Hytronik HBIR29/SV/RH Kurzanleitung
1. Technical Specifications
Installation and Instruction Manual
3. Installation
Mechanical Structure & Dimensions
HBIR29/SV/RH
PIR Standalone Motion Sensor with Mesh
One DALI Channel Output
Subject to change without notice.
Protocol
4 dBm
2.4 GHz - 2.483 GHz
Operation frequency
Transmission power
Range (Typical indoor)
10~30m
Stand-by power
Operating voltage
<
0.65W (Empty load)
220~240VAC 50/60Hz
Switched power
5s
Warming-up
I guaranteed:44mA
I max: 80mA
Certification CE
360
O
Ta:-20
OC~+50OC
PIR detection
Sensor principle
Detection angle
Operation temperature
IP20IP rating
Mesh
EN300328, EN301489-1,
EN301489-17, EN62479,
EN55015, EN61547,
EN60669-1, EN60669-2-1,
EN62493
Standard compliance
Detection range (Max.)*
HBIR29/SV/RH
Installation height：20m (forklift)
12m (person)
Detection range (Ø)：40m
2. Download the App
APP Store
Download on the
The access to Silvair apps
mobile app: Silvair on the App Store
web app: platform.silvair.com
HBIR29/SV/RH-20230831-A0
1. Ceiling (drill hole φ66~68mm)
2. Carefully prise off the cable clamps.
3. Make connections to the pluggable terminal blocks.
4. Insert plug connectors and secure using the provided cable clamps, then clip
terminal covers to the base.
5. Fit detection blind (if required) and desired lens.
6. Clip fascia to body.
7. Bend back springs and insert into ceiling.
* Install lens as required
5
* Install blind as required
A B
7
6
4
2
3
1
Ø 66~68mm
Subject to change without notice.
Wiring Diagram
220~240VAC
DA DA
DA DA
NL
L N
LED
LED Driver
– +
L
N
The device HBIR29/SV/RH can be reset by placing a strong magnet (e.g. N38 neodymium magnet, d=10mm*h=4mm) near the sensor lens for 5 seconds. Once the factory reset is done successfully, the luminaire
flashes and then permanent on, then the device is being able to be re-commissioned by SILVAIR app.
4.Mesh Factory Reset
HBIR29/SV/RH Provisioned
MESH package received 30ms ON
30ms ON
HBIR29/SV/RH Unprovisioned
Factory reset
15ms ON
Status LED blinking Sequence
100ms ON
Factory reset (initial burst)
500ms ONAttention (from network)
300ms OFF
2,000ms OFF
500ms ON 1,000ms OFF
1,000ms OFF
50ms OFF
500ms OFF
5.To Reprovision
Place a strong magnet on the site of the Reset/Hall effect sensor (see diagram 4 below). To trigger the reset the magnet must be held in position for 5 seconds.
Diagram Status LED
Flashes rapidly when unprovisioned.
Flashes slowly when provisioned
Module/Antenna placement
Note: When change the lens part of HBIR29/SV/RH, please kindly make sure that the lens fits the right location,
where the “Reset dot” and “BLE dot”matches with the physical location on the PCB.
Reset zone
Magnet to be replaced
for reprovisioning
Wire Preparation
Pluggable screw terminal. It is recommended to make
connections to the terminal before fitting to the sensor.
0.75 - 2.5mm
7-8mm
HBIR29/SV/RH-20230831-A0
1. 200 metres (total) max. for 1mm² CSA (Ta = 50℃)
2. 300 metres (total) max. for 1.5mm² CSA (Ta = 50℃)
HBIR29/SV/RH-20230831-A0
Subject to change without notice.
Big silicon water-proof gasket dimension(size:mm)
4.2
48.2
61.8
15.2
Small silicon water-proof gasket dimension(size:mm)
Ø 76.5
Ø 62
1.5
4
Big and small silicon gasket used to make IP54 degree protection when HBIR29/SV/RH series device mounted into HA03 housing for ceiling mount
Placement Guide and Typical Range
Smart Phone to Device Range
6-10m ＞10m
The smart device with the App installed will have a typical range
of 10m, but varies from device to device. During commissioning,
the installer will need to be in range of the devices when searching
for devices to add to the network.
Once the devices have been added to the network via the App,
the devices will start communicating within the wireless mesh.
This means that once the network is complete, all devices are
accessible from the smart device when in a 20m range of a
single point.
HBIR29/SV/RH-20230831-A0
Subject to change without notice.
6. Detection Pattern & Optional Accessories
7. Additional Information / Documents
1.Regarding precautions for PIR Sensors installation and operation, please kindly refer to www.hytronik.com/download ->knowledge ->PIR Sensors - Precautions for Product Installation and Operation
2.Data sheet is subject to change without notice. Please always refer to the most recent release on www.hytronik.com/products/bluetooth technology ->Partnership
3.Regarding Hytronik standard guarantee policy, please refer to www.hytronik.com/download ->knowledge ->Hytronik Standard Guarantee Policy
Radial (B)
Tangential (A)
10m
Mount height
14m
15m
13m
12m
11m
max 907m
2
(Ø = 34m)
max 962m
2
(Ø = 35m)
max 1075m
2
(Ø = 37m)
max 660m
2
(Ø = 29m)
max 346m
2
(Ø = 21m)
max 1256m
2
(Ø = 40m)
max 154m
2
(Ø = 14m)
max 177m
2
(Ø = 15m)
max 177m
2
(Ø = 15m)
max 154m
2
(Ø = 14m)
max 113m
2
(Ø = 12m)
max 113m
2
(Ø = 12m)
HBIR29/SV/RH: Reinforced high-bay lens detection pattern for forklift @ Ta = 20ºC
(Recommended ceiling mount installation height 10m-15m)
HBIR29/SV/RH (Reinforced High-bay with 3-Pyro)
A: Tangential movement
Tangential: max. 40m
h = max.20m
A
insensitive sensitive
B: Radial movement
Radial: max. 15m
h = max.20m
B
insensitive sensitive
Tangential: max. 30m
h = max.12m
A
Radial: max. 4m
h = max.12m
B
Radial (B)
Tangential (A)
2.5m
Mount height
11m
12m
10m
8m
6m max 154m
2
(Ø = 14m)
max 38m
2
(Ø = 7m)
max 314m
2
(Ø = 20m)
max 531m
2
(Ø = 26m)
max 615m
2
(Ø = 28m)
max 707m
2
(Ø = 30m)
max 7m
2
(Ø = 3m)
max 7m
2
(Ø = 3m)
max 7m
2
(Ø = 3m)
max 13m
2
(Ø = 4m)
max 13m
2
(Ø = 4m)
max 13m
2
(Ø = 4m)
A: Tangential movement B: Radial movement
HBIR29/SV/RH: Reinforced high-bay lens detection pattern for single person @ Ta = 20OC
(Recommended ceiling mount installation height 2.5m-12m)
insensitive sensitive insensitive sensitive
Optional Accessory --- Ceiling/Surface Mount Box: HA03
Ø 94
20m max 707m2 (Ø = 30m) max 113m2 (Ø = 12m)
4.2
48.2
61.8
75
Andere Hytronik Sicherheitssensor Handbücher
Hytronik
Hytronik Dual Sense HIM31 Bedienungsanleitung
Hytronik
Hytronik HMW15 Kurzanleitung
Hytronik
Hytronik Dual Sense HIM14 Bedienungsanleitung
Hytronik
Hytronik HIM38/RF Kurzanleitung
Hytronik
Hytronik HMW28/PRO Bedienungsanleitung
Hytronik
Hytronik HIR24 Bedienungsanleitung
Hytronik
Hytronik Dual Sense HIM17 Bedienungsanleitung
Hytronik
Hytronik HMW25 Bedienungsanleitung
Hytronik
Hytronik HIR21 Bedienungsanleitung
Hytronik
Hytronik HIM54 Bedienungsanleitung
Hytronik
Hytronik HMW22 Bedienungsanleitung
Hytronik
Hytronik HC403VRC-KD Kurzanleitung
Hytronik
Hytronik HBHC25 Kurzanleitung
Hytronik
Hytronik HIR23 Bedienungsanleitung
Hytronik
Hytronik HIR22 Bedienungsanleitung
Hytronik
Hytronik HBIR29/SV Kurzanleitung
Hytronik
Hytronik HIR21 Bedienungsanleitung
Hytronik
Hytronik HIR28 Kurzanleitung
Hytronik
Hytronik HIM84 Kurzanleitung
Hytronik
Hytronik HC038V Bedienungsanleitung
