Icom IC-F3033S Bedienungsanleitung

INSTRUCTION MANUAL

This device complies with Part 15 of the FCC

Rules. Operation is subject to the condition that

this device does not cause harmful interference.

iF3033S

iF3031S

VHF TRANSCEIVERS

iF3036S

iF4033S

iF4031S

UHF TRANSCEIVERS

iF4036S

The photo shows the

VHF transceiver

READ ALL INSTRUCTIONS carefully and com-

pletely before using the transceiver.

SAVE THIS INSTRUCTION MANUAL — This

instruction manual contains important operating instructions

for the IC-F3031S, IC-F3033S, IC-F3036S VHF TRANS-

CEIVERS and the IC-F4031S, IC-F4033S, IC-F4036S UHF

TRANSCEIVERS.

This instruction manual includes some functions which are

usable only when they are pre-programmed by your dealer.

Ask your dealer for details.

For Canada:

This device complies with RSS-310 of Industry Canada. Op-

eration is subject to the condition that this device does not

cause harmful interference.

Cet appareil est conforme au CNR-310 d’Industrie Canada.

Son exploitation est autorisée sous réserve que l’appareil ne

cause pas de brouillage préjudiciable.

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-

porated (Japan) in Japan, the United States, the United Kingdom, Germany,

France, Spain, Russia and/or other countries.

EXPLICIT DEFINITIONS

WORD DEFINITION

RDANGER! Personal death, serious injury or an ex-

plosion may occur.

RWARNING! Personal injury, ﬁre hazard or electric

shock may occur.

CAUTION Equipment damage may occur.

NOTE If disregarded, inconvenience only. No risk

of personal injury, ﬁre or electric shock.

IMPORTANT

CAUTION: MAKE SURE the ﬂexible antenna, bat-

tery pack and jack cover are securely attached to the trans-

ceiver, and that the antenna and battery pack are dry before

attachment. Exposing the inside of the transceiver to dust or

water will result in serious damage to the transceiver.

DO NOT operate the transceiver near unshielded electri-

cal blasting caps or in an explosive atmosphere.

DO NOT

push [PTT] when not actually intending to transmit.

DO NOT use or place the transceiver in direct sunlight or

in areas with temperatures below –30°C (–22°F) or above

+60°C (+140°F).

The basic operations, transmission and reception of the

transceiver are guaranteed within the speciﬁed operating

temperature range. However, the LCD display may not be

operate correctly, or show an indication in the case of long

hours of operation, or after being placed in extremely cold

areas.

DO NOT modify the transceiver. The transceiver warranty does

not cover any problems caused by unauthorized modiﬁcation.

DO NOT use harsh solvents such as benzine or alcohol

when cleaning, as they will damage the transceiver surfaces.

BE CAREFUL! The transceiver will become hot when

operating it continuously for long periods of time.

PRECAUTIONS

RDANGER! NEVER short the terminals of the battery

pack.

RDANGER! Use and charge only speciﬁed Icom bat-

tery packs with Icom radios or Icom chargers. Only Icom bat-

tery packs are tested and approved for use with Icom radios

or charged with Icom chargers. Using third-party or coun-

terfeit battery packs or chargers may cause smoke, ﬁre, or

cause the battery to burst.

RWARNING! NEVER hold the transceiver so that

the antenna is very close to, or touching exposed parts of

the body, especially the face or eyes, while transmitting. The

transceiver will perform best if the microphone is 5 to 10 cm

(2 to 4 inches) away from the lips and the transceiver is verti-

cal.

RWARNING! NEVER operate the transceiver with

a headset or other audio accessories at high volume levels.

Hearing experts advise against continuous high volume op-

eration. If you experience a ringing in your ears, reduce the

volume level or discontinue use.

RWARNING! NEVER operate the transceiver while

driving a vehicle. Safe driving requires your full attention—

anything less may result in an accident.

iii

FCC INFORMATION

s &/2 #,!33 ! 5.).4%.4)/.!, 2!$)!4/23

This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment

is operated in a commercial environment. This equipment

generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communi-

cations. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

BE CAREFUL! The IC-F3031S, IC-F3033S, IC-F3036S,

IC-F4031S, IC-F4033S and IC-F4036S meet IP67* require-

ments for dust-tight and waterproof protection. However,

once the transceiver has been dropped, dust-tight and water-

proof protection cannot be guaranteed because of possible

damage to the transceiver’s case or the waterproof seal.

* Only when the jack cover or the optional HM-168LWP is

attached.

Even when the transceiver power is OFF, a slight current still

ﬂows in the circuits. Remove the battery pack or batteries

from the transceiver when not using it for a long time. Other-

wise, the installed battery pack or batteries will become ex-

hausted, and will need to be recharged or replaced.

MAKE SURE to turn the transceiver power OFF before

connecting the supplied/optional equipment.

For U.S.A. only:

CAUTION: Changes or modiﬁcations to this transceiver, not

expressly approved by Icom Inc., could void your authority to

operate this transceiver under FCC regulations.

PRECAUTIONS (Continued)

TABLE OF CONTENTS

IMPORTANT..........................................................................i

EXPLICIT DEFINITIONS.......................................................i

PRECAUTIONS.................................................................... ii

FCC INFORMATION ........................................................... iii

TABLE OF CONTENTS....................................................... iv

1 ACCESSORIES ...........................................................1–2

Supplied accessoriesN...................................................1

Accessory attachmentsN................................................1

2 PANEL DESCRIPTION................................................3–7

Front panelN...................................................................3

Function displayN...........................................................4

Programmable function keysN........................................5

3 BASIC OPERATION..................................................8–14

Turning power ONN........................................................8

Channel selectionN........................................................9

Call procedureN..............................................................9

Receiving and transmittingN.........................................10

User set modeN............................................................12

Emergency CallN..........................................................12

Priority A channel selectionN........................................13

Man Down Emergency CallN........................................13

Stun functionN..............................................................13

Scrambler functionN.....................................................13

MDC 1200 system operationN.....................................14

4 BATTERY CHARGING ............................................15–19

CautionN.......................................................................15

Optional battery chargersN...........................................17

5 OPTIONAL SWIVEL BELT CLIP ............................20–21

MB-93 contentsN..........................................................20

AttachingN....................................................................20

DetachingN...................................................................21

6 SPEAKER MICROPHONE............................................22

Optional HM-168LWP descriptionN..............................22

AttachmentN.................................................................22

7 OPTIONS.................................................................23–24

8 SAFETY TRAINING INFORMATION.......................25–26

1ACCESSORIES

Supplied accessoriesN

NOTE: Some accessories are not supplied with depending

on versions.

Flexible antenna

Battery pack

Belt clip

Accessory attachmentsN

Flexible antennaD

Connect the supplied ﬂexible antenna to

the antenna connector.

CAUTION:

sNEVER carry the transceiver by

holding the antenna.

sDO NOT connect the antenna other

thanlisted on page 24.

s 4RANSMITTING WITHOUT AN ANTENNA

may damage the transceiver.

Battery packD

To attach the battery pack:

Slide the battery pack in the direction of the arrow (q) until

the battery release button makes a ‘click’ sound.

NOTE: Push on the bottom of the pack to make sure the

release button is ﬁrmly locked.

To release the battery pack:

Slide the battery release button in the direction of the arrow

(w) as shown below. The battery pack is then released.

NEVER release or attach the battery pack when the trans-

ceiver is wet or soiled. This may result water or dust get-

ting into the transceiver/battery pack and may result in the

transceiver being damaged.

Battery release button

NOTE: Keep the battery terminals clean. It's a good idea

to regularly clean them.

ACCESSORIES

Belt clipD

To attach the belt clip:

Release the battery pack if it is attached.q

w Slide the belt clip in the direction of the arrow until the belt

clip is locked and makes a ‘click’ sound.

To detach the belt clip:

Release the battery pack if it is attached.q

Pinch the clip (wq), and slide the belt clip in the direction of

the arrow (w).

Jack coverD

To attach the jack cover:

qAttach the jack cover to the [MIC/SP] jack.

wTighten the screws.

[MIC/SP] jack

Jack cover

CAUTION:

sAttach the jack cover when the op-

tional speaker-microphone is not

used.

s 5SE THE SUPPLIED SCREWS ONLY

To detach the jack cover:

qUnscrew the screws using a phillips

screwdriver.

wDetach the jack cover for the speak-

er-microphone or headset connec-

tion.

2PANEL DESCRIPTION

Front panelN

Microphone

Speaker

qANTENNA CONNECTOR

Connects the supplied antenna.

wDEALER-PROGRAMMABLE KEY [Emer]

Desired function can be programmed by your dealer. (p. 7)

eDEALER-PROGRAMMABLE KEY [Side1]

Desired function can be programmed by your dealer.

(p. 5)

rPTT SWITCH [PTT]

Push and hold to transmit; release to receive.

tDEALER-PROGRAMMABLE KEYS [Side2]/[Side3]

Desired functions can be programmed independently by

your dealer. (p. 5)

yDEALER-PROGRAMMABLE KEYS [P0] to [P3]

Desired functions can be programmed independently by

your dealer. (p. 5)

uFUNCTION DISPLAY (p. 4)

Displays a variety of information such as an operating

channel number/name, 2-tone code, DTMF numbers, se-

lected function and so on.

iEXTERNAL MICROPHONE/SPEAKER JACK

Connect an optional speaker-microphone.

NOTE: Connect or disconnect the optional equipment

after the transceiver is turned OFF.

Jack cover

NOTE: Attach the jack

cover when the optional

equipment is not used.

See (p. 2) for details.

oVOLUME CONTROL [VOL]

Rotate to turn the power ON/OFF and adjusts the audio

level.

PANEL DESCRIPTION

Function displayN

yq iutrew

qTRANSMIT INDICATOR

Appears while transmitting.

wBUSY INDICATOR

Appears while the channel is busy.

eSIGNAL STRENGTH INDICATOR

Indicates relative signal strength level.

rLOW POWER INDICATOR

Appears when low output power is selected.

s7HEN THE BATTERY POWER DECREASES TO ASPECIlED LEVEL LOW

power is selected automatically.

tAUDIBLE INDICATOR

±Appears when the channel is in the ‘audible’ (unmute)

condition.

Appears when the speciﬁed 2-tone code is received.±

ySCRAMBLER INDICATOR

Appears when the voice scrambler function is activated.

uBELL INDICATOR

Appears or blinks when the speciﬁc 2-tone code is re-

ceived, according to the pre-programming.

iKEY LOCK INDICATOR

Appears during the key lock function is ON.

oBATTERY INDICATOR

Appears or blinks when the battery power decreases to a

speciﬁed level.

!0 ALPHANUMERIC DISPLAY

Displays an operating channel number, channel name,

Set mode contents, DTMF code, etc.

2PANEL DESCRIPTION

Programmable function keysN

The following functions can be assigned to [Emer],[Side1],

[Side2], [Side3], [P0], [P1], [P2] and [P3] programmable

function keys.

Consult your Icom dealer or system operator for details con-

cerning your transceivers programming.

If the programmable function names are bracketed in the fol-

lowing explanations, the speciﬁc key is used to activate the

function depends on the programming.

CH UP AND DOWN KEYS

±Push to select an operating channel.

±Push to select a transmit code channel after pushing [TX

Code CH Select].

±Push to select a DTMF channel after pushing [DTMF Au-

todial].

±Push to select a scan group after pushing and holding

[Scan A Start/Stop]/[Scan B Start/Stop] for 1 second.

SIREN KEY

Push to emit a siren.

ZONE KEY

Push this key, then push [CH Up] or [CH Down] to select the

desired zone.

What is “zone”?— The desired channels are assigned

into a zone according to the intended use for grouping.

For example, ‘Staff A’ and ‘Staff B’ are assigned into a

“Business” zone, and ‘John’ and ‘Cindy’ are assigned into

a “Private” zone.

SCAN A KEY

±This key’s operation depends on the Power ON Scan set-

ting.

When the power ON scan function is turned OFF;

Push to start and cancel scanning operation. In case of

transmission during scan, scanning will be cancelled.

When the power ON scan function is turned ON;

Push to pause scanning, then resumes scanning after

passing a speciﬁed time period. In case of transmission

during scan, scanning will be cancelled.

±Push and hold this key for 1 second to indicate the scan

group, then push [CH Up] or [CH Down] to select the de-

sired group.

SCAN B KEY

±Push to start and cancel scanning operation. In case of

transmission during scan, scanning will be paused. Then

resumes scanning after passing a speciﬁed time period.

±Push and hold this key for 1 second to indicate the scan

group, then push [CH Up] or [CH Down] to select the de-

sired group.

PRIO A/B KEYS

±Push to select Priority A or Priority B channel.

±Push and hold [Prio A (Rewrite)] or [Prio B (Rewrite)] for 1

second to reassign the operating channel to Priority A or

Priority B channel.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte VHF-Transceiver Handbücher anderer Marken

Midland

Midland CT590 Bedienungsanleitung

Icom iC-F3033S Bedienungsanleitung

Beliebte VHF-Transceiver Handbücher anderer Marken