IBM 9008-22L Bedienungsanleitung

Removing and replacing external

cables

IBM

ii Removing and replacing external cables

Contents

Removing and replacing the external HMC cable in the 9008-22L, 9009-22A, or 9223-22H 1

Preparing the system to remove and replace the external HMC cable ................ 1

Removing the external HMC cable from the 9008-22L, 9009-22A, or 9223-22H ............. 1

Replacing the external HMC cable in the 9008-22L, 9009-22A, or 9223-22H............... 2

Preparing the system for operation after removing and replacing the external HMC cable ......... 2

Removing and replacing the external serial cable in the 9008-22L, 9009-22A, or

9223-22H ................................... 3

Preparing the system to remove and replace the external serial cable ................ 3

Removing the external serial cable from the 9008-22L, 9009-22A, or 9223-22H.............. 3

Replacing the external serial cable in the 9008-22L, 9009-22A, or 9223-22H ............... 4

Preparing the system for operation after removing and replacing the external serial cable ......... 4

Removing and replacing the external USB cable in the 9008-22L, 9009-22A, or 9223-22H 5

Preparing the system to remove and replace the external USB cable ................. 5

Removing the external USB cable from the 9008-22L, 9009-22A, or 9223-22H .............. 5

Replacing the external USB cable in the 9008-22L, 9009-22A, or 9223-22H ............... 6

Preparing the system for operation after removing and replacing the external USB cable .......... 6

iii

iv Removing and replacing external cables

Removing and replacing the external HMC cable in the

9008-22L, 9009-22A, or 9223-22H

Find information about removing and replacing the external HMC cable in the 9008-22L, 9009-22A, or

9223-22H.

Preparing the system to remove and replace the external HMC cable

To prepare the system to remove and replace the external HMC cable, complete the steps in this

procedure.

Procedure

Removing the external HMC cable from the 9008-22L, 9009-22A, or

9223-22H

To remove the external HMC cable, complete the steps in this procedure.

Procedure

1. Attach the electrostatic discharge (ESD) wrist strap. The ESD wrist strap must be connected to an

unpainted metal surface until the service procedure is completed, and if applicable, until the service

access cover is replaced.

Attention:

vAttach an electrostatic discharge (ESD) wrist strap to the front ESD jack, to the rear ESD jack, or to

an unpainted metal surface of your hardware to prevent the electrostatic discharge from damaging

your hardware.

vWhen you use an ESD wrist strap, follow all electrical safety procedures. An ESD wrist strap is

used for static control. It does not increase or decrease your risk of receiving electric shock when

using or working on electrical equipment.

vIf you do not have an ESD wrist strap, just prior to removing the product from ESD packaging and

installing or replacing hardware, touch an unpainted metal surface of the system for a minimum of

5 seconds. If at any point in this service process you move away from the system, it is important to

again discharge yourself by touching an unpainted metal surface for at least 5 seconds before you

continue with the service process.

2. Disconnect the HMC cable indicated in the FRU Location field in the upper left of this page. See

Figure 1.

Figure 1. Removing an HMC cable

Replacing the external HMC cable in the 9008-22L, 9009-22A, or

9223-22H

To replace the external HMC cable, complete the steps in this procedure.

Procedure

1. Ensure that you have the electrostatic discharge (ESD) wrist strap on and that the ESD clip is plugged

into a ground jack or connected to an unpainted metal surface. If not, do so now.

2. Connect the HMC cable indicated in the FRU Location field in the upper left of this page. See

Figure 2.

Preparing the system for operation after removing and replacing the

external HMC cable

To prepare the system for operation after removing and replacing the external HMC cable, complete the

steps in this procedure.

Procedure

Figure 2. Replacing an HMC cable

2Removing and replacing external cables

Removing and replacing the external serial cable in the

9008-22L, 9009-22A, or 9223-22H

Find information about removing and replacing the external serial cable in the 9008-22L, 9009-22A, or

9223-22H.

Preparing the system to remove and replace the external serial cable

To prepare the system to remove and replace the external serial cable, complete the steps in this

procedure.

Procedure

Removing the external serial cable from the 9008-22L, 9009-22A, or

9223-22H

To remove the external serial cable, complete the steps in this procedure.

Procedure

1. Attach the electrostatic discharge (ESD) wrist strap. The ESD wrist strap must be connected to an

unpainted metal surface until the service procedure is completed, and if applicable, until the service

access cover is replaced.

Attention:

vAttach an electrostatic discharge (ESD) wrist strap to the front ESD jack, to the rear ESD jack, or to

an unpainted metal surface of your hardware to prevent the electrostatic discharge from damaging

your hardware.

vWhen you use an ESD wrist strap, follow all electrical safety procedures. An ESD wrist strap is

used for static control. It does not increase or decrease your risk of receiving electric shock when

using or working on electrical equipment.

vIf you do not have an ESD wrist strap, just prior to removing the product from ESD packaging and

installing or replacing hardware, touch an unpainted metal surface of the system for a minimum of

5 seconds. If at any point in this service process you move away from the system, it is important to

again discharge yourself by touching an unpainted metal surface for at least 5 seconds before you

continue with the service process.

2. Disconnect the serial cable indicated in the FRU Location field in the upper left of this page. See

Figure 3.

Figure 3. Removing the serial cable

Replacing the external serial cable in the 9008-22L, 9009-22A, or

9223-22H

To replace the external serial cable, complete the steps in this procedure.

Procedure

1. Ensure that you have the electrostatic discharge (ESD) wrist strap on and that the ESD clip is plugged

into a ground jack or connected to an unpainted metal surface. If not, do so now.

2. Connect the serial cable indicated in the FRU Location field in the upper left of this page. See

Figure 4.

Preparing the system for operation after removing and replacing the

external serial cable

To prepare the system for operation after removing and replacing the external serial cable, complete the

steps in this procedure.

Procedure

Figure 4. Replacing the serial cable

4Removing and replacing external cables

Removing and replacing the external USB cable in the

9008-22L, 9009-22A, or 9223-22H

Find information about removing and replacing the external USB cable in the 9008-22L, 9009-22A, or

9223-22H.

Preparing the system to remove and replace the external USB cable

To prepare the system to remove and replace the external USB cable, complete the steps in this

procedure.

Procedure

Removing the external USB cable from the 9008-22L, 9009-22A, or

9223-22H

To remove the external USB cable, complete the steps in this procedure.

Procedure

1. Attach the electrostatic discharge (ESD) wrist strap. The ESD wrist strap must be connected to an

unpainted metal surface until the service procedure is completed, and if applicable, until the service

access cover is replaced.

Attention:

vAttach an electrostatic discharge (ESD) wrist strap to the front ESD jack, to the rear ESD jack, or to

an unpainted metal surface of your hardware to prevent the electrostatic discharge from damaging

your hardware.

vWhen you use an ESD wrist strap, follow all electrical safety procedures. An ESD wrist strap is

used for static control. It does not increase or decrease your risk of receiving electric shock when

using or working on electrical equipment.

vIf you do not have an ESD wrist strap, just prior to removing the product from ESD packaging and

installing or replacing hardware, touch an unpainted metal surface of the system for a minimum of

5 seconds. If at any point in this service process you move away from the system, it is important to

again discharge yourself by touching an unpainted metal surface for at least 5 seconds before you

continue with the service process.

2. Disconnect the USB cable indicated in the FRU Location field in the upper left of this page. See

Figure 5.

Figure 5. Removing a USB cable

Replacing the external USB cable in the 9008-22L, 9009-22A, or

9223-22H

To replace the external USB cable, complete the steps in this procedure.

Procedure

1. Ensure that you have the electrostatic discharge (ESD) wrist strap on and that the ESD clip is plugged

into a ground jack or connected to an unpainted metal surface. If not, do so now.

2. Connect the USB cable indicated in the FRU Location field in the upper left of this page. See Figure 6.

Preparing the system for operation after removing and replacing the

external USB cable

To prepare the system for operation after removing and replacing the external USB cable, complete the

steps in this procedure.

Procedure

Figure 6. Replacing a USB cable

6Removing and replacing external cables

Andere Handbücher für 9008-22L

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IBM Stromversorgung Handbücher

IBM

IBM Power Systems EMX0 PCIe Gen3 Bedienungsanleitung

IBM

IBM 11000 VA LCD 5U Bedienungsanleitung

IBM

IBM POWER 730 Bedienungsanleitung

IBM

IBM 9006-12C Bedienungsanleitung

IBM

IBM Power System 9009-41A Bedienungsanleitung

IBM

IBM S822LC Benutzerhandbuch

IBM

IBM 170 Servers Bedienungsanleitung

IBM

IBM BladeCenter Management Module Bedienungsanleitung

IBM

IBM 7199-92X Bedienungsanleitung

IBM

IBM SCM Bedienungsanleitung

IBM

IBM S824L Bedienungsanleitung

IBM

IBM 3000VA Bedienungsanleitung

IBM

IBM Power System IC922 Bedienungsanleitung

IBM

IBM 9006-22C Bedienungsanleitung

IBM

IBM Power System 9009-41A Bedienungsanleitung

IBM

IBM Power 720 Express 8202-E4B Bedienungsanleitung

IBM

IBM E850 Bedienungsanleitung

IBM

IBM S922L Bedienungsanleitung

IBM

IBM SAS RAID controllers Bedienungsanleitung

IBM

IBM CS821 Bedienungsanleitung

IBM

IBM 8203-E4A Bedienungsanleitung

IBM

IBM Power System L922 Bedienungsanleitung

IBM

IBM 9117-MMB Bedienungsanleitung

IBM

IBM 5786 Gebrauchs- und Pflegehandbuch

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung