ICON FIRES Classic Bedienungsanleitung

Double Sided Firebox User Manual

Operating Manual

Thank you for purchasing this Icon Fires Burner. Icon Fires is very safety conscious and we have taken every care in

designing, manufacturing and assembling your Icon Fires Burner to ensure it operates effectively, efficiently and

safely. In return we ask that you exercise care when using this product and follow the instructions below. Before

using your Icon Fires Burner, please read all the information contained in this operation manual carefully. Icon Fires

cannot be held responsible for any damage or injury caused if these instructions are not followed.

IMPORTANT SAFEGUARDS

When using this Fireplace, basic precautions should always be followed, including but not limited to the following.

Read all instructions and warnings before using this Fireplace.

WARNING

•DO NOT OVERFILL THE BURNER’S INTENDED CAPACITY.

•NEVER LEAVE THE APPLIANCE UNATTENDED DURING OPERATION OR WHEN A FLAME IS PRESENT.

•DO NOT IGNITE THE COMBUSTION CHAMBER WHEN IT IS IN A HOT STATE.

•USE ONLY THE FUEL FOR WHICH THE SLIMLINE BURNER IS INTENDED.

•DO NOT TOUCH THE EXTERIOR OF THE SLIMLINE BURNER DURING OR AFTER BURNING.

•PARTS OF THIS SLIMLINE BURNER CAN REACH HIGH TEMPERATURES.

•DO NOT HAVE COMBUSTIBLE OBJECTS IN CLOSE PROXIMITY TO THE BURNER.

•UNLESS THE BURNER IS OUTDOORS, DO NOT INSTALL INTO AN AREA WHERE THERE IS A DRAFT WHICH

CAN AFFECT THE FLAME.

ESPECIALLY WHEN INSTALLING IN OLD HEARTHS, MAKE SURE HEARTH IS SEALED.

•NEVER POSITION THE BURNER WITHIN RANGE OF COMBUSTIBLE ITEMS THAT CAN BE

MOVED/BUMPED BY ACCIDENT OR BLOWN BY THE WIND. E.G. CURTAINS, BLANKETS, PAPERS ETC...

•ONLY USE THE SLIMLINE BURNER IN AREAS WITH GOOD VENTILATION.

•DO NOT COVER THE SLIMLINE BURNER VENT WITH ANY DECORATIVE ITEMS WHETHER THEY ARE

COMBUSTIBLE OR NON-COMBUSTIBLE, INCLUDING BUT NOT LIMITED TO ARTIFICIAL LOGS, STONES,

PEBBLES, GLASS BEADS etc.

•THE FIREBOX BODY MUST BE INSULATED WITH A LAYER OF THERMAL CERAMIC WOOL OR SIMILAR

MATERIAL THAT CAN WITHSTAND CONSTANT TEMPERATURES OF 300 ℃.

•THE INSULATION MUST COVER THE ENTIRE FIREBOX BODYAND BE FIXED SECURELY SO THAT NO

COMBUSTIBLE MATERIAL INSIDE THE WALL CAVITY CAN TOUCH THE FIREBOX. THE BODY OF THE

FIREBOX CAN REACH TEMPERATURES OF UP TO 200 ℃.

•CUSTOMS INSTALLATION: ICON FIRES IS NOT LIABLE FOR ANY INJURIES OR DAMAGES SUSTAINED BY

CUSTOM MADE OR PRIVATELY COMISSIONED FIREBOXES. ICON FIRES RECOMMENDS USING THE

BURNERS IN THE FIREBOXES MANUFACTURED BY ICON FIRES ONLY. ANY ALTERATIONS TO THE ICON

PRODUCT VOIDS ANY WARRANTY OR LIABILITY.

•WARNING: FILLING AND ALCOHOL FUELLED DEVICE WHILE LIT HAS CAUSED SEVERE BURNS AND

DEATHS. WHEN REFILLING FIRST CHECK THE FLAME IS EXTINGUESHED AND THAT THE DEVICE IS

COOL.

CAUTION

•Make sure you have read and understood this manual before using this product.

•Do not overfill or spill fuel when refilling.

•If fuel is spilt onto the surface of the Firebox WIPE IT IMMEDIATELY AND LEAVE TO DRY BEFORE LIGHTING THE BURNER.

•If fuel is spilled on the stainless steel Burner during filling, wipe with a dry cloth and allow the rest to

evaporate before lighting the Burner.

•If the Burner is accidentally overfilled, follow the steps in the Burner manual to rectify.

•To refill, wait until the Burner is at the room temperature after the flame has been turned off.

NOTE: the flame may not be visible to the naked eye in daylight and must be cool before filling.

•NEVER refill over or near an open flame and use a decanter with a flame arrestor only.

•Remove all plastic & packaging before using the Burner.

CONTENT OF PACKAGING DOUBLE SIDED FIREBOX:

•Base Plate - qty 1

•Side Plates - qty 2

•Top Plate - qty 1

•Fascia Assemblies - qty 2 (Packaged separately)

•Bolts and Washers - qty varies for each model size

Wall BoxTop Plate

Wall BoxSide Plate

Fascia Assembly

Burner Cut Out

Wall BoxBase Plate

Double Sided Firebox Assembled

Fascia Assembly

NOTE: The Firebox has been designed to be built into many different materials and

environments, and due to this fact, we cannot provide instructions for each and every

possible situation. We advise that you use only certified builders or installation specialists

who will exercise the necessary precaution needed. Please refer to the Technical

Specification Sheets for more detailed dimensions for each size in the Firebox Range.

1 - Product Specifications for Double Sided Fireboxes

NB... There must be a

minimum of 13mm

clearance from anything,

all around the Wall Box.

Wall surface material

13 opening cutout width - C 13

overall fascia width - A

eq fuel tank clearance - G eq

10 10

space below for fuel

tank of burner

Top View

25.5 cutout depth - E

overall unit depth - F

25.5

overall fascia width - A

opening cutout width - C 1010

overall fascia height - B

cutout height - D

83 10

Front View

space below for fuel tank of burner

fuel tank clearance - G

eq eq

83 opening cutout height - D 10

overall fascia height - B

Side View

space below

for fuel tank

of burner

161 128 161

25.5 cutout depth - E

overall unit depth - F

25.5

Overall Product Sizes - Slimline Double Sided Firebox:

A = Fascia Width

and model nr.

B = Fascia Height

C = Cut-out

*Opening Width

D = Cut-out

*Opening Height

E = Minimum

Cut-out Depth

F = Overall Unit

Depth

G = Fuel Tank

Clearance

1100mm

600mm

1080mm

567mm

450mm

500mm

830mm

1350mm

600mm

1330mm

567mm

450mm

500mm

1130mm

1650mm

600mm

1630mm

567mm

450mm

500mm

1430mm

2000mm

600mm

1980mm

567mm

450mm

500mm

1430mm

2000mm *

600mm

1980mm

567mm

450mm

500mm

1680mm

2000mm is with 1 x 1400 Slimline Burner and 2000* is with dual 800 Slimline Burners

Overall Product Sizes –Commercial Double Sided Firebox:

Size Burners

A = Fascia

Width

B = Fascia

Height

C = Cut-out

*Opening

Width

D = Cut-out

*Opening

Height

E = Minimum

Cut-out

Depth

F = Overall

Depth

G = Fuel Tank

Clearance

Classic &

MB614

900mm

600mm

880mm

567mm

450mm

500mm

600mm

Grand XL &

LB914

1100mm

600mm

1080mm

567mm

450mm

500mm

900mm

* Cut out opening width and height is the opening size of the cut out in the wall surface onto which the Fireplace fascia is ultimately placed

against. All other construction materials that are positioned behind the face of the wall must have a minimum 25mm clearance to the surface

of insulation wrapped around the exterior Firebox body.

2 - Assembly Instructions - Double Sided

Place the base plate flat and fix the side plates to the base plate with the fasteners and

washers provided. Do not tighten the fasteners completely. Hand fasten only as you might

need to make a positioning and adjustments when the other plates are attached.

Lastly fasten the top plate to the side plates. Make sure all the plates fit together and that

there are no gaps visible between the plates. Fasten all the screws tightly. Your Firebox is

now ready to be installed.

READ CAREFULLY

•The Firebox body that sits inside the wall cavity must be insulated with a layer of insulation

material such as rock wool or ceramic blanket that can handle continuous exposure of 300 ℃.

The entire Firebox body must be isolated from any combustible material inside the wall cavity.

The insulation must be securely fixed onto the body of the Firebox. No combustible materials

may touch the surface of the Firebox body.

•Make sure that the Firebox is installed no closer than 1m (40 inch) from any combustible items

such as furniture, curtains, etc. See image on the next page in this section. This excludes the

actual structure in which the Firebox is placed if the Firebox is thermally insulated. The floor

below the Firebox, inside the wall cavity, must be insulated and cannot be made from

combustible material. Wooden floors, plastic based flooring, carpets etc. are not allowed.

•When installing into old hearths or new structures ensure that you create ventilation openings

above and below the position of the Fireplace in the old hearth or new structure.

•Take care when placing valuable items such as artwork, electronic devices, etc. above the

Firebox as the hot air that rises from the flame may damage such items.

•Position the Firebox where it will not be affected by any breeze or draft, as this may affect the

behaviour of the flame in an unpredictable manner.

•Never cover the fascia opening of the Firebox at any time.

•It is advisable to consider children and pets when selecting a position to install the Firebox.

Ensure that the fire is never left unattended.

•Install a vent above and below the Firebox to allow for ventilation should a spill occur.

CLEANING & MAINTENANCE FOR COMMERCIAL & SLIMLINE FIREBOXES:

The internal areas of the Firebox can change in appearance with time and usage. This is

to be considered normal wear and tear and does not constitute a product flaw or fault.

We recommend cleaning the internal surfaces with a moist lint-free cloth.

ALWAYS KEEP HANDY A CLASS ABE FIRE EXTINGUISHER:

Class ABE fire extinguishers are used to put out fires that are caused by combustible liquids. Class

ABE fire extinguishers quell the flames by expelling a dry chemical powder or foam with a nitrogen

propellant. The specific chemical can vary depending on the make or model. Water will not

extinguish this flame.

3 - Location, Positioning & Precautions

Sectional Top View - Double Sided

Diamond shaped lines indicate

thermal insulation. The entire

body of the Firebox must be

covered with the insulation.

cutout width

13 wall box overall size 13

10 13

Typical timber framework

as an example

NB... There must be a

minimum of 13mm

clearance from anything,

all around the Wall Box.

Wall surface material

Note: The drawings above are an example of a typical installation using framework and

covering the Firebox body with insulation. All installations must comply with the relevant

building regulations and restrictions of the country where the installation is to take place.

Minimum

1000mm from

combustible

material

Min. 1m

Minimum

300mm to floor

floor must be

non combustible

PRECAUTION

RISK OF EXPLOSION

To avoid a build-up of fuel vapour in the cavity, it must be vented and checked for any

possible spillage or leaks.

Should the burner be over filled or leak into the wall cavity void, please remove the burner

to check and to thoroughly clean up any fuel spillage. Make sure the area is dry and

clean, before replacing the burner. The area will need to be well vented for a minimum of

24 hours before igniting the burner.

Typical framework

as an example

4 - Installation Procedure

Always use a certified builder or installation specialist when installing your Firebox. Use only

fire rated materials which adhere to the relevant laws and building regulations in the

country where the installation is to occur and make sure that spacing tolerances are

always adhered to and that the correct insulation materials has been used. Below is an

example of a typical installation.

Step 1:

Create your Firebox display structure from fire rated building materials with enough

support below for the Firebox to rest on. Your structure must have a vent above and below

the Fireplace, these vents can also be on the side of your structure and hidden out of

sight.

Fire rated timber framework

Firecheck Plasterboard

Important:

Insulation must be

securely wrapped

around the Wall Box

before placing inside

opening. Wall Boxof Firebox

wrapped with insulation

all around the outside

Fascia

Assembly

of Firebox

Cutout opening size as

per tables in this manual

Adequate support below

Wall Boxwith opening

below for Burner Fuel Tank Vent Grill below

Vent Grill above

Framework

Firecheck Fire Related Material

Step 2:

Insert the Wall Box into the opening. Ensure the Firebox is level both horizontally and

vertically before placing the Burner inside the Firebox base cut out. Remember to leave

adequate space for the Burner to drop down into the void below the Firebox. Wrap the

Firebox with the thermal insulation material before inserting into the wall cavity. Ensure the

insulation is securely fastened and that all parts of the Fireplace body are covered by the

insulation. No combustible materials may touch the fire box body if not insulated.

Important:

Insulation must be

securely wrapped

around the Wall Box

before placing inside

opening.

Step 3:

Place the Burner into cut out and attach the fascia to the hooks on the front of the

Firebox. Your Firebox is now ready for use. Please consult the bioethanol Burner manual

supplied with your Burner for the safety precautions and operating procedure of the

Burner.

ICON Fires warranty Terms and Conditions

1. All warranty claims are subject to manufacturer’s review and acceptance.

2. Icon Fires warrants that it uses reasonable care and skill to ensure that its products are of

reasonable quality. Icon Fires will at it's cost and in it's sole discretion: (i) remedy any defect

or fault in any product purchased; or (ii) replace any product in respect of which there is a

defect or fault, during the warranty period, provided that written notice is given by the

Purchaser to Icon Fires of any such defect or fault in the product as soon as the Purchaser

becomes aware of that fault or defect. All warranty claims must be returned to Icon Fires

for assessment with a receipt or other proof of payment. No warranty is given in respect of

any glass contained in any product.

3. Icon Fires has no liability to remedy any defect in a product or replace a

product where the defect or fault is caused or contributed to by (i) the failure of the

Purchaser to install the product according to specific installation instructions either

supplied within each product box or carton or available on the Icon Fires website or

through the retailer representative; or (ii) use of the product in a manner or for a purpose

for which it was not designed.

4. All site application or installation must reflect these procedures otherwise the product

warranty will be considered void or will not take effect.

All products bearing the logo of Icon Fires logo is covered by a 2 year

warranty.

IMPORTANT:

•Stone chipping, painting scratches and general scratches are not covered by the

Warranty.

•Due to the characteristics of Stainless Steel, over time the finish will mature through

natural processes associated with the use with heat and a flame.

•Is it recommended the Stainless Steel Components be polished annually with a non

abrasive polish to bring & restore the finish and also to regularly clean the products from

residue and dirt.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ICON FIRES Heizung Handbücher

ICON FIRES

ICON FIRES MB 614 Montageanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung