Hytera TC-600 Bedienungsanleitung

－1 －

Contents

General………………………………………………………………………………2

Brief Introduction………………………………………………………………….3

Software Specification……………………………………………………………5

Circuit Description……………………………………………………………….11

CPU Pins…………………………………………………………………………...16

Part List 1………………………………………………………………………….18

Adjustment Description…………………………………………………………30

Disassembly and Assembly for Repair……………………………………….33

Exploded View…………………………………………………………………….36

Part List 2…………………………………………………………………………37

Packing…………………………………………………………………………….39

PC Board View……………………………………………………………………40

Block Diagram…………………………………………………………………….42

Schematic Diagram………………………………………………………………43

Specifications…………………………………………………………………….44

TC-600 General

－2 －

General

Manual Scope

This manual is intended for use by experienced technicians familiar with similar types of communication

equipment. It contains all service information required for the equipment and is current as of the

publication date.

User Safety Information

The following precautions are recommended for personnel safety:

DO NOT transmit until all RF connectors are verified secure and any open connectors are properly

terminated.

SHUT OFF and do not operate this equipment near electrical blasting caps or in an explosive

atmosphere.

When in vehicles with an airbag, do not place a portable radio in the area over an airbag or in the

airbag deployment area.

Do not expose the radio to direct sunlight for a long time nor place it close to a heating source.

Do not use any portable radio with a damaged antenna. If a damaged antenna comes into contact

with your skin, a minor burn may result.

When transmitting with a portable radio, hold the radio in a vertical position with its microphone

about 5 centimeters away from your mouth.

If you wear a portable radio on your body, be sure to keep the antenna at least 2.5

centimeters away from your head or body when transmitting.

This equipment should be serviced by qualified technicians only.

TC-600 Brief Introduction

－3 －

Brief Introduction

1. Antenna

Used to transmit/receive signals.

2. LED Indicator

The light will glow red during transmission and glow green during receiving. During transmission,

the light flashes red when the battery voltage is low.

3. Channel Selector Knob

4. Power/Volume Control Knob

Rotate the Power/Volume Knob clockwise until a ―click‖is heard to turn the radio on, fully counter

clockwise until a ―click‖is heard to turn the radio off. When the radio is on, turn the knob to adjust

volume.

5. PTT Key

Press and hold PTT key to talk, release to receive.

6. Function Key

The key can be programmed to access the radio features with the preset type of key pressing

through the programming software.

7. Microphone

Used to input sounds.

8. Speaker

Used to output sounds.

TC-600 Brief Introduction

－4 －

9. External Jack (for external earphone or radio programming)

Rotate the jack cover and insert accessory plug, or insert programming cable into the jack to

program the radio via programming software.

10. Battery

11. Belt Clip

Used to clip radio on your belt.

12. Battery Latch

Used to fasten and remove the battery.

13. Charging Connector

Insert the battery into the charger; connect the charging connectors with those on the charger to

begin charging.

TC-600 Software Specification

－5 －

Software Specification

Radio Feature Description

1. Use Channel Selector Knob to choose from 15+1(Scan) channels

2. Monitor

3. CTCSS/CDCSS Encode & Decode

CTCSS: 38 groups

CDCSS: 83 groups

4. Wideband (25KHz) / Narrowband (12.5KHz)

5. Channel Scan (Priority channel and Revert channel available)

6. Battery Save feature (Dealer programmable)

7. Time-out Timer (TOT)

8. Squelch Level (1-9)

9. Low BatteryAlert

10. Programmable Function Key

11. High/Low Power

12. 2-Tone Encode & Decode

13. DTMF ANI

14. Model Set Mode

15. PC Programming & Adjust Mode

16. Manual Adjust Mode

17. User Wired Clone Mode

18. Factory Wired Clone Mode

TC-600 Software Specification

－6 －

Radio Modes

Mode

Entry for Mode Startup

Audible & Visual Indicator

User Mode

Disconnect the SELF points and then turn the

power on

Power-on alert tone (one long Beep)

Model Set Mode

Short out the SELF points and then turn the power

2 short Beeps, the light flashes from red

to green

User Wired Clone Mode

Disconnect the SELF points, turn on the power

while holding down Function Key, press Function

Key again

1 short Beep

Factory Wired Clone

Mode

Short out the SELF points, turn on the power while

holding down Function Key, press Function Key

again

2 short Beeps

Manual Adjust Mode

Enable Manual Adjust Mode, turn on the power

while holding down [PTT] and Function Key

simultaneously, the radio enters this mode in 2

seconds

2 short Beeps, orange light glows

PC Programming &

Adjust Mode

Connect the radio with PC, turn on the radio and

activate this mode in programming software

1. User Mode

User Mode is for conventional communication operation. Disconnect the two SELF points and then turn

the power on, the radio enters User Mode. (Refer to ―TC-600 Owner’s Manual‖for detailed operation

description.)

2. Model Set Mode

(1) Select MS1 according to the radio model. If MS1 is 1, short out the two MS1 points on PCB. If not,

disconnect the two MS1 points.

(2) Short out the two SELF points and then turn the power on. Two Beeps sound.

(3) Turn Channel Selector Knob to the corresponding position (1-11) according to the radio model

(Refer to ―Initial Data Table‖).

(4) Press [PTT] while holding down Function Key to set the model. Channel data and settings are

initialized (Refer to ―Initial Data Table‖).

TC-600 Software Specification

－7 －

(5) Turn off the power and then disconnect the two SELF points to complete the model setting.

For example, MS1 of TC-600U (450.000~469.995MHz) is 0 and its model is 7(Refer to ―Initial

Data Table‖). To initialize its model and channel data, you can operate as following:

●Disconnect the two MS1 points.

●Short out the two SELF points.

●Turn on the power and rotate the Channel Selector Knob to CH7.

●Press [PTT] while holding down Function Key.

●After reset, turn off the power and disconnect the two SELF points. The radio operates at the

preset frequency after restart.

Note: Once the new model is set, previous channel settings (frequency, CTCSS/CDCSS, channel

function settings) will be deleted, and part of functions are also changed. Therefore, do not make this

operation unless it’s very necessary, such as changing the EEPROM, etc.

3. PC Programming Mode

The following parameters can be set through programming software:

(1) Receive frequency and transmit frequency

(2) Receive signaling and transmit signaling

(3) Busy channel lockout (BCL)

(4) Time-out timer (TOT)

(5) Squelch level

(6) Battery save

(7) Audio alarm

(8) Monitor mode

(9) Scan mode

(10) Scan revert channel

(11) Priority scan channel

(12) Wideband/narrowband per radio

(13) High/low power

(14) Wideband/narrowband per channel

TC-600 Software Specification

－8 －

4. PC Adjust Mode

The following settings can be adjusted through the programming software:

(1) Low battery alert level

(2) SQL9

(3) SQL3

(4) CTCSS deviation (wide)

(5) CDCSS deviation (wide)

(6) CTCSS deviation (narrow)

(7) CDCSS deviation (narrow)

5. Manual Adjust Mode

If Manual Adjust Mode is enabled, turn on the power while holding down [PTT] and Function Key

simultaneously, the radio enters Manual Adjust Mode in 2 seconds. Choose the adjusting items by

turning the channel selector knob to CH1-CH7; use [PTT] /Function Key to adjust upwards/downwards

(Note: MIC jack shouldn’t be connected with external cable while adjusting), CH1-CH7 are defined as

follows:

(1) Low battery alert level

(2) SQL9

(3) SQL3

(4) CTCSS deviation (wide)

(5) CDCSS deviation (wide)

(6) CTCSS deviation (narrow)

(7) CDCSS deviation (narrow)

TC-600 Software Specification

－9 －

CH12-CH16 are used to adjust transmitter and receiver. Press [PTT] to transmit; release to receive. In

receive mode, short press the Function Key to toggle among high and low power, or long press it to

switch between wideband and narrowband. Three Beeps alternating from high tone to low tone indicate

that the transmit power is switched from high to low; and three beeps alternating from low tone to high

tone indicate that the transmit power is switched from low to high. Two Beeps sound when wideband is

selected and one Beep sounds when narrowband is selected. CH12-ch16 are defined as follows:

(12) Center frequency (the difference between RX and TX frequency is 0.1MHz)

(13) Lowest frequency (the difference between RX and TX frequency is 0.1MHz)

(14) Highest frequency (the difference between RX and TX frequency is –0.075MHz)

(15) Center frequency: transmit DTMF number ―9‖(the difference between RX and TX frequency is

0.1MHz)

(16) Center frequency: transmit with 250.3Hz CTCSS signaling (the difference between RX and TX

frequency is 0.1MHz)

Note:

To enable/disable the Manual Adjust Mode: short out the two SELF points, turn on the power to enter

Model Set Mode, then Manual Adjust Mode is enabled. Press [PTT] to disable. It suggests this mode be

disabled after the adjustment is completed.

6. User/Factory Wired Clone Mode

The only difference between the two modes is that the latter is able to clone the adjustment settings.

Turn on the power while holding down Function key to enter Wired Clone Mode.

a) If the two SELF points are disconnected, press Function key again, the radio starts user wired clone

and red LED flashes; when cloning is completed, red LED goes out.

b) If the two SELF points are short out, press Function key again, the radio starts factory wired clone

and red LED flashes; when cloning is completed, red LED goes out.

TC-600 Software Specification

－10 －

Initial Data Table

MS1

Model

Frequency

(MHz)

1CH (Center)

2CH (Low)

3CH (High)

4CH

5CH

6CH

7CH

8CH

9-16CH

(MHz)

150.000~173.995

+45.050

162.000

162.100

150.000

150.100

173.975

173.900

162.500

162.550

162.600

162.550

162.650

136.000~149.995

+45.050

143.000

143.100

136.000

136.100

149.975

149.900

143.500

143.550

143.600

143.550

143.650

146.000~173.995

+45.050

160.000

160.100

146.000

146.100

173.975

173.900

160.500

160.550

160.600

160.550

160.650

144.000~147.995

+45.050

146.000

146.100

144.000

144.100

147.975

147.900

146.500

146.550

146.600

146.550

146.650

136.000~147.995

+45.050

142.000

142.100

136.000

136.100

147.975

147.900

142.500

142.550

142.600

142.550

142.650

136.000~173.995

+45.050

155.000

155.100

136.000

136.100

173.975

173.900

155.500

155.550

155.600

155.550

155.650

450.000~469.995

-45.050

460.000

460.100

450.000

450.100

469.975

469.900

460.300

460.350

460.400

460.350

460.450

400.000~419.995

-45.050

410.000

410.100

400.000

400.100

419.975

419.900

410.500

410.550

410.600

410.550

410.650

470.000~489.995

-45.050

480.000

480.100

470.000

470.100

489.975

489.900

480.500

480.550

480.600

480.550

480.650

490.000~511.995

-45.050

501.000

501.100

490.000

490.100

511.975

511.900

501.500

501.550

501.600

501.550

501.650

220.000~239.995

-45.050

230.000

230.100

220.000

220.100

239.975

239.900

230.500

230.550

230.600

230.550

230.650

240.000~259.995

-45.050

250.000

250.100

240.000

240.100

259.975

259.900

250.500

250.550

250.600

250.550

250.650

336.000~367.995

-45.050

352.000

352.100

336.000

336.100

367.975

367.900

352.500

352.550

352.600

352.550

352.650

368.000~395.995

-45.050

382.000

382.100

368.000

368.100

395.975

395.900

382.500

382.550

382.600

382.550

382.650

370.000~389.995

-45.050

380.000

380.100

370.000

370.100

389.975

389.900

380.500

380.550

380.600

380.550

380.650

350.000~369.995

-45.050

360.000

360.100

350.000

350.100

369.975

369.900

360.500

360.550

360.600

360.550

360.650

406.000~429.995

-45.050

418.000

418.100

406.000

406.100

429.975

429.900

418.500

418.550

418.600

418.550

418.650

400.000~429.995

-45.050

415.000

415.100

400.000

400.100

429.975

429.900

415.500

415.550

415.600

415.550

415.650

430.000~439.995

-45.050

435.000

435.100

430.000

430.100

439.975

439.900

435.500

435.550

435.600

435.550

435.650

438.000~449.995

-45.050

444.000

444.100

438.000

438.100

449.975

449.900

444.500

444.550

444.600

444.550

444.650

480.000~519.995

-45.050

500.000

500.100

480.000

480.100

519.975

519.900

500.500

500.550

500.600

500.550

500.650

441.000~451.000

-45.050

446.000

446.100

441.000

441.100

450.975

450.900

446.500

446.550

446.600

446.550

446.650

CH QT/DQT

OFF

023

127.3

151.4

Inhaltsverzeichnis

Andere Hytera Radio Handbücher

Hytera

Hytera Jupiter TETRA Bedienungsanleitung

Hytera

Hytera HM65X Bedienungsanleitung

Hytera

Hytera HP60X Bedienungsanleitung

Hytera

Hytera PDC760UXB2 Bedienungsanleitung

Hytera

Hytera HM782 Bedienungsanleitung

Hytera

Hytera HP56 Series Bedienungsanleitung

Hytera

Hytera HM65X Bedienungsanleitung

Hytera

Hytera RRU3800F080 Bedienungsanleitung

Hytera

Hytera MD65X Bedienungsanleitung

Hytera

Hytera PNC 550 Bedienungsanleitung

Hytera

Hytera DMR Bedienungsanleitung

Hytera

Hytera HM652GBTV Bedienungsanleitung

Hytera

Hytera DMR Bedienungsanleitung

Hytera

Hytera PD562 Bedienungsanleitung

Hytera

Hytera HM78X Bedienungsanleitung

Hytera

Hytera PD78X Series Installations- und Betriebshandbuch

Hytera

Hytera TC-500 Bedienungsanleitung

Hytera

Hytera TC-320 Bedienungsanleitung

Hytera

Hytera PD3 Series Installations- und Betriebshandbuch

Hytera

Hytera MD65X Bedienungsanleitung

Hytera

Hytera MD78X Bedienungsanleitung

Hytera

Hytera MT680 Bedienungsanleitung

Hytera

Hytera MD782 Bedienungsanleitung

Hytera

Hytera PD752i Bedienungsanleitung

Beliebte Radio Handbücher anderer Marken

EisSound

EisSound KBSound iSelect Bedienungsanleitung

Midland

Midland 1001LWX Bedienungsanleitung

Konig

Konig HAV-SR41 Bedienungsanleitung

Roberts

Roberts exprssion Bedienungsanleitung

VDigi

VDigi DD3.0 Bedienungsanleitung

Radio Shack

Radio Shack 21-1863 Bedienungsanleitung

Roberts

Roberts Stream 207 Bedienungsanleitung

Sony

Sony Walkman SRF-M97 Bedienungsanleitung

Stanley

Stanley FatMax FMC770 Bedienungsanleitung

auna

auna DAB-Radio 10026947 Bedienungsanleitung

SOUNDMASTER

SOUNDMASTER UR190 Bedienungsanleitung

HYT

HYT TC-320 Bedienungsanleitung

auna multimedia

auna multimedia Yellowstone 10026851 Bedienungsanleitung

B-Tech

B-Tech GMRS-V2 Bedienungsanleitung

Weierwei

Weierwei VEV-V8 Bedienungsanleitung

SOUNDMASTER

SOUNDMASTER DAB750 Bedienungsanleitung

Telefunken

Telefunken TF-1505 Bedienungsanleitung

Makita

Makita LXRM03 Bedienungsanleitung