HYT TR-50 Series Bedienungsanleitung
TR-50
PORTABLE REPEATER
Contents
General……………………………………………………………………………..1
Brief Introduction…………………………………………………………………..2
Theory of Operation………………………………………………………………4
Alignment & Calibration…………………………………………………………..6
Part List 1………………………………………………………………………….9
Assembly and Disassembly for Repair………………………………………11
Exploded View……………………………………………………………………12
Part List 2…………………………………………………………………………13
Packing……………………………………………………………………………14
PCB Board View…………………………………………………………………15
Schematic Diagram……………………………………………………………...17
Specifications…………………………………………………………………….19
TR-50 General
- 1 -
General
Manual Scope
This manual is intended for use by experienced technicians familiar with similar types of
communication equipment. It contains all service information required for the equipment and is current
as of the publication date.
User Safety Information
The following precautions are recommended for personnel safety:
zDO NOT transmit until all RF connectors are verified secure and any open connectors are
properly terminated.
zSHUT OFF and do not operate this equipment near electrical blasting caps or in an explosive
atmosphere.
zWhen in vehicles with an airbag, do not place a repeater in the area over an airbag or in the airbag
deployment area.
zDO NOT expose the repeater to direct sunlight for a long time nor place it close to a heating
source.
zDO NOT use any repeater with a damaged antenna. If a damaged antenna comes into contact
with your skin, a minor burn may result.
zThis equipment should be serviced by a qualified technician only.
TR-50 Brief Introduction
- 2 -
Brief Introduction
1. LED Indicator
The following table indicates LED indication and corresponding radio status.
LED Status
Red Power on
Green Receive (or in battery save mode)
Blue Transmit
2. Power /Volume Control Knob
Rotate the Power/Volume Control Knob clockwise until a “click” is heard to turn the repeater on. Then
the LED turns red when the power is on. Rotate counter-clockwise to turn the repeater off until a “click” is
heard. When the repeater is on, turn the Knob to adjust volume. (Suggestion: adjust volume to the
lowest while Monitoring is unnecessary.)
3. RJ45 Programming I/O Port
Used by the dealer to program the repeater’s receiver and transmitter respectively.
4. Speaker
Used to monitor the communication status of current channel.
5. Rx Antenna Connector
N/F type RF connector.
6. Tx Antenna Connector
N/F type RF connector. Applied as antenna port when duplexer is installed.
TR-50 Brief Introduction
- 3 -
7. AC Power Inlet
After correctly connecting AC power supply, turn on the switch to enter AC power supply mode.
8. AC Power Switch
9. DC Power Inlet
The float charging function will operate in AC power supply mode with external gel cell batteries
connected. When AC mains power is lost, it will auto-revert to the back-up battery supply without
mechanical relay.
TR-50 Theory of Operation
- 4 -
Theory of Operation
I. Power Control
The control board draws a general 13.8V dc power supply, which is converted through U1, a 3-terminal
regulator, to 8.0V dc for the receiver and transmitter.
Fig. 1 Power Supply Block Diagram
II. Relay Control
When a valid signal is detected, the COR goes low and trigger PTT of the transmitter. At the same
time, the audio output from discriminator is routed to MIC input of the transmitter. The trimmable
resistor VR3 is used to adjust the receive audio output to the proper level for transmit audio deviation.
III. Float Charging Function
The TR-50 provides selectable AC (100-240V ac) power supply. Normally users can equip battery
back-up system connected to the external DC jack with floating charge function in the mean time. This
provides auto-revert to DC battery once the AC mains fails.
IV. Fan Control
This repeater provides three options of cooling fan control: PTT controlled, temperature controlled and
continuous operation. The power supply of the fan is controlled through a 5V voltage detector,
HT7050A. When the input is above 5V, the output is high-Z; when lower than 5V, the output goes low.
TR-50 Theory of Operation
- 5 -
V. AF Amplification
The receive audio is routed to another AF amplifier NJM386M, which is convenient for the users to
monitor the activities of current channel.
VI. Definition for control ports
The definition of all the pins goes as follows:
1. J3 1pin——NC
2pin——TLED-
3pin——MIC+ Transmitter
4pin——PTT
5pin——TLED+
6pin——RLED+
7pin——SP+
8pin——RLED- Receiver
9pin——RxAF
10pin——COR
2. J6
1pin——ETxD
2pin——ERxD Transmitter
3pin——ATxD
4pin——ARxD Receiver
3. RJ45 EXT
1pin——ARxD
2pin——MIC
3pin——ATxD
4pin——ERxD
5pin——GND
6pin——ETxD
7pin——EXTPTT
8pin——SB+（8V）
TR-50 Alignment & Calibration
- 6 -
Alignment & Calibration
I. Required Test Instrument
1. DC power supply 1 set
1）Output range: 12~15 VDC (Minimum); output current: 3 A or more
2）Specified output: 13.8 VDC
3）The output should be stable, with minimal ripple & noise.
2. Ammeter 1set
3. Digitalvoltmeter 1set
4. Radio communication test set 1 set (with duplex function)
II. Test and Adjustment
1. Power supply
Measurement Adjustment
Item Condition Test
Instrument Test Point Part Method
Specification/
Remarks
DC output
voltage Digital
Voltmeter
DC output
terminal
Potentiometer
in Switch
power supply
Use ceramic
adjuster to
adjust till the
voltage is
within
requirement.
13.8±0.2V
2. Power Supply for receiver and transmitter
Measurement Adjustment
Item Condition Test
Instrument Test Point Part Method
Specification/
Remarks
Power Supply
Digital
Voltmeter VDD VR1
Use ceramic
adjuster to
adjust VR1 till
the voltage is
within
requirement.
8.0±0.2V
TR-50 Alignment & Calibration
- 7 -
3. Relay Component (Note: Before adjustment, make sure the antenna (dummy load)
are properly connected and space-isolated)
Measurement Adjustment
Item Condition Test
Instrument Test
Point Part Method
Specification/
Remarks
Operation
Frequency
PC operation
system:
WIN98SE
/WIN2000
Programming
software:
HT-50E
RJ45
Programming
port
Receiver:
1CH
455.0125MHz
2CH
455.0125MHz
CTCSS：67.0Hz
3CH
455.0125MHz
CDCSS：025
Transmitter:
1CH
465.0125MHz
2CH
465.0125MHz
CTCSS：67.0Hz
3CH
465.0125MHz
CDCSS：025
Relay
deviation
Turn to CH1 and
enter duplex
mode. With
Transmitter
connected to
“RF in” port and
receiver to “Dual
out” port. Align
the output of
“RF GEN” to
455.0125MHz。
BPF:0. 3~3KHz
AF OUT:
1KHz/150mV
Antenna VR3
Use ceramic
adjuster to
rotate VR3
until the
deviation is
within
requirement.
Frequency
deviation:
3.0±0.2KHz
Tx Power
Turn to CH1,
press PTT key
on handheld
microphone to
transmit (or
check Tx power
in duplex mode)
Antenna Check
Power Output:
4.5±0.5W
TR-50 Alignment & Calibration
- 8 -
Duplex
sensitivity
Turn to CH1,
and operate
in duplex
mode
BPF:0.
3~3KHz
AF OUT:
1KHz/150mV
Antenna Check
Sensitivity squelch on
transceiver:
-119±3dBm
Sensitivity squelch
off: -120±3dBm
Andere Handbücher für TR-50 Series
1
Inhaltsverzeichnis
Andere HYT Repeater Handbücher
