HYDAC FILTER SYSTEMS LOGO! TDE Bedienungsanleitung

LOGO

REPLACEMENT

MODULE TDE

for FAM-5

Installation Manual

English (translation of original instructions)

Keep for future reference.

Documentation no.: 4359963

Content

FAM 5 en-US Page 2 / 12

MOWA LogoTDE 4359963 en 2018-05-23.docx

2018-05-08

Content

Content ..........................................................................................................2

Preceding note..............................................................................................2

Replacing the Logo! of the TDE module.....................................................3

Preparing the Logo! of the TDE module......................................................4

Preparing the Logo! of the TDE module for assembly.................................6

Installing the Logo! of the TDE module........................................................7

Determining the configuration of the FAM ...............................................10

Model code................................................................................................10

IndexKeine Indexeinträge gefunden.............................................................11

Preceding note

This instruction manual is meant to be a supplement to the Operating- and

Maintenance instructions for the FAM. Therefore, it is limited to the

replacement of a defective Logo! of the TDE module. Everything else, such

as the explanation of symbols and formal explanations can be taken from the

Operating and Maintenance instructions for the FAM.

The Logo! of the TDE replacement module is supplied as a spare part,

without being configured. After being installed, it must be adapted to the

model version of your FAM. In order to do this, use the Operating and

Maintenance Instructions for the FAM.

Use the Operating and Maintenance instructions for the

FAM.

Replacing the Logo! of the TDE module

FAM 5 en-US Page 3 / 12

MOWA LogoTDE 4359963 en 2018-05-23.docx

2018-05-08

Replacing the Logo! of the TDE module

In this chapter, you will find the required specifications to replace the

defective Logo! of the TDE module with a new module. The listed illustrations

show the module at the front of the switch cabinet. It is at the head in the

case of the FAM. The replacement process described does not change due

to this with regard to how it is carried out.

DANGER

Electric shock

Danger of fatal injury

►Any work involving the electrical equipment

may only be done by a properly trained,

certified electrician.

The jobs listed below may only be carried out by properly trained, certified

electricians, who meet the following conditions:

Only specialist personnel with training as electricians and

the following knowledge:

•Safe handling/use of tools

•Fitting and connection of electrical lines, electrical

machinery, sockets, etc.

•Checking the phase sequence

•Product-specific knowledge

•Knowledge about how to handle operating media.

Screwdriver

Replacing the Logo! of the TDE module

FAM 5 en-US Page 4 / 12

MOWA LogoTDE 4359963 en 2018-05-23.docx

2018-05-08

NOTICE

Unit in a condensation state

Risk of a short circuit

►Do not switch on the Logo! of the TDE module when it is in a

condensation state.

►Allow it to come to room temperature before commissioning it.

►While doing so, do not expose the Logo! of the TDE module to any

direct heat radiation from heating devices.

If the unit is exposed to, or has been exposed to, climatic fluctuations

(temperature fluctuations, humidity), moisture can condense on or inside the

unit (unit in a condensation state).

If there is condensation in or on the unit or if the unit has been exposed to

temperature fluctuations, allow it to come to to room temperature before

starting it up.

Preparing the Logo! of the TDE module

In order to disassemble the Logo! of the TDE module, proceed as follows:

Switch off the E-Box via the main

switch.

Replacing the Logo! of the TDE module

FAM 5 en-US Page 5 / 12

MOWA LogoTDE 4359963 en 2018-05-23.docx

2018-05-08

Pull the E-Box's power plug.

Open the door to the E-Box with

the suitable key.

Disconnect all cables and

connection plugs on the rear side

of the Logo! of the TDE module.

Unscrew the set screws out of

the holding brackets

counterclockwise.

Remove the four holding

brackets and push the Logo! of

the TDE module from the back to

the front out of the cut-out

section in the door.

The disassembly of the Logo! of

the TDE module is complete.

Replacing the Logo! of the TDE module

FAM 5 en-US Page 6 / 12

MOWA LogoTDE 4359963 en 2018-05-23.docx

2018-05-08

Preparing the Logo! of the TDE module for assembly

Check the module for transport damage. The module may only be installed

and operated in perfect technical condition, in compliance with this

document.

If no sealing cord has been glued in place in groove (A) on the rear side of

the module's front panel, insert the sealing cord provided in groove (A) and

cut the sealing cord to length so that the joint closes with a tight seal.

NOTICE

Leaks at the Logo! of the TDE module

Moisture/water enters into the E-Box via the Logo! of the TDE module

►Ensure that the sealing cord is inserted cleanly. If the inserted sealing

cord is twisted or if the joint is not adequately closed, leakage can

occur.

►Cut the sealing cord to length and insert it such that the joint closes

with a tight seal.

Replacing the Logo! of the TDE module

FAM 5 en-US Page 7 / 12

MOWA LogoTDE 4359963 en 2018-05-23.docx

2018-05-08

Installing the Logo! of the TDE module

In order to install the Logo! of the TDE module, proceed as follows:

Prepare the Logo! of the TDE

module for installation according

to Chapter "Preparing the Logo!

of the TDE module for

assembly", page 6.

Insert the Logo! of the TDE

module from the front through

the cut-out section in the door.

Ensure that it is installed

with the correct orientation

(top/bottom).

All ports/sockets are located at

the bottom.

Pre-mount the set screws

provided in the holding brackets.

The tips of the set screws must

point toward the wide ends of

the holding brackets.

Hook the holding brackets into

the corresponding recesses in

the unit as follows and fix the

unit in place by tightening the

set screws until the front of the

Logo! of the TDE module is flush

with the surface of the switch

cabinet at the fastening points.

Note the maximum

torque of 0.1 Nm.

Replacing the Logo! of the TDE module

FAM 5 en-US Page 8 / 12

MOWA LogoTDE 4359963 en 2018-05-23.docx

2018-05-08

Only the Logo! of the

TDE module with the four

mounted holding brackets fulfil

protection class IP65.

Insert all cables and connection

plugs into the corresponding

ports on the rear side of the

Logo! of the TDE module.

Close the door to the E-Box with

the suitable key.

Plug in the power connector and

switch the touch panel on at the

main switch.

Check the display of the Logo!

Replacing the Logo! of the TDE module

FAM 5 en-US Page 9 / 12

MOWA LogoTDE 4359963 en 2018-05-23.docx

2018-05-08

of the TDE module at starting.

The user interface starts

automatically.

The assembly of the Logo! of

the TDE module is complete.

Determining the configuration of the FAM

FAM 5 en-US Page 10 / 12

MOWA LogoTDE 4359963 en 2018-05-23.docx

2018-05-08

Determining the configuration of the FAM

In order to adapt the Logo! of the TDE replacement module to your FAM, you

require the model version given in the model code. In order to decode this,

use the following table.

Adapt the configuration of the replacement module according to the model

version. The guidelines for this are the chapters "Configuration menu,

Changing the configuration, Exiting the configuration menu" in the Operating

and Maintenance Instructions for the FAM.

Model code

FAM

Product

FAM = FluidAqua Mobil

Filter Size

…

Operating fluid

…

Mechanical type

…

Voltage/frequency/power supply

…

Filter size fluid filter

…

Vacuum pump

…

Heater

Z = No heater

H = Heater (for 200 … 359 V = 1 kW, for

360 … 690 V = 2.4 kW)

Control concept

…

Instrumentation

Z = Without

AquaSensor (AS)

AC = AquaSensor (AS)+ContaminationSensor

(CS)

ACS = AquaSensor (AS) + ContaminationSensor (CS)+

SensorMonitoring Unit (for displaying and saving the

measured values)

Modification number

…

Supplementary details

…

Inhaltsverzeichnis

Andere HYDAC FILTER SYSTEMS Steuereinheit Handbücher

HYDAC FILTER SYSTEMS

HYDAC FILTER SYSTEMS CTM-EB 1000 Series Handbuch

HYDAC FILTER SYSTEMS

HYDAC FILTER SYSTEMS CTM-EF Handbuch

HYDAC FILTER SYSTEMS

HYDAC FILTER SYSTEMS FMM-P-S Bedienungsanleitung

HYDAC FILTER SYSTEMS

HYDAC FILTER SYSTEMS CSM 1000 Series Bedienungsanleitung

HYDAC FILTER SYSTEMS

HYDAC FILTER SYSTEMS FluidControl FCU 8111 Handbuch

HYDAC FILTER SYSTEMS

HYDAC FILTER SYSTEMS CTM-EF 3 3 Series Handbuch

HYDAC FILTER SYSTEMS

HYDAC FILTER SYSTEMS FMM-A-S Series Bedienungsanleitung

HYDAC FILTER SYSTEMS

HYDAC FILTER SYSTEMS FCU 2000-4 Series Handbuch

HYDAC FILTER SYSTEMS

HYDAC FILTER SYSTEMS FCU 1210 Handbuch

HYDAC FILTER SYSTEMS

HYDAC FILTER SYSTEMS FMM-A-S Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung