i3TOUCH Excellence Bedienungsanleitung
i3TOUCH Excellence
Monitor User Guide
Version 3.6.3
3.6.3 - V3 (15/6)
i3TOUCH EXCELLENCE Monitor User Guide
2
1. Introduction
2. Connecting the Monitor
3. Using the Monitor
4. Cleaning the screen of LCD Monitor
5. Disclaimer
6. Troubleshooting
7. Supplement
8. Touch conguration
8.1 Driver download
8.2 Connecting the touch sensor
8.3 Installing the drivers
8.4 What to check when drivers can’t be installed
8.5 Power supply
8.6 USB-cabling of the i3TOUCH
8.7 Connecting the display (VGA/HDMI/DVI/DP)
8.8 Calibrating the I3TOUCH
8.9 What to do if calibration is still inaccurate even after calibrating in V-sense & windows
8.10 What to do if windows calibration does not start
8.11 Disabling “USB Selective suspend setting”
8.12 No touch after installing the driver
8.13 What to do if you can’t duplicate your screen
3
IMPORTANT SAFETY INSTRUCTIONS
1. Please read these instructions carefully before using the product and keep it for later reference.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Clean the product with a damp soft cloth. Do not use
liquid or aerosol cleaners as it may cause permanent damage to the screen.
4. Caution of use varies from model to model; please observe appropriate operation per model in use.
5. Do not place this product on an unstable cart, stand, or surface which may cause damage or harm to the product or
personnel.
6. Slots and openings on the cabinet, in the back cover or in the bottom, are for ventilation; to ensure reliable
operation and to prevent from overheating; these openings must not be blocked or covered at all time. The openings
should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation
space (min. 2 inches/ 5cm of gap) is provided.
7. This product should receive the type of power indicated on the marking label. If you are not sure of the type of pow-
er available, consult your dealer or local service company.
8. This product is equipped with a 3-wire grounding type power plug, a plug having a third (grounding) pin. This plug
will only t into a grounding-type power outlet. This is a safety feature. If you do not have proper outlet to insert the
plug, contact your electrician to replace your obsolete outlet. Do not break the ground pin and remove the grounding.
9. Do not allow anything to rest, or persons to walk, on the power cord..
10. If an extension cord is used with this product, make sure that the total ampere rating plugged into the extension
cord does not exceed the maximum ampere rating of the extension cord.
11. Never thrust object/tool of any kind through cabinet slots of this product, as they may touch dangerous voltage
point or short out parts that could result in risk of re or electric shock. Never spill liquid of any kind on the product
(except IP-rated models).
12. Do not attempt to service this product yourself; always refer to qualied or authorized personnel for servicing this
product.
13. Unplug this product from the wall outlet and refer servicing to qualied service personnel under the following
conditions:
•When the power cord or plug is damaged or frayed or broken.
•In case that liquid has been spilled into the product (excepting IP-rate models). In case the product does not operate
normally when the operating instructions are followed, adjust only those controls that are delineated by the operating
instructions.
14. Caution: When xed patterns are displayed for a long time, remnant image (retention) is likely to occur.
User/owner of this product is advised to keep all packaging material for use in case for
repackaging the unit for further transportation, or for repair service which
demands returned unit to be properly packed in original packaging as well as proof of purchase
and other required documents per each warranty prescribed.
i3TOUCH EXCELLENCE Monitor User Guide
4
1. Introduction
1-1 About the Product
The monitor consists of a (LED/ TFT) LCD panel and microprocessor -controlled main board. It is designed to meet the de-
manding or rigid performance requirements of education/schools, public premises, corporate, and industrial applications.
GENERAL FUNCTION
• Display type: TFT-LCD MODULE DRIVE BOARD
• RESOLUTION: UP TO 1920X1080 with a 16:9 ASPECT RATIO @60Hz
• AUDIO/ VIDEO SIGNAL CONNECTIONS
• SOURCE INPUT:
o HDMI 1
o HDMI 2
o HDMI 3
o VGA
•SOURCE OUTPUT:
o VGA (sometimes called “Pass Through”or”Loop Through”)
o HDMI (For HDMI 1, HDMI 2 and HDMI 3)
•AUDIO INPUT:
o For VGA audio input.
•AUDIO OUTPUT:
o Audio output follow source.
•DATA CONNECTIONS
USB A1 (A type)/ USB player, support formats listed in section 3-5-2
USB A2 (A type)/ USB Player, support formats listed in section 3-5-2
USB B1 (B type)/ only for connection touch control data to a user PC
USB B2 (B type)/ only for connection touch control data to a user PC
RS232 CONTROL input
•AMBIENT LIGHT DETECT: to see detail in section 3-4(Option: Light Sensor)
• FREEZE: Freeze current picture on screen. (Freeze works with under source VGA/ HDMI. Under source USB1/ USB2, please
press on handheld remote control to pause the picture)
•Aspect Ratio
1-2 Notice
1. Do not apply any sharp object on the original LCD panel surface, if model is
without protective glass.
2. Do not use corrosive or abrasive detergents, waxes or solvents for cleaning.
Use only a dry or damp with clean water, soft cloth when cleaning.
3. Use qualied and safety-approved AC power cord only.
4. Make sure there are no objects all around the i3TOUCH touch sensor area
(left/right or top/bottom) that could inuence the sensor or cause light reection.
5
1-3 Check List
When opening the carton, please make sure that all the items listed below are present:
1. VGA cable (male-to-male) ×1
2. Power cord ×1
3. USB cable ×1 (for touch monitor models only)
4. HDMI cable x1
5. Audio cable 3.5E x1
6. User guide ×1
7. Remote control x 1
8. Battery x2
9. Cleaning fabric x2
10. Stylus x2
11. Wall mount installation guide x1
12. Screw M8*20mm & spring washers x 4
13. Cable Clip x1
If any items are missing or damaged, please contact your local dealer immediately.
Following items are optional at specic ordering:
14. VGA cable (male-to-male) (optional) for VGA out application
Adapter/Converter Advisory Should specic adapter/converter is required, i.e. tablet PCs, in
order to connect to this monitor, please use original adapter/converter recommended by the
original brand. Should A specic adapter/converter BE required.
The length of cables should not be longer than 2 meters each.
i3TOUCH EXCELLENCE Monitor User Guide
6
2. Connecting the Monitor
The procedure for setting up your Monitor kit is as followed:
2-1 Power & Signal Connections
2-1. Power cord connection:
Connect the power cord to the AC outlet.
2-2. Power on:
Switch on the main power of your monitor (switch is located next to the AC outlet)
2-3. Input Source VGA (HDMI1/ HDMI2/ HDMI3) Signal cable connection:
Plug one end of the 15-pin signal cable to the video signal connector at the rear of the PC/laptop system (or engine box) and
the other end to the monitor. Or plug one end of the HDMI signal cable to signal source (PC, laptop, IPC, media player of any
kind with proper HDMI or other out port), and the other end to the HDMI connector on the monitor.
Tighten the connector screws on both ends of the cable to secure good signal connection.
2-4. VGA/ HDMI output connection (Optional male to male VGA/ HDMI cable):
Plug one end of the VGA/ HDMI signal cable to signal source and the other end to another VGA/ HDMI in connector to dai-
sy-chain, of cascading, signal to the other monitor.
Tighten the connector screws on both ends of the cable to secure good signal connection.
2-5. USB cable connection (for touch monitor models):
Plug one end of the USB (B type) cable to the USB (A type) connector at the rear of the (PC, or, IPC, or, media player), and the
other end to the USB connector on monitor.
There are two USB (B type) connecters, one for dynamic source (VGA/ HDMI1/ HDMI2) on rear, the other for HDMI3 on side.
Please connect the signal source rst, then follow by connecting USB cable for touch.
For Operating Systems other than Windows 7 or Windows 8, drivers are required. Please download the latest
drivers at www.i3-technologies.com
7
3. Using the Monitor
3-1 Get to know the monitor
The Monitor connectors are located on the rear side. They are shown in the physical monitor as gure below and described
in the following paragraphs. Please note that connectors may vary in some derivative models; please refer to individual leaf-
let for special notation.
3-2 Connector ports
The Figure below depicts the signal connectors on the main board.
Rear
Side (EZ connect)
i3TOUCH EXCELLENCE Monitor User Guide
8
3.3 Controls: Keypad & remote
3.3.1 keypad
Note: Left = Enter/Select -> under source USB1 or USB2, this key is dened as Select
3.3.2 Remote control
The outlook of remote control is shown in the Figure, hereafter,
Size: 197.2 x 47.1 x 23.2mm (7.7 x 1.85 x 0.9 x in.)
Operation distance: > 10 meter (32ft.)
Working angle: not more then +/- 40 degree
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION
9
3-4 Understanding the OSD Menu (with Remote control)
a. Power
Press the power button to turn on/o the monitor and IPC (If IPC is build-in with monitor).
b. HDMI 1
Press this button to select the HDMI 1signal source.
c. HDMI 2
Press this button to select the HDMI 2signal source.
d. HDMI 3
Press this button to select the HDMI 3signal source.
e. Touch
Press the Touch to turn ON/OFF Touch function
f. VGA
Press this button to select the VGA signal source. Source default is at VGA source.
g. Picture
Press the Picture to select Zoom mode.
h. USB 1
Press this button to select the USB 1 signal source.
i. USB 2
Press this button to select the USB 2 signal source.
j. Vol.+/ Vol.-
Press Vol.+/ Vol- to adjust Volume UP/ DOWN.
k. Mute
Press this button to mute or un-mute.
l. Misc.
Reserved
m. Freeze
Press this button to Freeze picture on screen.
i3TOUCH EXCELLENCE Monitor User Guide
10
n. Auto
Press this button to auto-adjust and optimize picture screen of the monitor.
o. Select function for adjustment
Press the (▲/▼/Enter) button to scroll up and down the intended function items for adjustment, and then press the Enter
button to activate that function item.
p. Menu
Press the Menu button to go into OSD menu.
q. Exit
Press Exit button to exit setting, or, exit OSD menu.
Alternatively, press “Menu” button to exit the OSD Menu instantly at any time.
r. Info
Press to show timing and resolution
s. USB Function
Press to control USB function.
Andere Handbücher für Excellence
3
Inhaltsverzeichnis
Andere i3TOUCH Monitor Handbücher
