Hybrid+ HMHSPOT40 Bedienungsanleitung
USER MANUAL
40 WATT
LED SPOT
HMHSPOT40
PAGE 1
WELCOME
Congratulations on your purchase of the HMHSPOT40 Hybrid 40 Watt LED Spot, engineered
and designed by Hybrid.
Please read the instructions carefully which includes important
information about the installation, operation and maintenance.
SAFETY INTRODUCTIONS
Please keep this User Manual for future consultation. If you sell the fixture to another user,
be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the fixture.
Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid
electric shock.
Disconnect main power before servicing and maintenance.
Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only,
but always by taking its base.
Maximum ambient temperature is Ta : 40°c. Don’t operate it where the temperature is
higher than this.
In the event of serious operating problem, stop using the fixture immediately. Never try to
repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage
or malfunction. Please contact the nearest authorized technical assistance center.
Always use the same type spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain
or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the LED light beam while the fixture is on.
PAGE 2
WARNING
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain
or moisture.
Do not open the unit within five minutes after switching off.
The housing, the lenses, or the ultraviolet filter must be replaced if they are
visibly damaged.
TECHNICAL SPECIFICATIONS
11 and13 DMX channels
Pan : 540degree Tilt : 270degree
4 Operational Modes: DMX, Master/Slave, auto ,sound activated
Gobo wheel : 11 static gobos/sharking + open
Color wheel: 9 fixed colors + White
Light Source: 1x40W White LED
Power supply: 100 - 240Vac 50-60Hz
Power consumption: 65 W
Packing Size:L375×W260×H305mm
Weight: 5.65k
CAUTION
There are no user serviceable parts inside the fixture. Do not open the
housing or attempt any repairs yourself. In the unlikely situation,
your unit may require service, please contact your nearest dealer.
PAGE 3
USER MANUAL - HMHSPOT40 PROFESSIONAL LED SPOT
INSTALLATION
The unit should be mounted via its screw holes on the bracket.
Always ensure that the unit is firmly fixed to avoid vibration and slipping
while operating. Always ensure that the structure to which you are attaching
the unit is secure and is able to support a weight of 10 times of the unit’s
weight. Also always use a safety cable that can hold 12 times of the weight
of the unit when installing the fixture. The equipment must be fixed by
professionals.And it must be fixed at a place where is out of the touch of
people and has no one pass by or under it.
1. MENU
2. UP
3. DOWN
4. ENTER
To select the program function
Increase parameter
Reduce parameter
Enter sub menu
HOW TO SET THE UNIT
Display and buttons
1
7
5 6
8
2 3 4
PAGE 4
Display Value Noted
DMXAddr 001-512 DMX address select
WorkMod
DMX512 DMX Mode
AUTO Auto Mode
SOUD Sound Mode
ChNd
11Ch 11channels mode
13Ch 13 channels mode
Toot Display
ON LCD Display ON
60S LCD Display Off after 60s no operate
SundHig 0-16 Sound sensitive
MotorST
ColrREV 0-255
GoboREV 0-255
PrimREV 0-255
FousREV 0-255
PanREV 0-255
TiltREV 0-255
Xreverse
NO Pan Forward
YES Pan Reverse
Yreverse
NO Tilt Forward
YES Tilt Reverse
Xyfbstin
NO XYOptical Coupling Closed
YES XYOptical Coupling Open
Info
Version Software Version
Runtime Units:hours
Rest
NO
YES Reset
MAIN FUNCTION CHART
USER MANUAL - HMHSPOT40 PROFESSIONAL LED SPOT
PAGE 5
HOW TO CONTROL THE FIXTURE
There are two ways to control the fixture
A. Universal DMX controller
B. Master/Slave operation
A. Universal controller
The fixture can be set the DMX address remotely by universal DMX controller.
First, you need to programming two scenes into a chase, and then link the
fixtures to the universal DMX controller. When you run the chase, all the
fixtures of the chain will be set the series DMX address automatically.
The fixture uses four channels. Please refer to the following diagram to set
the address for the first four units.
B. Master/Slave operation
The fixture will allow you to link 16 fixtures together and operate without a
controller. In Master/Slave mode, the first fixture will control the others to
give an automatic, sound activated, synchronized light show. This function
is good when you want an instant show. The first fixture it’s DMX input cable
will have nothing connect it, and the other fixtures will be set in slave mode
automatically. Their DMX input cables connect the last fixture DMX output
cable (daisy chain). Any fixture can act as a Master or as a Slave
OR
001 012 023 034
001 014 027 040
PAGE 6
11CH 13CH Value Function
1 1 0-255 Pan
2 0-255 Pan fine
2 3 0-255 Tilt
4 0-255 Tilt fine
3 5 0-255 Pan/Tilt speed from fast to slow
4 6 0-4 No function
5-255 Mater Dimmer
5 7
0-3 No Strobe
4-59 Strobe effect from slow to fast
60-63 No Strobe
64-123 Random Strobe effect from slow to fast
124-127 No Strobe
128-191 Pulse Strobe effect from slow to fast
192-195 No Strobe
196-253 Random Pulse Strobe effect from slow to fast
254-255 No Strobe
6 8
0 -127 Continual positioning
128 -130 Colour half
131 -133 Color 1
134 -136 Colour half
137 -139 Color 2
140 -142 Colour half
143 -145 Colour 3
146 -148 Colour half
149 -151 Colour 4
152 -154 Colour half
155 -157 Color 5
CONFIGURATION
USER MANUAL - HMHSPOT40 PROFESSIONAL LED SPOT
PAGE 7
158 -160 Colour half
161 -163 Color 6
164 -166 Colour half
167 -169 Color 7
170 -172 Colour half
173 -175 Color 8
176 -178 Colour half
179 -181 Color 9
182 -184 Colour half
185 -187 Color 10
188 -194 Open
195 - 219 Forwards rainbow effect from fast to slow
220 -224 No rotation (White)
225 -249 Backwards rainbow effect from slow to fast
250 -255 Colour marcos
7 9
0 - 4 Open
5 - 9 Gobo 1
10 -14 Gobo 2
15 -19 Gobo 3
20 - 24 Gobo 4
25- 29 Gobo 5
30 -34 Gobo 6
35 -39 Gobo 7
40-44 Gobo 8
45-49 Gobo 9
50-54 Gobo 10
55-59 Gobo 11
60-64 Open
65-74 Gobo 1 Shake
PAGE 8
75-84 Gobo 2 Shake
85-94 Gobo 3 Shake
95-104 Gobo 4 Shake
105-114 Gobo 5 Shake
115 -124 Gobo 6 Shake
125 -134 Gobo 7 Shake
135 -144 Gobo 8 Shake
145 -154 Gobo 9 Shake
155 -164 Gobo 10 Shake
165 -174 Gobo 11 Shake
175 -179 No rotation (open)
180 -204 Forwards gobo wheel rotation from fast to slow
205 -214 No rotation (Stop)
215 -239 Backwards gobo wheel rotation from slow to fast
240 -255 Gobo Marcos
8 10
0 -15 Open
16 -127 Prism indexing
128 -255 Prism 2
9 11 0 -255 Focus Continuous adjustment from far to near
“10
Macro
function”
12 0 -19 Custom Control by CH1-CH9
20 -99 Auto (all of other CH invalid)
100-199 Sound (all of other CH invalid)
200-255 Custom Control by CH1-CH9
11 13 0 -199 Custom Control by CH1-CH9
200-255 Reset
CONNECTIONS
The HMHspot40 is widely used in intelligent lighting control, with a
maximum of 512 channels.
Inhaltsverzeichnis
Beliebte Scheinwerfer Handbücher anderer Marken
Guangzhou Yinhe Lighting&Sound Equipment Factory
Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Bedienungsanleitung
LIVARNO home
LIVARNO home 375304 2101 Originalbetriebsanleitung
Cameo
Cameo CLQS40WW Bedienungsanleitung
Leviton
Leviton Ellipsoid 5/50 Bedienungsanleitung
Monacor
Monacor img Stage Line PARL-56PDX/CR Bedienungsanleitung
Vector
Vector SL3AKV Bedienungsanleitung
EuroLite
EuroLite Akku flat light 1 Bedienungsanleitung
Commercial Electric
Commercial Electric SPTM-1401 Bedienungsanleitung
Vision & Control
Vision & Control SLB-500-W5K7-P-SL Bedienungsanleitung
Teknik
Teknik FLEXI Bedienungsanleitung
Craftsman
Craftsman CMXLSB10 Bedienungsanleitung
EuroLite
EuroLite LED SLS-144 UV Floor Spot Bedienungsanleitung