HYPERVOLT Home 3.0 Bedienungsanleitung

Home 3.0

Quick

Start

Guide

IMPORTANT - PLEASE READ

This is a basic guide, it must not be used as a

substitute for the full manual which should be

consulted before installation.

This Guide MUST be handed to the end user.

Overview Internal Layout Overview Key Components

1Incoming Supply Connections - LIVE, NEUTRAL & CPC (Earth)

We recommended using stranded cables with ferrules. Tighten to 2 Nm.

2Tethered Cable Connections - This is where the tethered car charging cable is

connected. If you replace this cable remember to put the Blue & Brown wires back

through part , not the Green & Yellow.

3CP Connection - This is where the control pilot from the car charging cable is

connected. It goes in the right side, push the tab to insert.

4CT Connection - The CT clamp supplied should be connected here, extend the

cable as necessary using HyperConnect or CAT cable. Use the Left plug for ALM, The

Right Plug is for Additional monitoring (see main manual).

5RJ45 Connection - For a hardwired internet connection plug in here. You only need

to use the Orange & Green pairs of a CAT cable in the standard T-568B conguration.

7Derating DIP Switches - For hard setting the Maximum charging limit (See page 6).

Soft set in the App. (Factory set to 32A)

8Sensing Device (RCD-DD) - Internal 6mA DC sensor. You must t an external AC

Sensing “A” Type RCD.

10 Cut for Rear Entry Gland - Drill out if required, 25mm Max Ø, seal accordingly.

Original entry hole must be sealed if this one is used.

6ALM Adjustment Dial - For setting the Automatic Load Management. (See page 6).

9LED Front Plate Connection - This is where the LED lights plug in.

11 Additional Cable Entry - Drill out for Band 1 Cables, 20mm Max Ø.

12 Main Brain - Where all the HyperMagic happens.

13 HyperConnect Cable - Live, Neutral & CPC + CAT 5 (4mm or 6mm).

Available directly from Hypervolt.

4 5

Installation Electrical Safety

Your Hypervolt comes with built-in safety protection. It is imperative

to understand and include the additional external safety protection all

electric vehicle charging points require.

Hypervolt installations must only be done by quali ed, registered

electricians. All installation work for safety & preservation of warranty

must be compliant with BS7671 as amended.

External Equipment Required

Residual Current Device

The Hypervolt Home 3.0 shall be protected by an external RCD device. This should

as a minimum be an Individual Type “A” Double Pole Device. Only one external

RCD should be inline and never a Type “AC” .

Overcurrent Protection

The Hypervolt Home 3.0 shall have external overcurrent protection no greater than

40A. This can be in the form of an RCBO or if using a separate RCD this can be an

MCB. We recommend using a 40A device when the Hypervolt is used on it’s

maximum output setting (factory set)

Surge Protection Device (SPD)

We recommend that all Hypervolt’s shall be protected by an external SPD to prevent

transient overvoltages causing the built-in safety services to fail.

Consideration dependant on external factors should be given as to if a Type 1 or

Type 2 device would be more suitable.

Built In

PEN Fault Protection

The Hypervolt Home 3.0 comes with built in PEN fault protection for additional

safety, should a fault occur with the electrical distributors network. It eliminates the

need to install an earth rod.

Residual DC Device

The Hypervolt Home 3.0 has a built in DC RCD-DD ( ) that can protect against DC

fault currents over 6mA.

Installation Connect the supply

Connection to an Electrical Supply (230V)

HyperConnect

Below is the most commonly used & recommended method of connecting your

Hypervolt to an electrical supply.

We recommend using HyperConnect cable for installing Hypervolt EV Chargers, it

contains power, data and CT connection wires in one neat easy to  t cable.

We do not recommend the use of NYY-J Cable.

4 & 6mm Non & SWA Live, Neutral,

CPC & Cat 5e

The White Wire from the CT goes in the Left &

Black in the right. Extend as necessary, a Brown

pair of a CAT cable is used in this example.

CT Plug

RJ45 Plug

(T-568B)

CT Plug

The CT clamp must be installed

to measure the total supply load

with the arrow pointing in the

direction of current ﬂ ow.

Using the Charger Connecting Online

To adopt your Hypervolt charger to an App account and get it online,  rst download

the Hypervolt App (QR Code on back page) then follow these 4 steps:

‘Sign Up’ tab and then use the ‘Sign In’ tab to login.

Adopt Next you need to ‘adopt’ your charger by choosing an ‘Available’ Hypervolt on

the ‘Select your charger’ page.

Connect to your Wi-Fi Next select your Wi-Fi connection and enter the

password.

Success ! Once your Hypervolt has connected the pulsing white ring around the

edge of the cover will turn solid blue. You can now use the App with all its great

features.

Hypervolt Trusted Installers have access to an Installers App for this process.

Installation Setting ALM and Current

Adjust the ALM

Hard setting the current limit

The ALM (Automated load management) is used to provide protection to the incoming

supply by preventing charging above 6A at an upper limit set by dial ( ).

The hard current limit sets the maximum current the Hypervolt will charge a

vehicle at. Set the dip switches ( ) accordingly. The switches come factory set

to 32A (All ‘oﬀ ’ to the right).

The dial is small so double check you have set it correctly, The arrow in the picture below

shows where the dial is pointing, 5 in this case.

Note:

The current limit can be soft set in the App, a hard set overrides a soft set.

8: 100A

7: 80A

6: 60A

Note:

Installation LED Statuses

* If your Hypervolt is continually displaying a red fault status please contact our support team.

The LED coloured light status show what action your charger is performing. After your Hypervolt charger has been installed and setup, below are the diﬀ erent

charging options that you can choose to suit your needs and get you started:

If you have selected an LED Mode or dimmed to 0% the status colour will show brieﬂ y before

returning to 0% or the mode colours.

Your Hypervolt comes with a pre-set

default schedule (23:00 - 06:00). On the

App Home page tap on

to swap to Plug and Charge mode.

If you have solar panels change the

charging mode to best suit your needs.

Standby

Plug & Charge

Not Online

(Pulsing White Ring with

Solid Blue Bolt)

Paused (Pulsing)

Stopped (Flashing)

Delayed Start

(Random Start On)

Charging Standby

Schedule Charge

Waiting to

Schedule Charge

LockedWaiting for Solar

(Super Eco Mode)

Unauthorised Use

(Flashing)

*Fault

Using the Charger How to charge

Plug and Charge

Scheduled Charging

Simply plug the charging cable into

your EV. When you want to stop

charging tell your car to unlock the

cable then unplug.

You may want to only charge at

speci c times, maybe to take

advantage of cheaper electricity

tariﬀ s.

You can do this using the ‘schedule

charge’ activation mode.

Edit the schedule to match your

prefered charging times and tap

save. Your Hypervolt will turn purple.

Now when you plug your EV in it will

only charge within your set times.

App Home page tap on

Note:

Smart Charging Regulations What you need to know

Default Schedule

Random Start

The latest UK ‘Electric Vehicle Smart Charge Points Regulations’ (No. 1467) help to

manage the increased electrical demand as more people move to the advantages of

electric transportation. In line with these regulations the Hypervolt comes out of the

box with two default settings.

Here’s what you need to know:

Your Hypervolt will come with a pre set oﬀ peak

schedule to encourage charging during lower

demand times (23:00 - 06:00).

You can opt out by either changing the schedule,

choosing Plug and Charge or unselecting “Default

Schedule” on the ‘Your Hypervolt’ page.

Your Hypervolt will come pre set to random start every

time a charging session begins in Boost Mode, whether

that be from a Schedule or a straight Plug and Charge.

The charge will be delayed anytime up to 10 minutes.

The charging indicator will show as “Waiting” with a delay

countdown above.

You can opt out of this by unselecting it on the ‘Your

Hypervolt’ page.

Smart Charging Regulations What you need to know

How cyber secure is my device?

How long will your Hypervolt device be supported for?

How to delete your

personal data from

the device

The Hypervolt Home 3.0 uses state of the art encryption both on the device and

embedded in our software, resulting in a very cyber secure product. There are no

additional steps you need to take to ensure your device is secure apart from the

standard actions such as not sharing your Hypervolt account login details.

Hypervolt will issue updates to your Home 3.0 for a minimum of 3 years from the

date of purchase.

Whilst a Hypervolt Home

3.0 does not store personal

details about yourself, it does

store information about how

you use your charger, wi

credentials and other

information that the charger

needs to support its features

and maintain functionality.

You can delete any data

stored on your charge point

by going into your app then

settings -> ‘Wipe Device Data’.

Need more support?

Your installer must register the installation to start the Hypervolt warranty.

Go to hypervolt.co.uk/support for

lots of additional support materials.

Hypervolt Home 3.0 Quickstart guide Version 2.0. Please note this Quick Start guide is subject to change.

0333 090 3093

support@hypervolt.co.uk

www.hypervolt.co.uk

30 Churchill Pl, London E14 5RE,

United Kingdom

Your Hypervolt’s details

Scan me to register

your Hypervolt and

start your warranty

App

Want to Control your

charger with the app,

Scan me.

Full Manual

Scan me to Download

the Full Manual

Andere Handbücher für Home 3.0

Inhaltsverzeichnis

Andere HYPERVOLT Autobatterieladegerät Handbücher

HYPERVOLT

HYPERVOLT Home 3.0 Bedienungsanleitung

Beliebte Autobatterieladegerät Handbücher anderer Marken

ULTIMATE SPEED

ULTIMATE SPEED ULGD 3.8 A1 Bedienungsanleitung

Growatt

Growatt THOR 11AS-S/P Bedienungsanleitung

Ingeteam

Ingeteam Ingerev Garage Bedienungsanleitung

DEFA

DEFA Power 715000 Bedienungsanleitung

iTechworld

iTechworld iTECHDCDC20 Bedienungsanleitung

EM2GO

EM2GO Take Bedienungsanleitung

Booster

Booster TRUCK PAC ES1224 Bedienungsanleitung

Teison

Teison TS-PEC-002 Bedienungsanleitung

Schumacher

Schumacher SI-200A Bedienungsanleitung

YingLi

YingLi YLEV50A-L3 Bedienungsanleitung

ABL

ABL eMH1 WALLBOX Bedienungsanleitung

GARO

GARO LS4 Wallmounted Kurzanleitung

CTEK

CTEK MXS 5.0 CHECK Bedienungsanleitung

Hama

Hama 54183 Bedienungsanleitung

Cartrend

Cartrend DP 4000 Bedienungsanleitung

Ryobi

Ryobi P131 Konfigurationshandbuch

FLUXE

FLUXE M3P U Series Bedienungsanleitung

BMW

BMW Wallbox Pro Bedienungsanleitung