IBM AS/400e 270 Kurzanleitung

AS/400e 270 or 820

Upgrading the System Unit from

Twinaxial Console to Operations

Console (Feature 5544)

Ve r s i o n 4

SENG-5544-00



AS/400e 270 or 820

Upgrading the System Unit from

Twinaxial Console to Operations

Console (Feature 5544)

Ve r s i o n 4

SENG-5544-00



Note

Before using this information and the product it supports, be sure to read the “Safety and Environmental Notices” on

page iii and the “Notices” on page 15.

First Edition (July 2000)

This edition applies only to reduced instructions set computer (RISC) systems.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

Safety and Environmental Notices

Danger Notices

A danger notice calls attention to a situation that is potentially lethal or extremely

hazardous to people.

DANGER

To prevent a possible electrical shock during an electrical storm, do not

connect or disconnect cables or station protectors for communications lines,

display stations, printers, or telephones. (RSFTD003)

DANGER

To prevent a possible electrical shock from touching two surfaces with

different electrical grounds, use one hand, when possible, to connect or

disconnect signal cables. (RSFTD004)

DANGER

An electrical outlet that is not correctly wired could place hazardous voltage

on metal parts of the system or the products that attach to the system. It is the

customer’s responsibility to ensure that the outlet is correctly wired and

grounded to prevent an electrical shock. (RSFTD201)

DANGER

To prevent a possible electrical shock when adding or removing any devices

to or from the system, ensure that the power cords for those devices are

unplugged before the signal cables are connected or disconnected. If possible,

disconnect all power cords from the existing system before you add or

remove a device. (RSFTD203)

Caution Notices

A caution notice calls attention to a situation that is potentially hazardous to

people because of some existing condition.

CAUTION:

Telecommunications Statement: This unit contains over-voltage circuits between

the ac power outlet and the unit. These circuits meet the standard limits

described in International Electrical Commission (IEC) 664, installation category

II. It is the customer’s responsibility to ensure that the power outlet meets the

standards of IEC 664, installation category II. (RSFTC214)

Laser Safety Information

CAUTION:

This product may contain a CD-ROM which is a class 1 laser product.

(RSFTC240)

Product Recycling and Disposal

Components of the system, such as structural parts and circuit cards, can be

recycled where recycling facilities exist. IBM does not currently collect and recycle

used IBM products from customers in the United States other than those products

that are involved in trade-in programs. Companies are available to disassemble,

reutilize, recycle, or dispose of electronic products. Contact an IBM account

representative for more information.

The system unit contains batteries and circuit boards with lead solder. Before you

dispose of this unit, these batteries and circuit boards must be removed and

discarded according to local regulations or recycled where facilities exist. This book

contains specific information on each battery type where applicable.

Battery Return Program

In the United States, IBM has established a collection process for reuse, recycling,

or proper disposal of used IBM batteries and battery packs. For information on

proper disposal of the batteries in this unit, please contact IBM at 1-800-426-4333.

Please have the IBM part number that is listed on the battery available when you

make your call. For information on battery disposal outside the United States,

contact your local waste disposal facility.

Environmental Design

The environmental efforts that have gone into the design of the system signify

IBM’s commitment to improve the quality of its products and processes. Some of

these accomplishments include the elimination of the use of Class I

ozone-depleting chemicals in the manufacturing process, reductions in

manufacturing wastes, and increased product energy efficiency. For more

information, contact an IBM account representative.

iv AS/400e 270 or 820: Upgrading the System Unit from Twinaxial Console to Operations Console (Feature 5544)

Upgrading Twinaxial Console to Operations Console

These instructions contain steps on how to upgrade your Twinaxial Console to an

Operations Console.

If you are going to connect a remote control panel cable, ensure that you have the

cable available before you begin this upgrade.

Install the Operations Console prerequisites on the personal computer (PC). See the

Operations Console Setup, SC41-5508-01, book for prerequisites, located on the

Installation and Service Library CD, SK3T-4028-02.

You are changing the console device, the AS/400 system value QAUTOCFG must

be set to ON. Use the following to verify or set this system value on the AS/400:

__ 1. Enter WRKSYSVAL QAUTOCFG on an OS/400 command line and press

Enter.

__ 2. Select Change option from the Work with System Values display and press

Enter.

__ 3. Select option 1=ON from the Change System Value display and press Enter.

__ 4. The Work with System Values display appears. Press F3 once to return to

tthe AS/400 Main Menu.

Before you begin

This feature is customer-installable. You can elect not to do this installation

yourself. Contact IBM or an Authorized Dealer to make arrangements for them to

perform the feature installation for a fee.

You need to allow additional time to complete your jobs, back up your system,

initial program load (IPL) your system, and verify your hardware configuration.

When you use these instructions, you may do some of the following:

vRemove the system unit covers.

vInstall your new hardware.

vInstall covers.

vIPL your operating system.

vVerify your new hardware configuration.

Some of the pictures in these instructions may not look exactly like the system unit

that you have. However, the steps to perform the task are the same.

__ 1. Ensure that you have a current backup of your system (including operating

systems, licensed programs, and data).

__ 2. Ensure that you take a few minutes to become familiar with these

instructions.

__ 3. If there are incorrect, missing or visibly damaged parts, contact one of the

following:

vYour authorized dealer

vIBM Rochester Manufacturing Automated Information Line (R-MAIL)

–1-800-300-8751 (United States)

–1-507-253-5242 (worldwide)

__ 4. If you encounter difficulties during the installation, contact your authorized

service provider or your authorized dealer.

__ 5. Determine if there are any existing prerequisites before you install your new

feature. Go to this Web site and locate your feature number and OS/400

release and check the prerequisites.

http://as400service.ibm.com/s_dir/slkbase.NSF/

Then do the following to get to the Customer Install Features Prerequisites:

a. Select All Documents

b. Select Collapse

c. Select General Information

d. Select Offerings

e. Select Feature Prerequisites

f. Select Customer Install Features Prerequisites

Powering off the system unit

__ 1. Ensure that all jobs are complete.

__ 2. When all jobs are complete, type pwrdwnsys *immed on an AS/400 command

line and press Enter.

__ 3. Is your system unit an AS/400e 270 or 820?

270 820

↓Go to step 6 on page 3.

__ 4. Look at the Function/Data display on the control panel. Refer to “System

unit control panel”on page 9.

__ 5. Does 01 B N V=S appear in the Function/Data display?

No Yes

↓Do the following:

__ a. Press the Increment/Decrement push button until 02 appears

in the Function/Data display.

__ b. Press the Enter push button on the control panel.

__ c. Press the Increment/Decrement push button until Bappears

in the Function/Data display.

__ d. Press the Enter push button on the control panel.

__ e. Press the Increment/Decrement push button until Mappears

in the Function/Data display.

__ f. Press the Enter push button on the control panel.

__ g. Press the Increment/Decrement push button until Sappears

in the Function/Data display.

__ h. Press the Enter push button on the control panel.

__ i. Press the Increment/Decrement push button until 01 appears

in the Function/Data display.

__ j. Press the Enter push button on the control panel.

01BMSshould appear in the Function/Data display. If it

does not, repeat steps 5a through 5j.

__ k. Go to step 8 on page 3.

2AS/400e 270 or 820: Upgrading the System Unit from Twinaxial Console to Operations Console (Feature 5544)

Go to step 8.

__ 6. Look at the Function/Data display on the control panel.

__ 7. Does 01 B V=S appear in the Function/Data display and the Manual mode

indicator (a small hand) lit?

Yes No

↓Do the following:

__ a. Press the Mode Select button until the Manual mode

indicator (a small hand) lights up.

__ b. Press the Increment/Decrement push button until 02 appears

in the Function/Data display.

__ c. Press the Enter push button on the control panel.

__ d. Press the Increment/Decrement push button until Bappears

in the Function/Data display.

__ e. Press the Enter push button on the control panel.

__ f. Press the Increment/Decrement push button until Sappears

in the Function/Data display

__ g. Press the Enter push button on the control panel.

__ h. Press the Increment/Decrement push button until 01 appears

in the Function/Data display.

__ i. Press the Enter push button on the control panel.

01BSshould appear in the Function/Display panel. If it

does not appear, repeat steps 7a through 7h.

__ 8. Press the Power push button that is located on the AS/400 control panel.

There is approximately a 10 second delay before the power-on light comes

on, and data appears in the Function/Data display.

Note: The system takes approximately 5 to 10 minutes to power on and

complete an IPL. When the IPL is complete, the IPL or Install the

System display should appear on your system unit console.

Selecting AS/400 Operations Console as the console device

Use this section to select AS/400 Operations Console as the console device for your

dial-up LCS. When the IPL or Install the System display appears:

__ 1. Select Use Dedicated Service Tools (DST) and press Enter.

__ 2. Type QSECOFR for the DST user and the DST password on the Dedicated

Service Tools (DST) Sign On display and press Enter.

__ 3. Select Work with DST environment from the Use Dedicated Service Tools

(DST) display and press Enter.

__ 4. Select System devices from the Work with DST Environment display and

press Enter.

__ 5. Select Console mode from the Work with System Devices display and press

Enter.

__ 6. Select Operations Console from the Select Console Type display and press

Enter.

Important: Make sure that you type 2 and press Enter even if 2 already

exists. This forces a rewrite of the value.

__ 7. Press the F3 key until you return to the Use Dedicated Service Tools (DST)

display.

Upgrading Twinaxial Console to Operations Console 3

__ 8. Select Start a service tool and press Enter.

__ 9. Select Operator panel functions and press Enter.

__ 10. Select the function key to power off the system (F10).

__ 11. Press Enter to confirm that you want to power down.

__ 12. Power off and unplug attached workstations and printers.

Connecting the Operations Console cable

__ 1. Remove the system unit back cover.

__ a. Place your hand near the bottom of the back cover and lift up and

out.

__ b. Attention: If removing side cover while powered on, errors may

occur due to electromagnetic interference.

__ 2. Attach the disposable wrist strap to prevent electrostatic discharge from

damaging a device. Attach the adhesive part of the foil to an unpainted

surface.

__ 3. If you have a 270 System Unit, locate position C07. See “PCI card locations”

on page 13 for more information.

__ 4. If you have a 820 System Unit, locate position C06. See “PCI card locations”

on page 13 for more information.

4AS/400e 270 or 820: Upgrading the System Unit from Twinaxial Console to Operations Console (Feature 5544)

Andere Handbücher für AS/400e 270

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IBM Server Handbücher

IBM

IBM eServer xSeries 135 Bedienungsanleitung

IBM

IBM System x3650 M3 4255 Bedienungsanleitung

IBM

IBM 450 xSeries Technisches Handbuch

IBM

IBM Power Systems 9043-MRX Bedienungsanleitung

IBM

IBM S822LC Bedienungsanleitung

IBM

IBM eserver pSeries 7311 D10 Bedienungsanleitung

IBM

IBM 6.00E+04 Bedienungsanleitung

IBM

IBM RS/6000 SP Bedienungsanleitung

IBM

IBM x3400 Bedienungsanleitung

IBM

IBM x3655 - System - 7985 Bedienungsanleitung

IBM

IBM eServer 325 Bedienungsanleitung

IBM

IBM S822LC Bedienungsanleitung

IBM

IBM xSeries 455 Bedienungsanleitung

IBM

IBM Power System LC922 Bedienungsanleitung

IBM

IBM 8668 - Eserver xSeries 232 Betriebsanleitung

IBM

IBM System x3100 M4 Bedienungsanleitung

IBM

IBM System x3500 M4 Bedienungsanleitung

IBM

IBM System x3620 M3 7376 Bedienungsanleitung

IBM

IBM System x3755 M3 7164 Bedienungsanleitung

IBM

IBM eserver pSeries 690 Bedienungsanleitung

IBM

IBM System x3300 M4 Handbuch

IBM

IBM 8677 - BladeCenter Rack-mountable - Power... Bedienungsanleitung

IBM

IBM xSeries 366 Bedienungsanleitung

IBM

IBM Accesser F5100 3401-A02 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung