IBM 10/20 GB TR-5 Bedienungsanleitung

10/20 GB TR-5

IDE Tape Drive

User's Guide

OPTIONS

by IBM

Note: If you are using this product in the United States, Canada, or Puerto Rico, be sure to read the information under Appendix C,

“Product warranty and notices” on page 3-8 before using this information and the product it supports.

For all other countries, the warranty terms and conditions applicable in the country of purchase are available from IBM or your reseller.

First Edition (January 1999)

The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law: INTERNATIONAL

BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be

incorporated in new editions of the publication. IBM may make improvements and/or changes in the product(s) and/or the program(s) described in this publication

at any time.

This publication was developed for products and services offered in the United States of America. IBM may not offer the products, services, or features discussed

in this document in other countries, and the information is subject to change without notice. Consult your local IBM representative for information on the

products, services, and features available in your area.

Requests for technical information about IBM products should be made to your IBM reseller or IBM marketing representative.

Note to U.S. Government Users — Documentation related to restricted rights — Use, duplication or disclosure is subject to restrictions set forth in GSA ADP

Schedule Contract with IBM Corp.

Contents

Registering your option .................... iv

About this book ........................ iv

Part 1: Quick Installation Guide ................................................ 1-1

Part 2: User's Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Product description . . . . . . . . . . . . . . . . . . . . . . 2-1

Before you begin ....................... 2-3

Installing the Enhanced IDE drive .............. 2-3

Installing the software .................... 2-7

Using the tape drive ..................... 2-8

Loading and unloading tape cartridges ............. 2-8

Setting the write-protect switch ................ 2-9

Reviewing performance considerations ............. 2-9

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Caring for tape cartridges .................. 2-10

Cleaning the tape head .................... 2-10

Part 3: Appendixes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Appendix A. 10/20 GB TR-5 IDE Tape Drive specifications 3-1

Appendix B. Help and service information ......... 3-6

Step 1: Troubleshooting . . . . . . . . . . . . . . . . . . . . 3-6

Step 2: Preparing for the call ................. 3-7

Step 3: Placing the call to IBM ................ 3-7

Appendix C. Product warranty and notices ......... 3-8

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Electronic emission notices ................. 3-11

Registering your option

Thank you for purchasing OPTIONS by IBM. Please take a few

moments to register your product and provide us with information that

will help IBM to better serve you in the future. Your feedback is

valuable to us in developing products and services that are important

to you, as well as in developing better ways to communicate with you.

http://www.pc.ibm.com/register

IBM will send you information and updates on your registered product

unless you indicate on the Web site questionnaire that you do not want

to receive further information.

You can obtain more tips and updates for your option by typing “10

20” in the Search query box at:

http://www.pc.ibm.com/support

About this book

This manual contains information on the 10/20 GB TR-5 IDE Tape

Drive. It is divided into the following parts:

Part 1: Quick installation instructions, in the following languages:

English

German

French

Spanish

Italian

Brazilian Portuguese

Japanese

Part 2: Product description, with detailed installation and usage

instructions

Part 3: Product specifications, problem solving, help and service

information, warranty, and notices

Note: The illustrations in this publication might be slightly different

from your hardware.

iv 10/20 GB TR-5 IDE Tape Drive User’s Guide

Part 1: Quick Installation Guide

This guide contains installation instructions in an abbreviated form. If

you are knowledgeable about IDE products and experienced in

installing options, use these instructions to quickly install your tape

drive. For a description of the tape drive and more detailed

installation instructions, go to “Part 2: User's Guide” on page 2-1.

In addition to this manual, this option package contains:

Internal model of the tape drive

5.25-inch mounting kit

One Imation or IBM TR-5 formatted data cartridge

Tape software CD

Mounting screws

Various bezels

IDE cable

Safety Information

Contact your place of purchase if any item is missing or damaged.

Important: Be sure to retain your proof of purchase because it might

be required to receive warranty service.

Installing the Enhanced IDE drive

Follow these instructions to install the Enhanced IDE tape drive:

1. Turn off the computer and unplug the power cables from the

power outlet for the computer and all attached peripherals.

2. Open the computer.

3. Touch the static-protective bag containing the tape drive to an

unpainted metal surface on the computer for at least 2 seconds.

Remove the drive from the static-protective bag, holding the drive

by the edges, and place it on the bag.

4. Refer to the bottom view of the tape drive to locate the IDE

configuration block and how to set a position ON (A) or OFF

(B).

The IDE configuration block pin assignments are:

7 and 8: Reserved

5 and 6: MS

3 and 4: SL

1 and 2: CS

5. Set the IDE jumper ON for the setting that applies to your IDE

configuration. The tape drive is preset at the factory to slave

(SL).

If your computer has one hard disk drive and one IDE controller,

configure the tape drive as a slave (SL) by placing a jumper over

vertical pins 3 and 4 (ON). Some hard disk drives might require

you to change its jumper setting (master to master with a slave

attached) if you attach a second device to the IDE controller.

If your computer has two IDE controllers:

Place the hard disk drives on the primary IDE controller and

place the other storage devices (tape drive or CD-ROM

drive) on the secondary IDE controller.

If the tape drive is the only device on the secondary IDE

controller, configure it as a master (MS) by placing a jumper

over vertical pins 5 and 6.

If the tape drive is sharing the IDE controller with another

device, configure it as slave (SL) by placing a jumper over

vertical pins 3 and 4.

Refer to your computer documentation to see if your computer

supports the cable select (CS) setting. Most computers do not

use this feature.

6. Locate an available bay or space in your computer to mount the

tape drive. The drive can be mounted in either a horizontal or

vertical position. The drive fits in a 3.5-inch (1-inch high)

standard bay. You can also mount the drive in a 5.25-inch

(1.6-inch high) bay using the 5.25-inch mounting kit provided.

The installation instructions are located on the mounting kit

packaging.

The following table lists the available bays for IBM PC

IntelliStation professional workstation and desktop PC models.

Some of these computer systems require an additional cosmetic

bezel (included) when installing a removable media device such

as a tape drive. Some workstations also might have a lockable

door covering the drive bays. If you are installing the tape

drive into any server with a lockable door, you might not be

able to close this door whenever the data cartridge is inserted.

Model Bays Available

IntelliStation M Pro both sizes1

IntelliStation Z Pro both sizes1

PC 300 PL 5.25 in. only

PC 300 GL 5.25 in. only

1When installing in the available 3.5-inch bay in the tower model, no additional bezel is available at this time.

1-2 10/20 GB TR-5 IDE Tape Drive User’s Guide

7. Remove the bay cover, if necessary. Slide the tape drive into the

bay, and secure it with the mounting screws provided in the

option package. Do not use any other screws to secure the

drive. Using screws that are too long might damage the drive.

8. Locate the IDE bus cable (usually a 50-pin ribbon cable) that is

inside your computer, and attach one of the connectors on the

cable to the tape drive. Ensure that pin 1 of the cable (usually

color-coded) aligns with pin 1 of the IDE connector on the tape

drive. If your computer system does not have connectors on the

drive, you might need to use the IDE cable included with the

option.

9. Locate an available power cable inside your computer, and

connect it to the four-pin power connector on the tape drive.

10. Replace the computer cover, and secure it in place.

11. Reconnect the ac power cord and any other signal cables to the

outside of your computer, and plug the power cord into an

available power outlet. Turn on all attached devices; then turn on

the computer.

12. Install the software using the instructions given by the README

file on the tape software CD. The CD contains tape backup and

restore applications for most desktop operating systems.

To install the backup software for native Windows NT 4.0

support:

a. From the Windows NT desktop, select Start, Settings,

Control Panel, Tape Device.

b. Windows NT detects a “New SCSI Tape Device” and

prompts you to install the IDE (QIC-157) device driver.

c. Click OK.

d. Insert the Windows NT Workstation CD and click OK.

e. Windows NT will display the location of the needed files,

directory i386, on the CD drive. If the correct drive is not

shown on the “Copy files from:” list, click the down-arrow

button and select the correct CD drive for the computer.

f. Click OK.

g. Windows NT will now complete the device driver

installation.

To verify that the driver is correctly loaded, go to the

desktop and select Start, Settings, Control Panel, Tape

Devices.

h. Start Windows NT Backup by selecting Programs,

Administrative Tools, Backup.

i. The software installation is now completed.

To install the additional Seagate backup software for Windows

98, Windows 95 or Windows NT:

a. Place the Seagate Backup Exec CD in your CD-ROM.

b. If your operating system is configured for autoplay, the setup

program will run automatically. If the setup program does

not run automatically, select Run from the Start menu.

Then type x:\setup, where x is the drive letter for your

CD-ROM, and press Enter.

c. Follow the on-screen instructions.

d. Restart Windows to complete software installation.

Part 1: Quick Installation Guide 1-3

To install the additional Seagate backup software for Windows

3.1:

a. From Program Manager, select File, Run.

b. Type x:\setup, where x is the drive letter for your CD-ROM,

and press Enter.

c. Follow the on-screen instructions.

d. Restart Windows to complete software installation.

1-4 10/20 GB TR-5 IDE Tape Drive User’s Guide

Quick Installation Guide (Translate)

This guide contains installation instructions in an abbreviated form. If

you are knowledgeable about IDE products and experienced in

installing options, use these instructions to quickly install your tape

drive.

In addition to this manual, this option package contains:

Internal model of the tape drive

5.25-inch mounting kit

One Imation or IBM TR-5 formatted data cartridge

Tape software CD

Mounting screws

Various bezels

IDE cable

Safety Information

Contact your place of purchase if any item is missing or damaged.

Important: Be sure to retain your proof of purchase because it might

be required to receive warranty service.

Installing the Enhanced IDE drive

Follow these instructions to install the Enhanced IDE tape drive:

1. Turn off the computer and unplug the power cables from the

power outlet for the computer and all attached peripherals.

2. Open the computer.

3. Touch the static-protective bag containing the tape drive to an

unpainted metal surface on the computer for at least 2 seconds.

Remove the drive from the static-protective bag, holding the drive

by the edges, and place it on the bag.

4. Refer to the bottom view of the tape drive to locate the IDE

configuration block and how to set a position ON (A) or OFF

(B).

Part 1: Quick Installation Guide 1-5

The IDE configuration block pin assignments are:

7 and 8: Reserved

5 and 6: MS

3 and 4: SL

1 and 2: CS

5. Set the IDE jumper ON for the setting that applies to your IDE

configuration. The tape drive is preset at the factory to slave

(SL).

If your computer has one hard disk drive and one IDE controller,

configure the tape drive as a slave (SL) by placing a jumper over

vertical pins 3 and 4 (ON). Some hard disk drives might require

you to change its jumper setting (master to master with a slave

attached) if you attach a second device to the IDE controller.

If your computer has two IDE controllers:

Place the hard disk drives on the primary IDE controller and

place the other storage devices (tape drive or CD-ROM

drive) on the secondary IDE controller.

If the tape drive is the only device on the secondary IDE

controller, configure it as a master (MS) by placing a jumper

over vertical pins 5 and 6.

If the tape drive is sharing the IDE controller with another

device, configure it as slave (SL) by placing a jumper over

vertical pins 3 and 4.

Refer to your computer documentation to see if your computer

supports the cable select (CS) setting. Most computers do not

use this feature.

6. Locate an available bay or space in your computer to mount the

tape drive. The drive can be mounted in either a horizontal or

vertical position. The drive fits in a 3.5-inch (1-inch high)

standard bay. You can also mount the drive in a 5.25-inch

(1.6-inch high) bay using the 5.25-inch mounting kit provided.

The installation instructions are located on the mounting kit

packaging.

The following table lists the available bays for IBM PC

IntelliStation professional workstation and desktop PC models.

Some of these computer systems require an additional cosmetic

bezel (included) when installing a removable media device such

as a tape drive. Some workstations also might have a lockable

door covering the drive bays. If you are installing the tape

drive into any server with a lockable door, you might not be

able to close this door whenever the data cartridge is inserted.

Model Bays Available

IntelliStation M Pro both sizes2

IntelliStation Z Pro both sizes2

PC 300 PL 5.25 in. only

PC 300 GL 5.25 in. only

2When installing in the available 3.5-inch bay in the tower model, no additional bezel is available at this time.

1-6 10/20 GB TR-5 IDE Tape Drive User’s Guide

Andere IBM Lagerung Handbücher

IBM

IBM TotalStorage Ultrium T800 Handbuch

IBM

IBM Travelstar 3LP Bedienungsanleitung

IBM

IBM DCXA-210000 Bedienungsanleitung

IBM

IBM Ultrastar 18ES Bedienungsanleitung

IBM

IBM Elastic Storage System 3000 Bedienungsanleitung

IBM

IBM 3000 6.0.2 Bedienungsanleitung

IBM

IBM Ultrastar 36Z15 Bedienungsanleitung

IBM

IBM DATA MIGRATION SERVICES - Bedienungsanleitung

IBM

IBM DDS Gen 5 Bedienungsanleitung

IBM

IBM DS3500 Betriebsanleitung

IBM

IBM 22P7196 - ThinkPlus Portable 40 GB External Hard... Bedienungsanleitung

IBM

IBM 1 GB Microdrive Storage Card Bedienungsanleitung

IBM

IBM Storwize V7000 Betriebsanleitung

IBM

IBM IC35L040AVVN07-0 - 40GB IDE Deskstar 120GXP 7200RPM UATA-100... Bedienungsanleitung

IBM

IBM OPTIONS 12/24 GB Bedienungsanleitung

IBM

IBM FlashSystem 820 Bedienungsanleitung

IBM

IBM DTCA-23240 - Travelstar 3.2 GB Hard Drive Bedienungsanleitung

IBM

IBM HH LTO Bedienungsanleitung

IBM

IBM Storwize V7000 Bedienungsanleitung

IBM

IBM Accesser 4105 Bedienungsanleitung

IBM

IBM Ultrastar 36XP Bedienungsanleitung

IBM

IBM DARA-206000 - Travelstar 12 GB Hard Drive Bedienungsanleitung

IBM

IBM Travelstar 40GNX Bedienungsanleitung

IBM

IBM IC35L020 - Deskstar 20 GB Hard Drive Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung