IBM 3745 Series Bedienungsanleitung

ÉÂÔ 3745 Communication Controller Models A

3746 Expansion Unit Model 900

3746 Nways Multiprotocol Controller Model 950

Service Processor

Installation and Maintenance

(Based on 6275)

Addendum

EC F70099

SY33-2125-01

These revised pages are intended to replace the equivalent pages in the current version of the

Service

Processor Installation and Maintenance (Based on 6275)

, SY33-2125-01. The pages affected are

pages: 1-25, 1-26, 5-17 and 5-18.

ii 3745-XXA ii 3746-9X0: 6275 SPIM

Step 12. ____ Connect the 25-pin V.24 cable from the DTE to the 25-pin

connector on the modem rear panel. Fasten the connector retaining

screws.

Step 13. ____ Set the modem power switch to ON. Wait until the modem

operational message is displayed on the operator panel (about 15

seconds).

If the modem is connected to an asynchronous DTE which can send AT

commands to the modem, you can use the DTE to configure the modem

to match your communication system requirements. Otherwise, the

modem can be configured through the operator panel, refer to “Setting

the 7858 Connected to the COM1 Connector (ASYN)”

Note: Ten factory Redefined modem configurations are available. You

could retrieve the factory configuration which better matches your system

requirements, make any further configuration adjustment you should

require, and save your modem configuration in one of the ten user

configuration slots.

Step 14. ____ Now the modem is ready for operation. You can try it with your

system. If you observe a basic system problem, such as the DTE not

being able to send commands to the modem successfully, verify again

that your individual modem configuration parameters are matching your

system requirements.

If you have a problem because the dialing tone is not provided by

your PBX or exchange set the modem as follow:

¹Power OFF the modem

¹Power ON the modem while you are pushing the Enter key at the

same time. Release the Enter key when the message: DATAPUMP

TEST is displayed.

After this, the modem performs the dial through the switchboard without

looking for dial tone (Blind dial ATX1). Thios setting is maintained even if

the modem is powered OFF and ON again.

Step 15. ____If you have a problem while using the modem, see "Problem

Determination" chapter in the

IBM 7858 Professional Modem Guide to

Operation

, GA13-1981.

Setting the 7858 Connected to the COM1 Connector (ASYN)

1. ____ Power OFF the modem

2. ____ Press and hold the ↑ key while power ON the modem.

3. ____ The modem is set to Factory 0 in AT command mode.

Saving the Configuration of the 7858

If you want to save the configuration just defined, in order to have it loaded again at

the next modem reset, perform the following steps:

1. ____ Press the ↓ key until the "CONFIGURATIONS" message

displayed the top row.

2. ____ Press the → key until the "Store User Conf."

message displayed the bottom row.

3. ____ Press the ENTER key select the option.

Chapter 1. Installing and Setting Up Your Service Processor 1-25

4. ____ Pressing the ↑ key, select the User Configuration Location where the

current modem configuration must be saved (0 to 9).

5. ____ Press the ENTER key save the current modem configuration.

6. ____ The defined configuration now active and saved.

Now every time the modem is reset (power on), the last user configuration which

was saved is loaded as the current modem configuration.

Connecting the 7858

1. ____ Plug the cable (PN 782984) into slot 3 .1/ of the Service Processor. The

drawer and slide kit (PN 58G5698) are always shipped, but are not used if the

expansion frame is not installed.

2. ____ On the modem's rear panel, plug the other cable lead into the 25-pin

connector .2/.

132

Figure 1-23. Connecting the Service Processor (6275) from COM1 to the 7858

If you received a controller expansion, go to step 3 , otherwise go to “Step 5

- Customizing Your Service Processor” on page 1-33.

3. ____ Slide the 7858 in the controller expansion as shown in Figure 1-24.

Figure 1-24. Installing the 7858 in the Controller Expansion

Go to “Step 5 - Customizing Your Service Processor” on page 1-33 .

1-26 3745-XXA 1-26 3746-9X0: 6275 SPIM

 

Change Configuration Parameters

Adapters Mode | Plug and Play | Other Parameters

Select each mode for a detailed description

Adapter Modes

- Enhanced Modes

- Auto 16 Mode

- ISA 16 Mode

OK Cancel Help





8. Using the Up and Down keys select the ISA 16 Mode ( note that the response

time is very slow) then press simultaneously Alt and P keys to select the Plug

and Play window.

9. The following window is displayed.

 

Change Configuration Parameters

Adapters Mode | Plug and Play | Other Parameters

Make any Changes to the configuration, then select <OK>

- Plug and Play Automatic Configuration

- Manual (locked) Configuration for Plug and Play systems

- Manual Configuration for no Plug and Play (legacy) systems

OK Cancel Help





10. Select the Manual (locked) Configuration for Plug and Play systems, using

the tab key select Interrupt, and using the arrow key, select interrupt: .7/

11. Press simultaneously the Alt and R keys.

12. The following window is displayed.

 

Change Configuration Parameters

Remote IPL Data Rates

o Enable o 16 Mbps

o Disable o 4 Mbps

Auto Sense Bus Wide

o Enable o 16 Mbps

o Disable o 8 Mbps

OK Cancel Help





13. Using the Up, Down, and Tab keys select:

¹Remote IPL: Disable

Chapter 5. Service Processor FRU / Display Exchange 5-17

¹Data Rates: 16 Mbps

¹Auto Sense: Disable

¹Bus Wide: 16 bits

Select OK and press Enter.

14. The following window is displayed.

 

View Adapter Configuration

Configurable | Hardware

Select <Suggest> or <Change> to make changes to the configuration below

Then press <Store> to store these changes to the adapter.

Mode ISA 16 Adapter Plug and Play Manual (legacy)

Remote IPL: Disabled Interrupt: 7

Data Rate: 16 MBps I/O Address: A20-A23

Auto Sens Disabled ROM Address CA000-CBFFF

Bus Width 16 bits RAM Address C8000-C9FFF

Suggest Change Defaults Store

Done Cancel Help





15. Using the Up and Down keys select the Store, then press Enter.

16. The adapter configuration is stored. Wait until the following window is

displayed.

 

Storing Configuration

The adapter configuration settings that you have chosen are

now stored.

NOTE: Changes made to the adapter do not become effective

until your computer is powered OFF and back ON: A reboot

will not activate the changes.





17. Press Enter.

18. The following window is displayed.

 

View Adapter Configuration

Configurable | Hardware

Select <Suggest> or <Change> to make changes to the configuration below

Then press <Store> to store these changes to the adapter.

Mode ISA 16 Adapter Plug and Play Manual (legacy)

Remote IPL: Disabled Interrupt: 7

Data Rate: 16 MBps I/O Address: A20-A23

Auto Sens Disabled ROM Address CA000-CBFFF

Bus Width 16 bits RAM Address C8000-C9FFF

Suggest Change Defaults Store

Done Cancel Help





19. If not selected, using the Tab key, select Done, then press Enter.

5-18 3745-XXA 5-18 3746-9X0: 6275 SPIM

Andere Handbücher für 3745 Series

Dieses Handbuch passt für folgende Modelle

Andere IBM Computerhardware Handbücher

IBM

IBM 6361 Bedienungsanleitung

IBM

IBM 0367 Bedienungsanleitung

IBM

IBM 7133 D40 Bedienungsanleitung

IBM

IBM Power System POWER7 Series Kurzanleitung

IBM

IBM 1 GB Microdrive Storage Card Bedienungsanleitung

IBM

IBM QLogic 4Gb Fibre Channel Expansion Card Bedienungsanleitung

IBM

IBM 6611 Bedienungsanleitung

IBM

IBM 4331 Bedienungsanleitung

IBM

IBM AS/400e 270 Bedienungsanleitung

IBM

IBM eserver 7210 Handbuch

IBM

IBM Power Systems 8247-42L Bedienungsanleitung

IBM

IBM 7311-D11 Gebrauchs- und Pflegehandbuch

IBM

IBM 4764 Bedienungsanleitung

IBM

IBM BladeCenter Management Module Bedienungsanleitung

IBM

IBM 3290 T Bedienungsanleitung

IBM

IBM AIX HACMP SG24-5131-00 Gebrauchsanweisung

IBM

IBM THINKCENTER 8128 Betriebsanleitung

IBM

IBM iSeries 5075 Gebrauchsanweisung

IBM

IBM Power System 9009-41A Bedienungsanleitung

IBM

IBM WD1003-WA2 Bedienungsanleitung

IBM

IBM eserver Cluster 1350 Montage- und Wartungsanleitung

IBM

IBM 3301690 Bedienungsanleitung

IBM

IBM System x Education M5000 Series Bedienungsanleitung

IBM

IBM EMX0 PCIe3 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung