ICON Utrack Pro Bedienungsanleitung
4-In / 4-Out Recording USB Interface
withMIDI&S/PDIFI/O
N16549
COMP DIRECT
OUT
MIX
HP
MONITOR
MIDI I/O
S/PDIF
USB
Important Safety Instructions
1. all manufacturer's warnings and instructions
2. Do not use this apparatus near water.
3. Clean only with dry cloth.
4. Do not block any ventilation openings and do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce
heat.
5. Do not defeat the safety function of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong is provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
6. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
7. Only use attachments/accessories specified by the manufacturer.
8. Unplug this apparatus during lightning storms or when unused for long periods of time.
9. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
Read
WARNING: To reduce the risk of fire or electric shock, do not expose this unit to
rain or moisture
Introduction
What's in the package
Features
Front Panel Layout
Rear Panel Layout
Driver Installation
Control Panel
Hardware Connections
Minimum System Requirements
Specifications
Services
Stacking the UtrackPro
Contents
2
3
4
5-7
8-10
1
13
14
12
15
11-12
Introduction
Please write your serial number here for future reference:
Purchased at:
Date of purchase:
Thank you for purchasing the ICON Utrack Pro Digital Audio Interface.
In these pages, you'll find a detailed description of all Utrack Pro features, a guided
tour through its front and rear panels, step-by-step instructions for its setup and
use, and full specifications.
You'll also find a warranty card in this package. Please don't forget to fill it out and
mail it.
Those registering products in this way will obtain easy access to online technical
support and will be sent updated information about this and other ICON products
in the future. As with most electronic devices, we strongly recommend you retain
the original packaging. In the unlikely event the product must be returned for
servicing, the original packaging (or reasonable equivalent) is required.
With proper care and adequate air circulation, your Utrack Pro will operate without
any trouble for many years. We recommend that you record your serial number in
the space provided below for future reference.
What's in the package?
Utrack Pro Mobile Recording Interface
Users' Manual
software CD
USB cable
12VDC Power Supply
Driver
1
Features
4 x 4 analog balanced I/O
Dual microphone/instrument preamps with gain controls, LED metering,
phantom power and input gain
Two analog inputs and four analog outputs on 1/4" TRS jacks
S/PDIF I/O on RCA coaxial connectors
Supports sampling rates from 44.1Hz to 192KHz
Two headphone outputs with assignable source and individual
volume control
Hardware Direct / PC Monitoring Adjustment knob
Supports Direct Sound, WDM, ASIO and GIGA studio
Full duplex, simultaneous record/playback
Rugged aluminum construction
The ICON Utrack Pro mobile interface audio input and output module offers
USB connectivity. Main features include:
2
COMP DIRECT
OUT
MIX
HP
MONITOR
MIDI I/O
S/PDIF
USB
COMP DIRECT
OUT
MIX
HP
MONITOR
Front Panel Layout
MIC/INST INPUTS
CLIP LED
SIGNAL LED
48V PHANTOM POWER SWITCH
INPUT GAIN LEVEL CONTROL
HARDWARE / PC MONITORING CONTROL
HEADPHONE OUTPUTS
HEADPHONE LEVEL CONTROLS
POWER SWITCH
Unbalanced Instrument and MIC level inputs. These hybrid connectors
will accept a standard three-pin XLR plug or a 1/4" TS connector.
When lit, this LED indicates clipping input level at the associated
MIC/INST input. The LED will illuminate when the signal is 3dB below
the clipping point.
When lit, this LED indicates the presence of an audio signal at the
associated MIC/INST input.
When this switch is in the IN position, +48V phantom power is
supplied to the XLR input. This phantom power circuit is suitable for
most condenser microphones.
This potentiometer controls the input level of its associated analog
MIC/Instrument/Line input.
Each of these output jacks accepts a standard 1/4" stereo TRS
headphone connector. The program signal is identical on both outputs,
with individual level regulated by the HEADPHONE LEVEL
CONTROLS. The default source selection for the headphone output is
identical to line outputs 1/2.
Each of these potentiometers controls the output level of its associated
headphone output.
This switch controls the overall power to the unit.
Hardware direct monitoring ( Clockwise - "Direct Out" ) eliminates the
latency or delay inherent in even the best internal circuitry while
listening to your input and existing tracks. You can also listen to your
input complete with effects (Counter-Clockwise - "COMP") while
recording by using extremely the low-latency ASIO monitoring
1
2
3
4
5
6
7
8
123
4567
9
3
8
9
MIDI I/O
S/PDIF
USB
Rear Panel Layput
POWER SUPPLY CONNECTOR
S/PDIF COAXIAL IN AND OUT CONNECTORS
MIDI IN AND MIDI OUT CONNECTORS
USB CONNECTOR
LINE OUTPUTS 1-4
LINE INPUTS 3 AND 4
Connect the 12VDC power supply to this jack using an AC adaptor
provided.
S/PDIF digital input and output on coaxial RCA connectors. The
digital input is selected via the Utrack Pro's control panel, while the
digital output will be sent to the coaxial .
MIDI input and output on standard 5-pin DIN connectors.
Connect to your computer's USB port with the provided USB cable.
These are balanced analog outputs on standard 1/4" TS connectors
at +4dB line level. These outputs will support standard stereo, as well
as 4 mono You may assisg any of the input channels to any of the
output channels. These may assign on the control panel .
These are balanced analog inputs on standard 1/4" TS connectors
at +4dB line level.
.
1
23456
1
2
3
4
5
6
4
Driver Installation
Please follow the below procedures step-by-step to install your Utrack Pro
and its driver.
1
2
3
4
5
Turn on your computer
Note: Do not connect the Utrack Pro to your computer yet
After you have insert the provided
Driver CD into your CD-Rom, a
Installation screen should appear as
Diagram 1, then click "Driver
Installation"
Insert Driver CD to your CD-Rom
Note: If the Installation
screen not appaer
automatically. Go to the
CD folder and
double click "Setup"
Choose "Next" when you see the
Welcome Screen as Diagram 2
Installation Wizard appear
Diagram 1
Diagram 2
Choose the loaction of the driver
and click "Next" as Diagram 3
Driver Setup
Diagram 3
Diagram 4
A window as illustrated as Diagram 4
would appear. Choose " Continue
Anyway"
Software Installation Window
Note: Although this message appear.
Utrack Pro's driver is fully tested and
supporting Window XP and Vista
5
Driver Installation (Continues)
Driver (ASIO2.0) will automatically
install and this may take some time,
please be patient and wait for the
installation set up completed as
shown on Diagram5. Then click
"Next".
Installation Start
6
7
8
Diagram 5
Diagram 6
New hardware (Utrack Pro) should
be found and
click "Next"
Found New Hardware Wizard
6
Notes: Utrack Pro only support
USB 2.0. Your computer must have
an USB2.0 port.
Now, connect the Utrack Pro to your
computer's USB port and turn on
its power switch and click "Finish".
Connect your Utrack Pro
Diagram 7
Diagram 8
9
Utrack Pro Device is found and
appear in the window. Click "Finish"
Found New Hardware Completed
Driver Installation (Continues)
Note: Although this message appear.
Utrack Pro's driver is fully tested and
supporting Window XP and Vista
WDM driver installation window
appear, click "Next"
Utrack Pro WDM Audio Driver
Utrack Pro's WDM driver installation
has completed. Click "Finish"
Driver Installation completed
Diagram 9
10
Note: For the latest driver updates please check www.icon-global.com
10
11
A window as illustrated as Diagram 4
would appear. Choose " Continue
Anyway"
Software Installation Window
Diagram 10
You may click the Utrack logo on the
system tray to luanch the Utrack Pro
Contrl Panel (Page 8).
Launch the Utrack Pro Control Panel
10
Diagram 11
Diagram 12
7
Inhaltsverzeichnis
Andere ICON USB-Schnittstelle Handbücher
Beliebte USB-Schnittstelle Handbücher anderer Marken
PASCO
PASCO SCIENCEWORKSHOP 750 Bedienungsanleitung
Phonic
Phonic FIREFLY 302 USB Bedienungsanleitung
OHAUS
OHAUS Scout STX Series Bedienungsanleitung
Denon
Denon DN-HC4500 - DJ Mixer USB Controller Bedienungsanleitung
Lutron Electronics
Lutron Electronics Stanza SZ-CI-USB-CPN5138 Bedienungsanleitung
Paradox
Paradox PMC5-TI00 Bedienungsanleitung
Thorsis Technologies
Thorsis Technologies isDNet USB Bedienungsanleitung
Thorsis Technologies
Thorsis Technologies isHRT USB Bedienungsanleitung
microHAM
microHAM DigiKeyer Bedienungsanleitung
Apogee
Apogee Jam X Bedienungsanleitung
RigExpert
RigExpert TI-3000 Bedienungsanleitung
microHAM
microHAM USB Interface II Bedienungsanleitung