Icom IC-2200H Bedienungsanleitung
I
QUICK REFERENCE GUIDE
■Installation
DLocation
Select a location which can support the weight of the trans-
ceiver and does not interfere with driving in any way. We rec-
ommend the locations shown in the diagram below.
NEVER place the transceiver where normal operation of the
vehicle may be hindered or where it could cause bodily injury.
NEVER place the transceiver where air bag deployment may
be obstructed.
DO NOT place the transceiver where hot or cold air blows di-
rectly onto it.
AVOID placing the transceiver in direct sunlight.
DUsing the mounting bracket
➀Drill 4 holes where the mounting bracket is to be installed.
•Approx. 5.5–6 mm (1⁄4″) when using nuts; approx. 2–3 mm (1⁄8″)
when using self-tapping screws.
➁Insert the supplied screws, nuts and washers through the
mounting bracket and tighten.
➂Adjust the angle for the clearest view of the function dis-
play.
IMPORTANT!
Detailed installation notes for Icom mobile transceivers to
be fitted into vehicles are available. Contact your Icom
dealer or distributor.
Nut
Spring washer
Flat washer
When using
self-tapping
screws
Spring
washer
Mounting
nut
Mounting
bracket
II
QUICK REFERENCE GUIDE
DBattery connection
☞NEVER connect the transceiver directly to a 24 V battery.
☞DO NOT use the cigarette lighter socket for power con-
nections. (See p. 5 for details)
Attach a rubber grommet when passing the DC power cable
through a metal plate to prevent short circuiting.
•CONNECTING TO A DC POWER SOURCE
•See p. 90 for fuse replacement.
DDC power supply connection
Use a 13.8 V DC power supply with at least 15 A capacity.
Make sure the ground terminal of the DC power supply is
grounded.
•CONNECTING TO A DC POWER SUPPLY
•See p. 90 for fuse replacement.
DC power
supply 13.8 V
to an
AC
outlet
Fuses
20 A
black
red⊕
−
⊕
−
IC-2200H
Fuses
20 A
Crimp Solder
black
red⊕
Grommet
IC-2200H
−
12 V 12 V
battery Supplied
DC power cable
NOTE:
Use terminals for the
cable connections.
+red
_black
III
QUICK REFERENCE GUIDE
DAntenna installation
•Antenna location
To obtain maximum performance from the transceiver, select
a high-quality antenna and mount it in a good location. A non-
radial antenna should be used when using a magnetic mount.
•Antenna connector
The antenna uses a PL-259 connector.
•PL-259 CONNECTOR
qSlide the coupling ring
down. Strip the cable
jacket and soft solder.
wStrip the cable as shown
at left. Soft solder the cen-
ter conductor.
eSlide the connector body
on and solder it.
rScrew the coupling ring
onto the connector body.
(10 mm ≈3⁄8 in)
NOTE: There are many publications covering proper an-
tennas and their installation. Check with your local dealer
for more information and recommendations.
DConnecting a microphone
Connect a microphone to the eight-pin modular socket on the
front panel of the transceiver.
*HM-133V; A different microphone may be
supplied with some versions of the IC-2200H.
30 mm
10 mm (soft solder)
10 mm
1–2 mm
solder solder
Soft
solder
Coupling ring
to antenna
Roof-mount antenna
(Drill a hole or use a magnetic mount.)
Gutter-mount antenna
Trunk-mount
antenna
IV
QUICK REFERENCE GUIDE
■Your first contact
Now that you have your IC-2200H installed in your car or
shack, you are probably excited to get on the air. We would
like to take you through a few basic operation steps to make
your first “On The Air” an enjoyable experience.
1. Turning ON the transceiver
Before powering up your IC-2200H, you may want to make
sure the audio volume and squelch level controls are set in
9–10 o’clock positions.
Although you have purchased a brand new transceiver, some
settings may be changed from the factory defaults because
of the QC process. Resetting the CPU is necessary to start
from factory default.
➥While pushing [SET ] and [S.MW ], push
[PWR] for 1 sec. to reset the CPU.
2. Tune the desired frequency
[DIAL] will allow you to dial in the frequency you want to op-
erate. Pages 9 and 11 will instruct you on how to set the tun-
ing speed.
Using the HM-133V
You can directly enter the frequency with the HM-133V keypad.
We hope these pointers have been helpful. Now you
are ready to call CQ.
LOCK
S
E
TANM
MONI DUP
LOW
T-SCAN
TONE PRIO
M/CALL SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK
S
E
TANM
MONI DUP
LOW
T-SCAN
TONE PRIO
M/CALL SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK
S
E
TANM
MONI DUP
LOW
T-SCAN
TONE PRIO
M/CALL SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK
S
E
TANM
MONI DUP
LOW
T-SCAN
TONE PRIO
M/CALL SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
[EXAMPLE]: Setting frequency to 145.3625 MHz.
Push
Push
Push
Push
[DIAL]
MWLOCK
[PWR]
[SET LOCK][S.MW MW]
Set both [VOL] and [SQL] controls to
9–10 o’clock positions.
[VOL]
[SQL]
V
QUICK REFERENCE GUIDE
■Repeater operation
1. Setting duplex
Push [LOW ] for 1 sec. once or twice to select minus
duplex or plus duplex.
•The USA version has an auto repeater function, therefore, setting
duplex is not required.
2. Repeater tone
Push [TONE ] several times until “ ” appears, if the
repeater requires a subaudible to be accessed.
Using the HM-133V
Plus or minus duplex selection and the repeater tone setting
can be made easily via HM-133V.
Push [
DUP
–7(TONE)] for minus duplex; [
DUP
+8(TSQLSS)]
for plus duplex selection, push [FUNC] then [
DUP
–7(TONE)]
to turn the repeater tone ON.
LOCK
S
E
TANM
MONI DUP
LOW
T-SCAN
TONE PRIO
M/CALL SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK
S
E
TANM
MONI DUP
LOW
T-SCAN
TONE PRIO
M/CALL SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK
S
E
TANM
MONI DUP
LOW
T-SCAN
TONE PRIO
M/CALL SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
Push
Push , then
Push
LOCK
S
E
TANM
MONI DUP
LOW
T-SCAN
TONE PRIO
M/CALL SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
T-SCAN
LOCK
S
E
TANM
MONI DUP
LOW
T-SCAN
TONE PRIO
M/CALL SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
DUP
The IC-2200H has a total of 207 memory channels (including
6 scan edges and 1 call channel) for storing often used oper-
ating frequency, repeater settings, etc.
1. Setting a frequency
In VFO mode, set the desired operating frequency with re-
peater, tone and tuning steps, etc.
2. Selecting a memory channel
Momentarily push [S.MW ], then rotate [DIAL] to select
the desired memory channel.
•“M” indicator and memory channel number blink.
3. Writing a memory channel
Push and hold [S.MW ] for 1 sec. to program.
•3beeps sound
•Memory channel number automatically increases when continuing
to push [S.MW ] after programming.
Using the HM-133V
qIn VFO mode, set the desired operating frequency, includ-
ing offset direction, tone settings, etc.
wPush [FUNC] then [
CLR
A(MW)].
•“M” indicator and memory channel number blink.
ePush [YY]/[ZZ]to select the desired memory channel.
rPush [FUNC] then push [
CLR
A(MW)] for 1 sec. to pro-
gram.
•3beeps sound
•Memory channel number automatically increases when continu-
ing to push [
CLR
A(MW)] after programming.
LOCK
S
E
TANM
MONI DUP
LOW
T-SCAN
TONE PRIO
M/CALL SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
Push ,
then
MW
MW
LOCK
S
E
TANM
MONI DUP
LOW
T-SCAN
TONE PRIO
M/CALL SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
[S.MW MW] [DIAL]
MW
■Programming memory channels
VI
QUICK REFERENCE GUIDE
Andere Handbücher für IC-2200H
7
Inhaltsverzeichnis
Andere Icom Radio Handbücher
Icom
Icom IC-F40GT Bedienungsanleitung
Icom
Icom IC-R71A Bedienungsanleitung
Icom
Icom ID-52A Bedienungsanleitung
Icom
Icom M302 Gebrauchsanweisung
Icom
Icom IC-F3160 SERIES Handbuch
Icom
Icom IC-706MKIIG Bedienungsanleitung
Icom
Icom RMK-4 Bedienungsanleitung
Icom
Icom IC-F5061 Bauanleitung
Icom
Icom IC-F14 Montage- und Bedienungsanleitung
Icom
Icom IC-F1010 Bedienungsanleitung
Icom
Icom IC-F4TR Leitfaden
Icom
Icom IC-F43TR Bedienungsanleitung
Icom
Icom iF610 Bedienungsanleitung
Icom
Icom 9000 F70 Series Installationsanleitung
Icom
Icom IC-F43TR Bedienungsanleitung
Icom
Icom IC-211 Handbuch
Icom
Icom IC-2A Bedienungsanleitung
Icom
Icom IC-7100 Bedienungsanleitung
Icom
Icom A25C SPORT 66 USA Benutzerhandbuch
Icom
Icom IC-SAT100M Bedienungsanleitung
