cable is secured in place and insert the convex of cable
clamp into the USB fixing hole to fix both as shown in the following figure.
USB Cable Clamp Removal Feature
(1) Push in the cable clamp's stopper with a standard flat-blade screwdriver until the
cable clamp is unlocked, and remove it.
(2) Disconnect the USB cable.
Please pay special attention to the following instructions when connecting the power cord
terminals to the FP unit.
• If the power supply voltage exceeds the FP unit’s specified range, connect a voltage
transformer.
• The torque required to tighten these screws are as follows:
Terminal Block: 0.5 to 0.6N•m.
FG (Frame Ground) Terminal: 0.6 to 0.7 N•m.
7Using the USB Cable Clamp
• If the stopper will not move, press on <A> (shown in the figure) to
free the clamp from the clamp holder.
8Power Supply Cautions
DON’T
CONNECT
FG (Frame Ground) Terminal
USB cable
USB Cable Clamp
Stopper
<A>
USB fixing hole
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
