HydroCare Quadmaxx Gebrauchsanweisung

Installation,

Use and Care Manual

Parts Included

Backing w/ Inlet and Outlet Pipe Manifolds

4 Sleeves w/ Purification Media

Media Removal Tool/ManifoldAdjuster

Wall Mount Screws w/ Anchors

Disconnect Clip

1 set of Sleeve Bypass Caps

Cap of Silicone Grease

Tools & Parts Needed

■

Level

■

#2 Phillips Screwdriver

■

Adapters from home pipe size and type to 1” Copper

■

If incoming water pressure is over 80 PSI, install a pressureregulator.

Installation Requirements

Install upside down or sideways. All of the arrows on the Sleeves must point in the same

direction from inlet to outlet which is the direction of the water flow.

The system should be located after connection for the outside hose bibs, sprinkler system(s),

and/or irrigation line(s). These lines should be left untreated. Do not use with water that is

microbiologically unsafe or of unknown quality without adequate disinfection before or after

the system.

Install in a location that is not susceptible to freezing temperatures as damage to the Sleeves

could occur. Install away from direct sunlight as prolonged exposure to light can weaken plastic

components.

The system needs to be mounted to a solid surface (Backing is drilled for 16 inches on center).

Wall anchors are provided if needed.

You may consider an optional Bypass Assembly with additional shutoff valves for convenience

when changing your HydroCare Patented PurificationMedia.

E F

Temporarily remove the Media Removal Tool from the Quadmaxx® Backing.

Use a level and pencil to locate your 4 wall mount locations. If using wall anchors, press the tip of the

anchors into drywall using a #2 Phillips Screwdriver. Drive anchor clockwise until anchor stops flush

with wall. Do not over tighten anchors. Place Backing over marked locations or inserted anchors and

insert wall mount screws. Tighten screws flush with the Backing. If using anchors, a “pop” sound

indicates correct installation.

Your system may require the insertion of the media. Open the tube and check. Follow the instructions

and then continue with attaching the filter tubes.

Unpack the new HydroCare Purification Media. One Media package is provided for each sleeve( Fig 5).

Using your fingers, insert the first pad, the gold colored piece into the outlet side of the Sleeve which

is the side with the arrow pointing away (See Figure 6). Using your fingers, put your (8) black colored

pieces into the sleeve one at a time pushing the pieces into the Sleeve as you go. Place the thick

micron pad next to the last black piece. The thin pad goes in last.

Thread the Outlet End Cap back into place. Repeat for each Sleeve from step 5.

Use remaining Silicone Grease to coat the outsides of the copper inlets and outlets.

Make sure each Sleeve is squared up. Put each Sleeve on a flat service and look to see that the elbows line up

with each other (See Figure 7). Adjust the elbows by tightening or loosening each End Cap.

Firmly press your Sleeves back onto your Quadmaxx Pipe Manifolds.

7Slowly turn your main water feed on until water returns to your open faucet and check for leaks.

NOTE: The media contains carbon fines (very fine black powder). After installation, flush the new media for 5 minutes

before using the water.

Figure 5 Figure 6 Figure 7

Rotate Pipe Manifolds so the inlets and outlets are facing you and sit perpendicular with the Backing.

You can use the open end of the Media Removal Tool to make slight adjustments to the Manifolds

(See Figure 1).

Store your set of Sleeve Bypass Caps in the two holesprovided.

Use your fingers to coat the outsides of the copper Manifolds with the Silicone Grease

provided (See Figure 2).

10.

Remove all (8) plastic red caps from the ends of the Sleeves (Shown in Figure 4). They can be discarded.

11.

To ensure that both the inside of each elbow and the outside of the Manifolds are properly coated

with Silicone Grease, put the Sleeve on the Manifold one end at a time (See Figures 5 & 6). Remove

each end and put it back on 2 or 3 times. If needed, see Troubleshooting Guide on the following page

for instructions on removing the Sleeve.

12.

The elbows on each Sleeve are aligned when lines painted on each Sleeve match up by tightening

or loosening each end cap (See Figures 3 & 4). Make sure each Sleeve sits on a flat surface without

rocking. (See bottom of Figure 1).

13.

Using the arrows on the Sleeves to ensure the Media is lined up correctly with the direction of your water

flow, push each Sleeve onto the Manifold one at time sliding each elbow of the Sleeve on simultaneously.

Figure 1 Figure 2 Figure 3

Figure 4 Figure 5 Figure 6

Connection Instructions

Installation of a water shut off valve at the unit is recommended for media replacement changes and

for emergency shut off water.

Turn off your water supply. Turning off your water heater is recommended.

Release water pressure by opening faucet.

Attach water source to Manifold Inlet. Existing Inlet or outlet pipe size smaller or greater than 1” will require

an additional adapter.

You may now turn your water on. Go slowly and check for leaks. Run water for 10 minutes or until

all gray or cloudy water is gone. You may get an occasional gray burst during the first 48 hours. The

water is safe to drink. Turn your water heater on.

Figure 7 Figure 8

Open

Side

Troubleshooting Guide

•Sleeve Bypass Caps are provided should you have a problem (ie. breakage or a

leak). The Caps may be put in place of a Sleeve so that you can still run your

system until you receive replacement parts (See Figure 7).

•To remove a Sleeve or a Bypass Cap from the Manifolds, first release pressure by

both opening a faucet and shutting off water at the house water supply shutoff

valve. Push the Sleeve or Bypass Caps further onto the Manifold to set the

disconnect fittings back into place. The disconnect fittings are part of the elbows.

Put your thumbs on the Sleeve or Bypass Caps, press your thumbs towards the

wall, wrap your fingers around the copper, and slide them towards your thumb

which will pull the disconnect fitting into the elbow. Finally, pull the Sleeve or

Bypass Caps off the Manifold. To remove a Sleeve, you must pull both sides at

once. A Disconnect Clip has been provided should you need assistance (Figure 8).

If your system leaks at fittings: Release pressure by both opening a faucet and

Remove Sleeve and check for burrs and/or dirt. Ensure the elbows are aligned and add additional

silicone to ensure a water tight seal.

After time, If you notice a bad taste or odor, this indicates that the media in the Media is

saturated, and needs to be changed. It is recommended to change every 6 months.

You can order your refills at www.hydrocareusa.com. Save 10% on auto refill subscription.

Contact : HydroCare USA 888 967 9283 or email info@hydrocareusa.com.

Quadmaxx® is tested and certified by WQA to NSF/ANSI 61 for materials safety only.

Quadmaxx® assembled in U.S.A

Inhaltsverzeichnis

Andere HydroCare Wasserfiltersystem Handbücher

HydroCare

HydroCare DUALPLEXX Gebrauchsanweisung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung