Hyperion HYP-GTW-G2 Bedienungsanleitung

Hyperion Gateway Installaon Guide www.wrensolutions.com 7L776 Rev A 190510

INSTALLATION GUIDE

HYPERION GATEWAY

HYP-GTW-G2

Hyperion Gateway Installaon Guide www.wrensolutions.com 7L776 Rev A 190510

ABOUT THIS DOCUMENT

This document pertains to installation of the Hyperion Gateway (IDS-

CCULD). Before installation, please familiarize yourself with this

installation guide and review the Hyperion User Guide to understand

system configuration and setup. Supporting documentation can be

found in the Wren Support Portal at www.wrensolutions.com/support.

PRODUCT MODIFICATIONS

This product is to be installed and used for the specific purpose for

which it was designed. It is not to be modified or serviced by anyone

other then Wren. Unauthorized changes or modifications to the

product will result in the warranty being voided and could possibly

invalidate regulatory certifications.

WARRANTY

Unless otherwise noted, all products are covered by Wren's Standard

Limited Manufacturer's Warranty as set forth in the current version of

Wren's Terms and Conditions

INTELLECTUAL PROPERTY RIGHTS

Wren maintains certain intellectual property rights that may pertain to

this product. To see a list of our patents, please refer to our

TRADEMARK ACKNOWLEDGMENTS

Wren®. the Wren logo, Hyperion® and the Hyperion logo are

trademarks of Wren. The trademarks that are followed by ® are

registered trademarks in the U.S. All other trademarks and/or

registered trademarks mentioned herein are properties of their

respective owners and are for reference purposes only. The use of

such third party trademarks does not indicate any affiliation with or

NOTICES

RF Exposure for FCC

WARNING: To satisfy FCC RF exposure requirements for mobile

transmitting devices, a separation distance of 31 cm or more should be

maintained between the antenna of this device and persons during

device operation. To ensure compliance, operations at closer than this

distance is not recommended. The antenna used for this transmitter

must not be co-located in conjunction with any other antenna or

transmitter.

RF Exposure for IC

WARNING: To satisfy IC RF exposure requirements for mobile

transmitting devices, a separation distance of 44 cm or more should be

maintained between the antenna of this device and persons during

device operation. To ensure compliance, operations at closer than this

distance is not recommended. The antenna used for this transmitter

must not be co-located in conjunction with any other antenna or

transmitter.

AVERTISSEMENT: Pour satisfaire IC RF exigences d’exposition pour

les appareils mobiles de transmission, une distance de séparation de 44

cm ou plus doit être maintenue entre l’antenne de cet appareil et des

personnes pendant le fonctionnement de l’appareil. Pour assurer la

conformité, les opérations au plus près que cette distance ne sont pas

recommandés. L’antenne utilisée pour cet émetteur ne doit pas être

situé en conjonction avec une autre antenne ou émetteur.

(800) 881-2249

EXTENSION 4

PRODUCT SUPPORT

For comprehensive product support including manuals, FAQs and

troubleshooting, visit our customer support portal

WWW.WRENSOLUTIONS.COM/SUPPORT

Hyperion Gateway Installaon Guide www.wrensolutions.com 7L776 Rev A 190510

Prior to installation, verify that all hardware is included. If there are missing components, please contact Wren.

COMPONENT LIST

Hyperion Gateway 24VDC Power Supply Mounting Bracket Antenna (x2)

REQUIRED TOOLS AND ACCESSORIES

#2 Phillips screwdriver Drill Cables (CAT5 or higher)

DEVICE OVERVIEW

1. SD Card Slot

2. Hyperion Device Ports

3. Digital Input/Output

4. Audio Out

2 3 4 5 6 7 8 9 10

NOTE: CABLING SHOULD MEET THE T-568A WIRING STANDARD AND ALL CABLES SHOULD BE TESTED BEFORE USE.

IMPROPER CABLING COULD DAMAGE THE GATEWAY AND VOID PRODUCT WARRANTY

5. Hyperion Radio Antenna

6. Audio Channel Volume Control

7. DC Power Input

8. Network Connection

9. USB Potts

10. Wi-Fi Antenna

Hardware

24VDC

Hyperion Gateway Installaon Guide www.wrensolutions.com 7L776 Rev A 190510

BEFORE BEGINNING INSTALLATION, PLEASE

MAKE SURE OF THE FOLLOWING:

• YOU HAVE READ THE INSTALLATION GUIDE

• YOU HAVE READ THE USER GUIDE

• YOU ARE ONLY USING THE HYPERION POWER SUPPLY

• YOU HAVE TESTED AND CERTIFIED ALL CABLE CONNECTIONS

FOR PROPER PINOUT ALIGNMENT PER T-568A STANDARD

IMPROPER CABLING COULD DAMAGE THE

GATEWAY AND VOID PRODUCT WARRANTY

Hyperion Gateway Installaon Guide www.wrensolutions.com 7L776 Rev A 190510

IDENTIFY AN APPROPRIATE MOUNTING LOCATION

Table Mount

The Gateway is equipped with rubber feet pre-installed

for table mounting applications. If table mounting, the

wall bracket will not be needed.

Wall Mount

The Gateway should be mounted to a structurally solid

wall surface using the included bracket. Mount by using

the appropriate fasteners and anchors for the mounting

surface. (Fasteners and anchors are not provided).

3 CONNECT ETHERNET

NOTE: NETWORK CONNECTIVITY IS REQUIRED FOR

CUSTOM CONFIGURATION, BUT NOT REQUIRED FOR THE

GATEWAY TO OPERATE.

Connect the Ethernet cable to the

provided Ethernet network socket as

depicted to the right.

4 CONNECT HYPERION DEVICES

Before connecting cables from devices, refer to the Gateway Configuration Plan to ensure Hyperion devices are

plugged into their respective ports.

For Gateways that were not factory-configured, please complete the Gateway Configuration Plan before making any

connections.

NOTE:

• THESE ARE NOT ETHERNET PORTS

• ENSURE THAT ALL CABLING CONNECTIONS HAVE BEEN CERTIFIED BEFORE

ATTACHING TO THE GATEWAY

• IMPROPER CABLING COULD DAMAGE THE GATEWAY AND VOID PRODUCT

WARRANTY

• CABLES RUNS HOULD NOT EXCEED 300 FEET

NOTE:

• THE LONGER ANTENNA CONNECTS TO THE

“HYPERION” JACK

• FOR BEST RESULTS, THE ANTENNA SHOULD BE POINTED

AS VERTICALLY AS POSSIBLE

CONNECT ANTENNAS

Hand-tighten the appropriate

antenna to the corresponding

jack until snug.

Do not over-tighten.

Hyperion Gateway Installaon Guide www.wrensolutions.com 7L776 Rev A 190510

CONNECT DIGITAL INPUT AND OUTPUT RELAY

6 CONNECT AUDIO

Digital Input

The Digital Input can be used for connecting external devices to the Gateway. It

is activated when a ground signal is sensed.

Output Relay

For connecting external devices, such as LEDs or sirens.

• It can be wired as Normally Open or Normally Closed

• The Relay is rated for 250VAC/100VDC, 10 amps

The gateway supports two, independent audio channels, each with separate

connection ports and volume adjustment.

Attach speaker wires to the Gateway, making sure to note polarity.

To adjust volume, use a Philips screwdriver and turn the potentiometer

accordingly. Volume can also be adjusted via the gateway software. More

information can be found in the Gateway User Guide.

NOTE: WERECOMMEND USING 18 AWG WIRE OR LARGER AND AMAXIMUM

RUN OF 500 FEET IN ORDER TO MAINTAIN AUDIO VOLUME AND CLARITY

NOTE: DONOT APPLY ANY VOLTAGE TO THE DIGITAL INPUT OR DAMAGE WILL

OCCUR TO THE DEVICE, WHICH IS NOT COVERED UNDER WARRANTY

7 CONNECT POWER

Connect 24VDC from the supplied

power supply to the power jack.

Power can be confirmed by observing

the green power light next to the

power jack.

NOTE: ONLY USE THE SUPPLIED 24VDC POWER SUPPLY

OR IMPROPER POWER MAY BE APPLIED TO THE GATEWAY

WHICH COULD NEGATIVELY AFFECT PERFORMANCE.

REFER TO GATEWAY CONFIGURATION

PLAN FOR SYSTEM TESTING

8 SYSTEM TEST

Inhaltsverzeichnis

Andere Hyperion Tor Handbücher

Hyperion

Hyperion IDS-CCULD Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung