Hyco Accona Technisches Datenblatt

Product Instruction Manual

Accona

AC500T, AC1000T, AC1500T, AC2000T

Panel heater

Version 3.2 Jan 2015

V18.4,1

Thank you for purchasing a Hyco Accona panel heater. Please ensure you

read and understand these instructions to ensure safe installation and

operation.

The Accona is ideal for a wide range of fixed installation heating applications in the home and

office environment. The Accona is ecodesign compliant; energy saving features include open

window detection and a 24/ 7 electronic timer.

ey Features

•

Slimline, modern, curved design

•

24/ 7 electronic timer

•

Reduced energy wastage with open window detection

•

Frost protection feature

•

Full or half power setting

•

IP24 splashproof

1. Important safety points

The electrical installation must be carried out by a qualified electrician in

accordance with the current edition of the I.E.E. Wiring Regulations.

Only connect the unit to a single-phase supply with a mains voltage as specified

on the rating plate.

If the heater is located in a bathroom, it must be installed so that switches and

other controls cannot be touched by a person in the bath or shower.

Only use the mounting bracket supplied and do not modify the bracket in

any way.

WARNING: To avoid overheating, do not cover the heater.

The supply cord cannot be replaced by the user. If the cord is damaged the

appliance should be returned to the manufacturer or an authorised service

agent for replacement.

The heater must not be located immediately below or above an electrical socket

outlet.

This appliance can be used by children aged from 8 years and above and persons

with reduced physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning use

of the appliance in a safe way and understand the hazards involved.

Children of less than 3 years should be kept away unless continuously

supervised.

Children aged from 3 years and less than 8 years shall only switch on/off the

appliance provided it has been placed or installed in its intended normal

operating position and they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the hazards

involved. Children aged from 3 years and less than 8 years shall not plug

in, regulate and clean the appliance or perform user maintenance.

CAUTION: Some parts of this product can become very hot and cause burns.

Particular attention must be given where children and vulnerable people

are present.

2. Installation

Wall Mounting

• Select a suitable location for the install and ensure the minimum spaces around the

heater are maintained to ensure good airflow and safe operation of the heater.

MIN 300mm

MIN 150mm

AC500T

MODEL

2000/1000830 400 300 254

1500/750 595 400 250 254

1000/500 460 400 155 254

500/250 460 400 155 254

Specification

AC1000T

AC2000T

AC1500T

• Remove the bracket from the reverse of the heater by pinching the two tabs at the

top to release it from the unit, and then unhooking the lower two tabs by tilting

the bracket away from the heater.

• Ensuring a horizontal level, offer the bracket to the wall and mark the four holes

located at each corner of the bracket.

• Drill the four holes in the mounting surface and insert the wall plugs supplied.

• Offer the bracket up to the holes before inserting the four screws supplied. Ensure

the screws are fully tightened and that the bracket holds firm to the wall.

• Offer the heater to the bracket and locate the lower bracket lugs into the

corresponding slots in the back of the heater by tilting the heater forward.

• Once the lower lugs are located, tilt the heater back towards the bracket and align the

upper bracket lugs into the corresponding slots at the top of the heater.

• Insert the screws into the upper lug holes and screw down until the heater is locked

into place.

Electrical installation

The electrical installation must be carried out by a qualified electrician in

accordance with the current edition of the I.E.E. Wiring Regulations.

• Connection should be made to the fixed wiring of the property via a double pole

fused spur with a break capacity of no less than 13amps.

• Electrical connections should be made as follows:

Green/Yellow earth wire to the terminal marked “ E” or

Brown/Red live wire to the terminal marked “L”

Blue/Black neutral wire to the terminal marked “N”

Recommended mounting height

(bottom edge of dryer above nished oor)

M43”

L41”

C39”

C33”

3. Operation

Control panel overv ew

1. Standby on/off 7. Manual mode active 13. Time display

2. Full/half power select 8. Automatic mode active 14. Target temperature

3. Element on indicator 9. Timer active 15. SET select

4. Low power active 10. UP select 16. O select

5. High power active 11. DOWN select

6. Open window active 12. Manual/Auto select

Once the heater has been switched on using the rocker switch on the right-hand side the

blue power LED indicator will be illuminated. You will then need to press the standby

on/off button under the LED indicator to activate the panel.

Sett ng the clock

• Hold down the SET & O buttons simultaneously until a beep sounds and the current

day setting flashes.

• Use the UP/DOWN buttons to cycle to the correct day and press the SET button

to store.

• The hour segment of the time display will flash with the current setting, use the

UP/DOWN button to cycle to the current hour and press the SET button to store.

• The minute segment of the time display will flash with the current setting, use the

UP/DOWN button to cycle to the current minute and press the SET button to store.

M/A

POWER

MON TUE WED THU FRI SAT SUN

LO HI WO M A

Set OK

The unit has a built-in battery that can retain the time for several days if the power is

switched off to the unit. If the unit is off for longer periods the day & time may need to

be reset upon next start up.

Sett ng the target temperature

• To set the target temperature of the heater use the UP/DOWN buttons to cycle to the

desired value and press the O button to confirm.

Sw tch ng between Full/Half power

• Press the full/half power select button to toggle between the settings. The current

setting will be displayed by either the “LO” or “HI” icon on the display.

Sw tch ng between Manual/Auto operat on

• Press the manual/auto select button to toggle between the settings. The current

setting will be displayed by either the “M” or “A” icon on the display.

Sett ng the ch ld lock

• Press the UP & DOWN buttons simultaneously and hold until a beep sounds.

The target temperature display will be replaced by “[ ]” icon to indicate the

panel is locked.

• Repeat the first step to unlock the heater.

Manual operat on

The most basic setting of the heater allows the user to control when the heater is active

by simply switching between on/off via the standby button. However, it is strongly

recommended to consider setting a timed operation by using the ‘automatic operation

mode’ where anticipated usage is predictable, to avoid energy wastage.

• Select the manual operation mode by pressing the manual/auto (M/A) select button.

To confirm the selection check that the “M” icon is displayed.

• The heater will maintain the temperature displayed unless switched off or placed

into standby mode.

Manual operat on (auto power off mode)

Whilst the heater is running in manual mode it is possible to control the length of time

the heater will operate for using a basic timer function. Using this you can select the

desired time for the heater to switch off. This feature helps to ensure the heater is not

turned on and forgotten about.

• Select the manual operation mode by pressing the manual/auto (M/A) select button.

To confirm the selection check that the “M” icon is displayed.

• Press the SET select button to enter the power off time programming screen.

• The hour setting will flash on the display. Use the UP/DOWN select buttons to

change the desired hour for the heater to turn off and press the SET select button.

• The minute setting will now flash on the display and can be altered using the

UP/DOWN select buttons as per the previous step.

• Once the desired hour & minute are displayed, press the O select button to confirm

the power off time setting.

• The heater will now display the “timer active” icon to confirm the feature is active.

• The power off time setting will be cleared if the heater is switched off or placed into

standby mode.

Automat c operat on (24/7 t mer)

Example below shows a timer programmed for TUESDAY to switch ON at 8.00am (08)

and OFF at 5.00pm (17). This is schedule number 1. See key for further information.

1 Switch on hour

2 Switch off hour

3 Schedule number (1-4)

The automatic operation mode allows the heater to be operated by a user defined

schedule. This offers up to four separate periods of operation to be defined for each day.

This feature is strongly recommended where heat demand is predictable as it can help

reduce energy wastage. In addition, this allows spaces to be heated in anticipation of

the demand without the need for somebody to be present to turn it on; for example,

in an office environment where staff arrive to begin work at 8.30am, turning the heater

on at 8am to pre-warm the room.

M/A

POWER

MON TUETTUTUE WED THU FRI SAT SUN

LO HI

TUE

HI WO M A

TUE

HI A

Set OK

• Select the automatic operation mode by pressing the manual/auto (M/A) select

button. To confirm the selection check that the “A” icon is displayed.

• Press the SET select button to enter the 24/7 timer programming screen.

• The day setting will flash on the display. Use the UP/ DOWN select buttons to move

between the available days and press the SET select button to confirm when the

desired day to be programmed is flashing.

• The time display will now show a flashing hour setting, this is the hour at which the

heater will automatically switch on (note t s only poss ble to set the t mer to full

hours, m nutes cannot be set). Use the UP/DOWN select buttons to choose the

desired hour to switch on and press the SET select button to confirm.

• The second option to be set on the time display will now flash, this is the hour at

which heater will automatically switch off. Use the UP/DOWN select buttons to

choose the desired hour to switch off and press the SET select button to confirm.

• The time display will now move to the next schedule you can create (shown by area

‘3’ on the annotated image) and the previous steps for setting the switch on and off

hours should be followed.

• Up to 4 individual start stop times can be specified for each day but it is possible to

exit and store the schedules once the desired number of operations have been set,

simply press the O select button at any time to store and exit the scheduling feature.

• Repeat all steps for each day of the week where timed operation is required. The

default for each day and period of operation is off so it is not necessary to enter any

days that are not required.

When the heater is in a defined period of non-operation it will automatically go into

standby mode. It can be woken up in order to alter any settings by pressing the standby

on/off button but will go back into standby if no settings are changed within 10 seconds.

If you want to switch the heater on outside of the usual, programmed user set schedules

you will need to override the automatic operation mode. This can be done by pressing

the standby on/off button under the LED indicator to turn the heater on. You will then

need to select the manual operation mode by pressing the manual/auto (M/A) select

button. To confirm the selection check that the “M” icon is displayed. This is the most

basic method of operation and will mean the heater remains switched on, until it is

turned off. Please note, to return to programmed user set schedules you will need to

select the automatic operation mode by pressing the manual/auto (M/A) select button

prior to switching off. To confirm the selection check that the “A” icon is displayed.

Frost protect on

The heater has a built-in frost protection mode which will not allow the temperature of

its surroundings to drop below 50 C. This feature will operate regardless of any settings

that have been selected on the heater. The only way to prevent this feature operating is

to switch off the heater at the main switch (not standby).

4. Maintenance

The heater should be inspected and cleaned periodically, attention should be given

to the inlet grilles at the base of the unit and the outlet louvres at the front of the

heater. Ensure they are cleared of dust or other debris that may causes a blockage

and in turn reduce the airflow in and out of the heater, which if unchecked may lead

to the unit running at hotter temperatures.

• Ensure the heater is isolated from the power supply and has fully cooled down

before commencing any cleaning of the heater.

• Use a soft brush or vacuum cleaner to gently remove any debris from the inlet grilles

and outlet louvres.

• Use a non-abrasive, damp cloth with soapy water to clean the main body of the

heater. Take care not to use excessive amounts of water that could run into main

body of the heater.

Sooty deposits can adhere to the louvres of the heater and the surrounding surfaces

of the heater install. This can be caused by excess dust in and around the heater burning

off the heating element after prolonged periods of non-use. This does not indicate an

over-heat occurrence and the effects can be reduced with regular cleaning of the

heater.

Andere Handbücher für Accona

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hyco Heizung Handbücher

Hyco

Hyco Accona Technisches Datenblatt

Hyco

Hyco sun king sk1000 Bedienungsanleitung

Hyco

Hyco Scirocco SC2000Y Technisches Datenblatt

Hyco

Hyco Accona AN500T Technisches Datenblatt

Hyco

Hyco SK1500 Bedienungsanleitung

Hyco

Hyco Zephyr DF20 Bedienungsanleitung

Hyco

Hyco MS180 Bedienungsanleitung

Hyco

Hyco RAD15Y Bedienungsanleitung

Hyco

Hyco AC2400T Technisches Datenblatt

Hyco

Hyco AN1000 Technisches Datenblatt

Hyco

Hyco Vicenza VC1200T Technisches Datenblatt

Hyco

Hyco AVG600T Technisches Datenblatt

Hyco

Hyco Sun Prince Bedienungsanleitung

Hyco

Hyco Sun Prince SP1000H Bedienungsanleitung

Hyco

Hyco Sahara TH01B Bedienungsanleitung

Hyco

Hyco Sahara TH01B Technisches Datenblatt

Hyco

Hyco scirocco SC2000Y Bedienungsanleitung

Hyco

Hyco DF20LL Bedienungsanleitung

Hyco

Hyco Accona AN2000T Bedienungsanleitung

Hyco

Hyco FH-201 Bedienungsanleitung

Hyco

Hyco Fiji FH-201Z Bedienungsanleitung

Hyco

Hyco MG1000T Bedienungsanleitung

Hyco

Hyco Sun King Quartz Bedienungsanleitung

Hyco

Hyco Ariano AR1000T Technisches Datenblatt

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung