HydroQuip 9700 Series Bedienungsanleitung

9700 SERIES - ERROR MESSAGES

To assist the user in identifying problems with the spa, the system will display error

messages in the lower window. These messages will be helpful when communicating

with your local dealer or qualified technician if a problem should arise.

PRESSURE or FLOW SWITCH ACTIVATED - This error will be displayed

only when the pump is not activated. Cycle the pump through Low & High

speeds then off. If the error does not clear this is an indication that the

pressure or flow switch is activated with no water flow.

Contact your local spa dealer

PRESSURE or FLOW SWITCH NOT ACTIVATED - This error will be

displayed while the is pump running. Cycle the pump through Low & High

speeds. If the error does not clear this is an indication that the pressure or

flow switch has not activated although there is water flow.

Contact your local spa dealer

TEMPERATURE SENSOR MALFUNCTION - This error will occur when a

problem with the temperature sensor exists. This error may also occur if the

system is activated while the water temperature is below 35BF.

Contact your local spa dealer

OVERHEAT or HIGH-LIMIT PROTECTION - There are three(3) stages of

over-temperture:

1 - The spa water has exceeded 112BF. The heater, pump and accessory

will be deactivated until the water cools to 109BF. Be sure to check the

actual water temperature with an accurate thermometer.

2 - The spa water has exceeded 119BF. The heater will deactivate while the

pump and accessory will still operate. The blower (if equipped) can be

activated to help cool the water. WATER MUST BE BELOW 119BF AND

POWER MUST BE RESET TO CLEAR THE “HL” ERROR

A dirty spa filter can also cause a restricted flow of water, be sure the filter

is cleaned regularly and ensure all water shutoff valves are open.

If the system has been operating normally until now, the pump may be

overheating the spa. Refer to “Programing Filtration” on page X and reduce

the duration and/or number of cycles per day.

3 - If you’ve eliminated items 1 & 2 as problems, the high-limit sensor may

have malfunctioned.

Contact your local spa dealer

All Universal systems leave configured 120-Volt input power (Option 1).

9700 SERIES - INCOMING POWER WIRING

120-Volt electrical service requires:

Line 1, Neutral and Ground.

(Line 2 to Neutral jumper must be in place

for system to operate properly)

240-Volt electrical service requires:

Line 1, Line 2, Neutral and Ground.

(Line 2 to Neutral jumper must be

removed)

L1 N GR L1 N GR L2

N to L2

Jumper

OPTION 1 OPTION 2

IMPORTANT: Always refer to the product data label (located on top of

control box) for specific electrical information.

It is possible to change the parameters of the system from the spaside control. All circuit presets

have been programmed at the factory. Follow the procedures described below to adjust these

settings.

9700 SERIES - LOW LEVEL PROGRAMMING

PROGRAM KEY

UP/DOWN ARROWS

PROGRAM MODE ICON

PUMP 1

=Press & Hold the Program key for approx 20 seconds. A value of P1_X will appear in the lower window

and the Program icon will appear in the upper window indicating that programming mode is active. (X =

1 or 2 in this case)

=To advance to the next setting press the Program key

=To change a setting Press the Up or Down key accordingly

=After desired changes are made press the Program key repeatedly to advance through the rest of the

settings, exit the programming mode, and reset the system.

DISPLAY: P1_X

VALUE OF X: 1 = Single Speed

2 = Two Speed

DISPLAY: P2_X

VALUE OF X: 0 = Not Installed

1 = Single Speed

2 = Two Speed

DISPLAY: P3_X

VALUE OF X: 0 = Not Installed

1 = Single Speed (30 minute timeout)

2 = Single Speed (5 Min timeout)

DISPLAY: BL_X

VALUE OF X: 0 = Not Installed

1 = Single Speed

2 = Two Speed

3 = Three Speed

DISPLAY: LI_X

VALUE OF X: 0 = Not Installed

1 = 12V Single Intensity (LED Ready)

2 = 12V Three Intensity

3 = (2) Lights - (1) 12V-3 Intensity, (1) 120V

CP must be set to “0”

PUMP 2PUMP 3BLOWER

LIGHT

DISPLAY: O3_X

VALUE OF X: 0 = Not Installed

1 = ON with Filter Cycles

2 = Always ON

3 = Controlled by Filtration Timer

OZONE

DISPLAY: CP_X

VALUE OF X: 0 = Not Installed

1 = 24hr operation (no 4 degree over)

2 = 24hr operation (with 4 degree over)

3 = 24hr operation (with 4 degree over and

over temp filtration cycle)

CIRC PUMP

AUX/FO

DISPLAY: AU_X (5A Max. Load)

VALUE OF X: 0 = Not installed

1 = (1) Component

2 = Fiber Optic Box

3 = (2) Components (Toggled)

HC/LC

DISPLAY: Cu_X

VALUE OF X: 0 = Low Current Mode

1 = High Current Mode

CLOCK

DISPLAY: Ti_X

VALUE OF X: 12 = 12/12hr Time Format

24 = 24 hr Time Format

KEYPAD

DISPLAY: Ts_X

VALUE OF X: 0 = 8 Button

1 = 10 Button

PROGRAMMABLE VALUES

9700 SERIES - BASIC OPERATION

Pump 1 Key: Press this key once to turn Pump 1 on. A second press will turn it off. For dual speed pump operation;

Press this key once to turn Pump 1 onto Low speed, press this key a second time to turn Pump 1 onto High speed, a third

press will turn the pump off. A built-in timer will shut the pump off after 20 minutes of operation unless done so manually.

The Pump 1 Icon will appear on the LCD while the pump is running in High speed and flash while it is in Low speed. If the

filter icon appears, a filtration cycle has begun and you will not be able to turn the pump off.

Pump 2 Key: Press this key once to turn Pump 2 on. A second press will turn it off. For dual speed pump operation;

Press this key once to turn Pump 2 onto Low speed, press this key a second time to turn Pump 2 onto High speed, a third

press will turn the pump off. A built-in timer will shut the pump off after 20 minutes of operation unless done so manually.

The Pump 2 Icon will appear while the pump is running in High speed and flash while it is in Low speed.

Air Blower Key: Press this key once to turn blower onto High speed, a second press will turn the blower onto Low

speed and a third press will turn the blower off. A built-in timer will shut the pump off after 20 minutes of operation unless

done so manually. The Accessory Icon will appear while the blower is running in High speed and flash while it is in Low

speed.

Light Key: Press this key to turn the light onto its highest intensity, a second press will turn the light onto low and a

third press will turn it off. The light will automatically shut off after 2 hours. The Light Icon will appear while the light is on.

Temperature Set Keys: Press the Up arrow key to increase the desired temperature. Press the

Down arrow key to decrease the temperature. The temperature can be adjusted in 1F increments from 59F to

104F (5C to 40C). The new setting will remain on the display for 5 seconds as a confirmation. During this time the

Set Point icon will be appear to let you know this is the desired and not the actual temperature. After 5 seconds the display

will return to the current temperature reading. When the temperature drops to 1F below the set temperature, the heater

will be turned on until the temperature is 1F above the set temperature. The heater icon will appear while the heater is on

and flash when there is a call for heat and the heater has not yet been activated.

Programming Parameters: There are several Filtration parameters that may be programmed. Follow these

procedures to set each parameter: Press and hold the Program Key for 5-seconds, the Program icon ( ) will appear.

You may continue to press the Program key to access the desired Filtration parameter to be modified. Once you have

reached the parameter to be modified, press the Enter (Light) key. Use the Up & Down Arrow keys to adjust the value. If

no key has been pressed for 15-seconds the programming mode is exited. During programming all keys other than the

Program, Enter (Light) and Up & Down Arrow keys will be ignored. Refer to the owners manual for specific filtration and

economy programming details.

85-0066-E REV.03 11/11

PUMP 2 ICON

HEATER ON ICON

PUMP 1 ICON

PROGRAM KEY

ECONOMY/NORMAL

MODE KEY

UP/DOWN ARROWS

LCD WINDOWS

FILTERING ICON

TEMPERATURE SET ICON

ECONOMY MODE ICON

LIGHT/ENTER KEY

AIR BLOWER KEY

PUMP 2 KEY

PUMP 1 KEY

PANEL LOCK

AIR BLOWER ICON

PROGRAM MODE ICON

LIGHT ON ICON

Andere Handbücher für 9700 Series

Inhaltsverzeichnis

Andere HydroQuip Controller Handbücher

HydroQuip

HydroQuip BALBOA BP Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung