HYDROSCAND PowerCut 5-85ot Bedienungsanleitung

PowerCut 5-85OT

USER MANUAL Edition II

2017-09-08

Serial number: _________________

Page 2

PowerCut 5-85OT USER MANUAL EDITION II 2017-09-08

CONTENTS

1. INTRODUCTION........................................ 3

2. GENERAL PRECAUTIONS ............................ 4

3. EQUIPMENT............................................. 5

3.1 WARRANTY....................................... 5

3.2 IMPORTANT...................................... 5

4. MACHINE........................................... 6 - 8

4.1 IDENTIFICATION ............................... 6

4.2 DESCRIPTION .............................. 6 - 8

5. STARTING UP ...................................9 - 10

5.1 OPERATOR POSITION.......................... 9

5.2 STARTING UP.................................... 9

5.3 CUTTING....................................9 - 10

6. MAINTENANCE................................. 10 - 11

6.1 REPLACING THE CUTTING BLADE .........10

6.2 AFTER EACH WORKING SHIFT .............11

6.3 REGULAR MAINTENANCE....................11

7. TECHNICAL DATA.....................................12

8. TECHNICAL DRAWS............................ 13 -39

8.1 WIRING DIAGRAM Y/D STARTER ... 13 - 20

8.2 WIRING DIAGRAM SOFT STARTER . 21 - 27

8.3 PNEUMATIC DIAGRAM .......................28

8.4 TECHNICAL DRAWINGS ............... 29 - 31

Page 2

Page 3

PowerCut 5-85OT USER MANUAL EDITION II 2017-09-08

1. Introduction

The purpose of this manual is to provide the necessary information for competent, safe use

of the hose cutting machine.

This information is the result of continuous, systematic data processing and technical tests

recorded and validated by the manufacturer, in accordance with the internal procedures to

ensure the safety of information: 2006/42/EC.

The information below is intended EXCLUSIVELY for specialized users, capable of

interacting with the product with the utmost safety people, the machine and the

environment, interpreting basic diagnostics of problems and malfunctions and performing

simple checks and maintainance, in full compliance with the instructions given from the

pages that follows and with current health and safety regulations.

The manual does not examine in depth the topics of disassembly and extraordinary

maintainance, as these operations must always be carried out by our authorized Technical

Service.

To handle the machine properly, it is necessary to keep the manual in good condition for

the future. Contact the nearest authorized technical service if you need a new manual or

more complete information.

Before each intervention to the machine or its packaging, read the instructions in the fol-

lowing manual very carefully.

Every operator using the machine, MUST read the following instructions before

operating.

Hydroscand Machine AB declines any responsability for damage to persons, things or to the

machine itself, arising fromits incorrect use, neglience and supercial interpretations of

safety concepts in this manual.

This instruction manual should serve for the duration of the cutting machine´s operating

life and be available for at least 10 (ten) years. We recommend to keep it in a known and

accessible place (possible together with other documents related to themachine).

Page 4

PowerCut 5-85OT USER MANUAL EDITION II 2017-09-08

2. General precautions

Always make sure in advance that the minimum safety, placement and operating standards

are respected, taking note of the environmental conditions, temperature, humidity, ligh-

ting, vibrations, suspended dust and the appropriateness of the area to be occupied.

For unloading from pallet or moving of an unpacked machine, the lifting hole must be used.

Any other lifting device may cause damage to people, property or the machine itself.

The cutting machine is constructed to operate indoors (workshops, industries etc.) where

there is no risk of explosion or re.

Do not combine the machine with other equippment unless you have an approval from the

manufacturer. If other equippment are installed on the machine, or if the machine is com-

bined with other equippment it’s necessary to make a risk analysis and a CE approval for the

whole foundation.

Before cutting the rst hose, make sure that the cutting blade rotates in the correct

direction (see rotation arrow) and that the hose is placed steady towards the adjustable

cutting support. Also make sure that the hose is held steady so that there will be no risk

for injuries or damages. Do not put your hands in the cutting blade working area.

Do not remove the information plates on the cutting machine. Make sure they are readable

and that you are sure about their meaning. Should they deteriorate, replace them immedia-

tely by contacting an authorized Technical Service.

The use of spares that do not respond to the specications listed below, changes or

manipulations - however slight- shall exempt Hydroscand Machine AB from any

responsability regarding the proper use and functioning of the cutting machine and safety

of people and/or property.

It is strictly forbidden to tamper with safety equipment and/or devices.

NOTE !

Any maintenance operations, except for those specically described on the pages of this

manual, must be carried out by skilled personnel co-ordinated by authorized Technical

Service. Dispose of processing waste in compliance with current regulations.

Page 5

PowerCut 5-85OT USER MANUAL EDITION II 2017-09-08

3. The equipment

Our stationary hose cutting machine is supplied ready to use packed on a pallet.

The machine is supplied with an electric cable but without plug and main switch. It’s the

customers responsibility to install the power supply according to present national

regulations. The manufacturer recommends a lockable main switch between the machine

and the mains. PowerCut 5-85OT is prepared with a smoke evacuation connection and if a

smoke evacuation is connected the manufacturer recommends to install a spark lter to

prevent hazards.

NOTE !

The packing material must be disposed according to current environmental protecting re-

gulation.

The machine is supplied initially with:

• Cutting blade HSM 520x4x38 Toothed part No: 90050006.

• Locking tool for changing cutting blade.

• Instruction manual.

• Certicate regarding agreement according to CE-standards.

3.1 Warranty

The cutting machine is guaranteed for one (1) year following the date of purchase; the war-

ranty is valid only if all of the instructions listed on the warranty certicate and in this

manual are fully complied with.

NOTE !

When unpacking the cutting machine, make sure that the machine is in perfect condition

and that the package contains the parts described. Hydroscand Machine AB does not re-

spond for errors or missing parts not reported to Hydroscand Machine AB following eight

(8) days after shipment.

3.2 Important

The hose cutting machine is designed, manufactured and protected for cutting 1-, 2- ,4-

and 6-layers hydraulic hose with dimension from 3/16” up to 3”.

Any other use is excluded by Hydroscand Macine AB, who shall be exempt from any

liability for damage to people, property or the machine itself, caused by improper use. Do

not leave the cutting machine idle running for longer periods, without cutting anything.

Do not cut solid steel, wood or other unknown material, that can cause damage to

people, property or the machine itself.

Page 6

PowerCut 5-85OT USER MANUAL EDITION II 2017-09-08

4. The Machine

4.1 Identication

The information for identifying the machine is found on the plates, located outside of

the cutting machine. This essentially includes:

• Manufacturer

• Serial number

• Year of manufacture

• Voltage (V)

• Hertz (Hz)

• Amperes (A)

• Weight

The CE- approval plate is located back, under the electric box.

NOTE !

It is strictly forbidden to remove or damage the plate. Should this happend, always

contact an authorized Techical Service only.

For any information and/or technical explanations regarding the cutting machine, always

indicate:

• Model

• Serial number

• Edition and preparation date of the instruction manual

4.2 Description

The stationary hose cutting machine consists of one unit, equipped with a pneumatic

cylinder, which is manouvered by a foot pedal and ap doors that are pressed down by the

hose during the cutting process. The unit is also equipped with a connection for a smoke

evacuator (option), and as standard a toothed cutting blade assembled on the machine.

The machine is equipped with an air pressure regulator and lter. Do not start the machine

before the air pressure has reached min. 5 bar.

The hose cutting machine must only be used for hydraulic hoses compatible with the

specications below. Follow the environmental conditions and limitations recommended by

Hydroscand Machine AB and current health and safety regulations.

NOTE !

The descriptions includes the use for which the machine has been designed, built

and protected. Any other use or failure to comply with the technical parameters

listed below, may constitute a hazard to people and/or property.

Page 7

PowerCut 5-85OT USER MANUAL EDITION II 2017-09-08

1 2

11 10 9

Page 8

PowerCut 5-85OT USER MANUAL EDITION II 2017-09-08

1. Foot pedal

2. Waste box

3. Adjustable feet

4. Motor

5. Bend support

6. The Hold counter button

7. The emergency stop push button

8. The on/off button

9. Counter with reset button

10. Hose bending system on/off

Hose bending system on/off. On when cutting 1 ½” and above, multispiral hoses. On when

cutting 2” and above, braided hoses.

11. Cuttin stroke switch

A three ways switch. Preset return levels for the bending unit. The cylinder is stopped at

specied levels to prevent it from doing full return strokes when not necessary.

12. The Front hatch

The front hatch is operated by a pneumatic cylinder located at the top of the machine. The

hatch has a two way switch (Auto and Down). When “down” is chosen the hatch stays down

at the whole cutting process. When “auto” is set the hatch is normally open but will auto-

matically go down when the foot pedal is pressed to start the cut. The hatch will come

down as a protection before the hose will be pressed down and cut. The hatch will automa-

tically open after the cut is made.

13. Cutting speed

Adjust according to hose diameter, reinforcement, material etc.

14. Lifting hole

Page 9

PowerCut 5-85OT USER MANUAL EDITION II 2017-09-08

5. Starting up

Before plugging in the machine on the electrical net, ensure that the voltage corresponds

to the voltage on the machine. Make sure that air is supplied to the machine and that the

pressure is sufcient. Do ALWAYS use goggles and hearing protections when using the

machine. Keep ngers and other body parts off from areas where the machine is making

linear and circular movements. Do ONLY use the machine to cut hydraulic hoses. When the

machine is intended for cutting other kinds of hoses do ALWAYS contact Hydroscand Mach-

ine AB for consultation in the matter. Ensure that every possible safety precaution is taken

before starting up the machine. Check the cutting blade for possible damages, that it is

securely tightened and that it can rotate freely. Check that the hose bend system is working

properly. When cutting hoses with outer diameters exceeding 2” make sure that the pre-

bend help system is working properly. When the machine has started ensure that the direc-

tion of rotation of the cutting blade is all right. The upper edge of the cutting blade must

rotate towards the back part of the cutting machine. If the machine is

vibrating abnormally, STOP THE MACHINE IMMEDIATELY and check the reason of the vibra-

tions.

5.1 Operator position

The operator must be in such a position that he is ensuring safety and that the cutting is

easliy observed.

5.2 Starting up

Release the emergency button by turning it clock-wise. Select your cutting speed.

5.3 Cutting

Press the start button and then press the foot pedal down. You are ready to cut !

Minimum cutting length is 130 mm and the cutting speed is adjusted according to the

actual hose dimension in process.

…hoses of dimension above 2” up to 3”, shall the cutting supports NOT

be used.

NOTE!

Always adjust the cutting speed according to hose dimension in process. This ensures

that the cutting blade lifetime is optimal, that it stays sharp.

Page 10

PowerCut 5-85OT USER MANUAL EDITION II 2017-09-08

6. Maintenance

WARNING!

When doing maintenance on the machine do always make sure that the machine is unplugged from

the electrical net, pneumatic and do always press down the emergency switch. Taking these safety

measurements ensures that no electrical tension is supplied to the machine that could make it start.

Do always use protecting gloves when changing cutting blade. Do always use protective clothing and

protective shoes to make certain that no injuries will happen if dropping the cutting blade on the

body or feet.

6.1 Replacing the cutting blade

1. Unplug the machine and press down the emergency switch.

2. Open the lid on the left side of the machine stand and

open the front hatch.

3. Loosen the socket set screws and the socket head cap screws,

outer carrier behind the lid.

4. Dismantle the old blade and assemble a new one. Only use by

Hydroscand Machine recommended cutting blades.

5. Assemble the centre socket head screw tightly;

torque 80 Nm. Tighten the two socket set screws to

secure the cutting blade.

6. Reassemble the lid and the front hatch. Make sure that all screws are

severally tightened. The correct torque to use is 24 Nm. Use a torque

wrench to be sure the screws are correct tightened.

New cutting blades must be used with reduced speed

for the feeding at about 200 cut. When the running-in

has been done the cut can be performed at normal speed.

As a basic rule the blade should never be overheated.

If excessive smoke or heat is generated or if the motor stalls

the cut sequencemust be interrupted immediately and the

cause found.

Reassemble the lid and the front hatch. Make sure that all screws are

severally tightened. The correct torque to use is 24 Nm. Use a torque

Lid

Front hatch

Inhaltsverzeichnis

Andere HYDROSCAND Cutter Handbücher

HYDROSCAND

HYDROSCAND MaxiCut 5-60 Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

Makita

Makita DCS552 Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung