Hwasung HP-283 Bedienungsanleitung

Technical Manual

HP-283

Title Rev. Page

HP-283 Technical Manual Ver1.0 P.1

CAUTION :

Please do not disassemble / reorganize the product.

Please do not the remove the paper jam during power on.

Please do not exceed the standard power voltage.

Please do not touch the product with your hands wet.

Please do not press / shock the product.

Please do not put the product at the moist (humid) condition.

Please do not wash off the auto cutter, / thermal print head.

Please do not touch the auto cutter, / thermal print head.

WARNING :

Please contact us if there is any problem.

Please power off the printer, once you remove the paper jam, and the foreign materials.

Please clear the air / open the disclosed place.

Please set the product without damage enviornment.

Please set the product and the cable at the stable place.

Pleaes keep the requires as necessary as general electrics.

Pleaes use the power supply set provided.

Pleaes power off the product, when the paper is changed.

Otherwise, the auto cutter / the thermal print head could be operated incorrectly.

Title Rev. Page

HP-283 Technical Manual Ver1.0 P.2

Content

1.NameofPart 3

1-1)Name 3

1-2) Connector 4

2.Howtouse 6

2-1) Paper set up 6

2-2) Paper jam 7

2-3)Selftest 8

2-4)HEXDump 8

2-5) On board update 9

2-6)DipSwitch 10

2-7) Memoryswitch 12

2-8) Recover firmware (Reboot) 14

3. Specification 17

3-1)Printer 17

3-2) Interface 18

4. Cash drawer / Melody box 23

4-1) Cash drawer 23

4-2) Melody box 24

5.Command 26

6. Windows Driver 67

6-1)Printer 67

6-2) Paper 68

6-3)Newpaper 69

7. USB (User Interface) 71

8. Ethernet 77

*Specrevision 79

Title Rev. Page

HP-283 Technical Manual Ver1.0 P.3

1.Name of Part

1-1) Name

1) LED

◈POWER LED(Blue) : It indicates the power is on

◈ERROR LED(Red) : 1. It indicates, when the printing is not available, when the paper detected

2. It indicates, when the status is error (twinkle).

Notice : It doesn’t indicate, when the status is normal.

◈PAPER LED(Orange) : 1. It indicates, when the paper is ending, and not available.

Notice : It doesn’t indicate, when the paper is set up normally.

◈FEED : : 1. It is a button to feed the paper.

2. It is a button to conduct the self-test, when you power on during you press down this button.

2) Power switch

It is a switch to power on/ powerr off.

3) Cover open

It is a lever to change the paper, and to open the cover.

Notice : When you press down the cover open lever, please do not open the cover if it is not open.

Please look at the article of paper jam this manual.

It is very important to prevent the product from the damage.

4) Cutter open (Front cover)

It is to remove the paper jam. Please look at the article of paper jam.

POWER

COVER OPEN

FEED

PAPER OUT LED

ERROR LED

POWER LED

CUTTER OPEN

(FRONT COVER)

Title Rev. Page

HP-283 Technical Manual Ver1.0 P.4

1-2) Connector

: It is to connect any device with the printer.

1) Power : It is to connect the external power 24Voltage. Please use the power supply we provide.

Notice : Please make sure about the direction of connector.

2) Cash drawer / Melody box : It is to connect the cash drawer / the melody box with the printer.

Notice : Please use the standard cash drawer.

Please read ‘4.Cash drawer / Melody box’ at this manual.

Please do not connect with the cable of Modem / Lan.

It is very important to prevent the product from the damage.

3) Interface card : It is to connect the interface cable with each hosts.

You are able to connect RS232C,PARALLEL,USB type B, Serial extension RJ-45, and Ethernet.

◈RS232C : Connector DSUB25 pin Female.

Power

Cash drawer / Melody box

Interface card

(Ex,RS232C Card) USB type B

Notice: The sign ‘arrow’ should be downward to connect with the printer.

24V

GND

N.C

Title Rev. Page

HP-283 Technical Manual Ver1.0 P.5

◈ Parallel : IEEE-1284 type B 36pincs Receptacle / Bi-directional interface card..

◈Ethernet : LAN 8 pins

◈ Serial extension RJ-45 :

It is to extend the serial RJ-45.

It is to communicate with rs232c, when you use the RS232c cable 9 pins,

or the Lan cable 6 pins one to one

DSUB- 9 pins RJ-45 6 pins receptacle

Notice : Please do not connect with the cable of Modem / Lan .

It is very important to prevent the product from the damage.

Title Rev. Page

HP-283 Technical Manual Ver1.0 P.6

2.How to use

2-1) Ppaer set up

1) Please press the button (Cover open) as the image below, and open the cover.

2) Please make sure the paper direction as the images below.

Notice : Please make sure the paper is out as image below, when you close the cover.

You can see the paper is printing and cut, when you close the cover, after you power on.

3) You can see the paper is printing and cut, when you close the cover, after you power on.

Title Rev. Page

HP-283 Technical Manual Ver1.0 P.7

2-2) Paper Jam.

Please follow the instruction as belows., when the paper jam occurred.

1) Please power off the pritner.

Notice :

Please power off the printer, once you remove the paper jam, and the foreign materials.

Pleaes power off the product, when you conduct this step.

Otherwise, the auto cutter / the thermal print head could be operated incorrectly.

The printer, and you will be damaged.

2) Please pull out the cutter cover to open as image below.

3) Please make sure the cutter is moving, when you turn the gear into one direction.

You can turn the gear into any direction, such as from the lower and the upper, from the upper and the lower.

4) Notice : Please do not turn the gear any more,

when you see the cutter is not moving any more.

Please try to change the direction which you turn the gear.

Notice : Please turn the gear, till you make sure you are able to press the cover open lever.

5) If you can press the cover open lever, please open the cover, and remove the paper jam.

Notice : Please make sure again you do not turn the gear any more,

when you see the cutter is not moving any more.

Please change the direction which you turn the gear.

Please turn the gear, till you make sure you are able to press the cover open lever.

Cutter open

gear

Title Rev. Page

HP-283 Technical Manual Ver1.0 P.8

2-3) Self test :

Without the host, or the communication, it is to print the status of printing.

Please power on, once you press down the button of feed.

It is printing the status of printing with the detail as belows.

◈Model

◈Firmware / Date

◈Interface

◈Dip switch

2-4) HEX Dump

2.4.1. Please power on after the dip switch 8 (up) of 1.

2.4.2. Then it prints all data in hex character (16 antilogarithm).

2.4.3. You can see the status of receipt.

2.4.4. It will be useful for the appilcation you do.

◈It prints the data, once it receives the data 10 digit.

◈You can print the data less than 10 digit, when you press down the button of feed.

◈It prints the control code (1F16 below) as “.”

◈It prints the data 8016 more as “^”.

[Sample]

16 antilogarithm ASCII

[HEX DUMP MODE]

41 42 43 44 45 46 47 47 49 4A ABCDEFGHIJ

30 31 32 33 34 35 36 37 38 39 0123456789

1B4AFF .J^

Title Rev. Page

HP-283 Technical Manual Ver1.0 P.9

2-5) ) On board update :

Notice : Please make you conduct the following instructions, when you get to know completely.

1) Please power off and on, after you do *up the eighth (8th) of Dip Switch 2.

Then the error LED (Red) will be lighted on, after the light goes on and off twice.

*up :on

2) Please connect the *data cable with the printer.

*data cable : interface cable (ex.serial cable, parallel cable, usb cable,etc.)

Notice : Please make sure you connect the cable of standard, or the cable provided.

3) Please conduct the update program we provide, after you set up the model / the port.

The update starts,when the error LED (Red) will be lighted on,after the light LED goes off 4 seconds.

Notice : Please do not power off, before the update is complete.

4) The update is completed, when you see the indication in the program.

5) After you complete the update, please power off and on,

after you do *down the eighth (8th) of Dip Switch 2.

*down :off

6. Then you can use the printer which is updated.

Notice : You have to stop updating, if the error LED (Red) continues flickering,

because it means error of update.

Please close the program you open.

Please check the cable if it is correct.

Please go back to the instruction of step 1), and do it again.

Andere Handbücher für HP-283

Inhaltsverzeichnis

Andere Hwasung Drucker Handbücher

Hwasung

Hwasung HMK-825 Bedienungsanleitung

Hwasung

Hwasung HPP-240 Bedienungsanleitung

Hwasung

Hwasung 054 Series Bedienungsanleitung

Hwasung

Hwasung HP-283 Bedienungsanleitung

Hwasung

Hwasung HMK-072 Bedienungsanleitung

Hwasung

Hwasung HMC-060 Bedienungsanleitung

Hwasung

Hwasung HP-500 Bedienungsanleitung

Hwasung

Hwasung HMK-056 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung