Hybsys GSM 102 Gate Bedienungsanleitung

User’s Manual

GSM 102 Gate

GSM Wireless Terminal

Appearance ___________________________________________ Error! Bookmark not defined.

LED indicators____________________________________________________________________2

Connectors _______________________________________________________________________2

Install The Terminal___________________________________________________________ 2

Installing the SIM Card ___________________________________________________________________2

The installation for connecting to ordinary telephone direct _______________________________________ 3

The installation for connecting to register cost equipment_________________________________________3

Operating the terminal _________________________________________________________ 3

The Information of Signal Quality and Software Version _________________________________________3

Inquire Signal Quality and Software Version___________________________________________________4

Signal Quality___________________________________________________________________________4

Making Calls ___________________________________________________________________________4

Answering Incoming Calls_________________________________________________________________4

Adjusting the Volume of Voice _____________________________________________________________ 4

Technical Specification ___________________________________________________________________4

The Instructions for Terminal’s Running Status_________________________________________________5

Familiar Trouble and Troubleshooting____________________________________________ 5

Hybrid Systems JSC Users Manual

Page 2 of 6 GSM 102 Gate

LED indicators (From left to right)

LED1 -Network indicator (Flashing once in one second indicates that the terminal is

on GSM network. Being dead or being lit for a long time indicates that the terminal has

failed to login onto GSM network)

LED2 -Power indicator (it’s lit while power source is connected correctly) LED3 -

Warning indicator (Staying lit more than 10 seconds indicates that the terminal can’t work

in gear. Staying lit less than 10 seconds or flashing indicate that the terminal is dealing

with short message)

LED4 -Working indicator (staying lit when handset has being lift or hand-free key

had been pressed)

LED5 -Signal indicator (The flashing speed indicates signal strength. The details

refer to “Inquire Signal

Connectors

Map 2 the rear connection map to mains

1. Phone port: Connecting to telephone (Two telephone can be connected at the same

time). Line port – connecting to the PSTN

2 Power port: Make the flat side of power adapter plug be upturned and push it in

3 Antenna port

Install The Terminal

Installing the SIM Card

Proceed as follows:

1. Slide back the SIM door and lift it up

2. Slide the SIM card into the SIM door making sure that the clipped corner of the SIM

card lines up with the clipped corner of the SIM holder

3. Close the SIM door

4. Slide the SIM door to lock the SIM card in place

Hybrid Systems JSC Users Manual

Page 3 of 6 GSM 102 Gate

Installation Condition

Require 220v AC power. GSM signal can cover the area where the terminal is placed.

Signal quality affects voice quality direct.

The installation for connecting to ordinary telephone direct

1. Install the SIM card proceeding as “Installing the SIM Card”

2. Connect one end of the telephone line to “Telephone port” and the other end connect

to a telephone.

3. Install the antenna and power supply well. The distance between telephone and

terminal is 1.5m at least.

4. Connect one end of the power adapter to “Power port” and another end connect to

220v AC power. About 10-45 seconds later, the terminal works in gear (The login

time is different according to local network).

Draw your attentions: Because there are many types of ordinary telephone and their

electric parameters are different.In order to avoid mutual disturbance between telephone

and terminal and affects voice quality.The distance between telephone and terminal must be

beyond 2m.

The installation for connecting to register cost equipment

If users demand register cost during calls, register cost equipment can be connected

between terminal and ordinary telephone. Register cost equipment registers cost according

to anti-polarity signal that is provided by terminal

Operating the terminal

The Information of Signal Quality and Software Version

If the connected telephone has the function of displaying incoming calls, the

telephone rings after it is in login onto GSM network successfully and a code of 8 digits will

be displayed. The code indicates the information of signal quality, malfunctions and software

version as follows:

- The first two digits indicate the signal quality, it ranges from “00” to “31”. Stronger the

signal is, bigger the digits is. If it is less than 10, the quality of voice will be poor.

- The third and the forth digit is the code of malfunction:“00”: good “11”: failed in login

onto GSM network “22” or “33”: PIN error (PIN code isn’t 1234 or PIN code isn’t disabled)

“44”: lock card error “55”: lock terminal error,“77”: lock network error, “99”: read SIM

card error)

- The later four digits is software version code: for example 4060 indicates the software

version code is 4.06.

If the telephone displays “11”, “22”, “33”, “44”, “77”, “99” and it can’t work in gear,

please contact the service provider.

Hybrid Systems JSC Users Manual

Page 4 of 6 GSM 102 Gate

Inquire Signal Quality and Software Version

1. Lift the handset and then dial “***9#”. Hang up as soon as you hear busy tone. The

telephone rings and displays a code of 8 digits. The code indicates the information of

signal quality and software version as follows:

The first two digits indicate signal quality. It ranges from “00” to “31”. Stronger the

signal is, bigger the digits is. If it is less than 10, the quality of voice will be poor.

The third and the forth digit is standby.

The later four digits are software version code: for example 4060 indicates the software

version code is 4.06.

Signal Quality

User can judge the signal quality according to the flashing speech of network

indicator (LED1). Flash once in four seconds: signal is good Flash once in two seconds:

signal is weakerFlash once in one second: signal is very weak, the quality of the voice is

poor, please check the terminal.

Making Calls

Lift the handset or press “hand-free” key, you will hear dialing tone, then you can

dial the telephone numbers you want to call.

Dialing: dial the telephone numbers you want to call

On completion of dialed digits, you can press “#” to transmit telephone numbers. If

you don't dial any key for continual 6 seconds during the dialing, the terminal transmits the

dialed telephone numbers automatically.

When it is necessary to register cost, the terminal sends out anti-polarity signal (the

signal is used to register cost by register cost equipment). During a call, dial digital key or

“*” or “#” to output DTMF.

If the calling party or called party hang up, the terminal stops sending out anti-

polarity signal.

If users dial barred numbers, telephone will give out the sound of three-time toot to

ask the user to hang up.

Answering Incoming Calls

When some calls are coming in, if the connected telephone has the function of

displaying incoming calls, the telephone rings and displays the incoming telephone

numbers. Now users can lift the handset or press “hand-free” to answer the call.

Adjusting the Volume of Voice

Lift the handset. Dial “*33XY#”, and then hang up when hear the sound of toot. X

and Y both belong to the digits that range from 1 to 5. X indicates microphone volume. Y

indicates speaker volume. Level 1 is the lowest volume and level 5 is the highest.

Technical Specification

•Working condition Environment temperature: 0~+50

•Relative humidity: 10%~95%

•Air pressure: 86~106kpa

Hybrid Systems JSC Users Manual

Page 5 of 6 GSM 102 Gate

•Environment yawp: ≤60dB (A)

•Working frequency: GSM900MHz/GSM1800MHz

•Stability of frequency: better than 2.5PPM

•Signal sensitivity: -103dBM

•Transmit power: <2w

•Power: 220v±15% AC

•The max distance between terminal and telephone: 100M

The Instructions for Terminal’s Running Status

The instruction for initializing terminal When LED2 is lit, the terminal begins to

initialize. If LED1 and LED4 are flashing simultaneously, the terminal is searching for GSM

network. About 1545 seconds later, the telephone rings which indicates that the process of

initializing terminal finishes. If LED3 stays lit, initialization is unsuccessful. On this condition

user can set parameters for the terminal but the terminal can’t be used to make any calls. If

users dial telephone numbers, LED3 will flash and the telephone will give out the sound of

three-time “toot” to ask the user to hang up.

While users dialed barred numbers or other error numbers, the telephone gives out

the sound of three-time “toot” to indicate that user should hang up and redial.

While you are lifting the handset and don’t dial any key for continuous 15 seconds or

the nobody answer the dialed telephone for 90 seconds after the called telephone has

ringed, the telephone will give out the sound of three-time “toot” to indicate the user to

hang up. If the user doesn’t hang up for a long time, all indicating sound will be ended after

1 minute.

While calls coming in, work indicator flashes. If user answers the call, the work

indicator stays lit.

When the handset is lift, working indicator (LED5) stays flashing until user hangs up.

When SMS is coming, warning indicator (LED3) and working indicator (LED5) both

stay lit that indicates that the terminal are dealing with SMS.

If LED3 stays flashing and the telephone gives out the sound of three-time “toot”, it

indicates that the terminal is on the warning status. Please hang up.

Familiar Trouble and Troubleshooting

Phenomena Trouble Trouble Shooting

Warning

indicator stay

lit for a long

time

Failed in login

onto GSM

network

1. The signal is too weak Please move the

terminal to the place where signal is stronger.

2. Check whether antenna is connected well.

3. SIM card is locked. Please contact the

service provider.

Signal indicator

flashes fast

Signal is too

weak

1. Check whether antenna is connected well.

2. The signal is too weak Move the terminal or

antenna to the place where signal is strong.

Power indicator

isn’t lit

Having not

connect to

power supply or

there is some

trouble with

power adapter

1. Check whether the adapter is connected

well. 2. There is some trouble with the power

adapter Please contact the provider of the

terminal.

Hybrid Systems JSC Users Manual

Page 6 of 6 GSM 102 Gate

Only free

numbers can

be called out

The residual

money on SIM

card is too less Add money to the SIM card subscriber

Can’t hear

sound during

calls

The malfunction

on the

telephone

Change the connected telephone with a good

one

Poor voice

quality during

calls or there is

echo during

calls

The voice

volume is too

high or the

signal of

network is too

weak.

1. Adjust voice volume to be lower. 2. The

local signal is too weak. Move the terminal to

the place where signal is stronger. 3. Make

the antenna is longer from the telephone 4.

The voice quality of the connected telephone

isn’t good. Change the connected telephone

5. Trouble on the GSM network.

No ringing

sound

The malfunction

on the

telephone

1. Malfunction on the connected telephone 2.

Malfunction on terminal. Please contact the

provider of the terminal.

Incoming calls

can’t be

answered

The connected

telephone does

not match the

terminal or

forbidding

answering

incoming calls is

set

1. Change the connected telephone with a

suitable one. 2. Forbidding answer incoming

calls is set up, please contact the service

provider.

FUTURE CONTACTS

Hybrid Systems JSC

BULGARIA, 1303 Sofia

70 Hristo Botev Blvd, fl. 2

Phone: (+359 2) 931 2222; 489 3200

Fax: (+359 2) 931 2384

E-mail: [email protected]

WEB: http://www.hybsys.bg

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere hybsys Modem Handbücher

hybsys

hybsys GSM 108 Gate Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

hybsys GSM 102 Gate Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken