ICP DAS USA LinPAC-5000 Bedienungsanleitung

ICPDAS - 1 -

C-

-5

Version 1.2, 2011/01/20

ÂWhat’s In the Box?

LP-5K module microSD card Software Utility CD Screw Driver RS-232 Cable

ÂPreparing for start-up your LinPAC-5000

Power Supply: +10V ~ +30VDC (Ex: DP-665)

http://www.icpdas.com/products/Accessories/power_supply/power_list.htm

ÂView of the LinPAC-5000

1 USB Port 6 COM 1 (RS-232)(console) 11 LED Indicator

2 Ethernet Port 7 COM 2 (RS-485) 12 microSD socket

3 Ethernet Port 8 COM 3 (RS-232) 13 VGA Port

4 Microphone-In 9 Power 14 Xboard (optional)

5 Earphone-Out 10 Frame Ground 15 Operating Modes Selector

ÂConfiguring the operating mode

Make sure the rotary

switch place in the

“0” position.

Rotary switch position Modes of operation

0 Normal mode(Default)

1 Quick mode

2 OS update mode

3 Debug mode

Others Reserved

Normal mode(Default)

The normal mode is the default mode of operation. Use this mode for more tasks and

configurations. Programs also are executed in this mode.

Quick mode

The safe mode is used to skip the LinPAC-5000 boot screen form microSD/microSDHC

card, so as to speed up the booting process.

OS update mode

The mode is a way used to update OS, and the Linux OS image was just suitable for the

LP-5000 by ICP DAS. If the LP-5000 cannot be boot or run the normal mode, please

update OS image again. Please pay attention to backup important files first before

updating OS image. For more information, please refer to “LP-5000 OS update manual”.

Debug mode

The purpose of this mode is to development by ICP DAS.

Reserved

Rotary switch position 4~9 are reserved by ICP DAS.

ICPDAS - 2 -

ÂConnect the LinPAC-5000 and Windows PC

The port is located on the right-upper corner on the LinPAC-5000. It is a

standard RS-232 serial port, and it provides TxD, RxD, GND,

non-isolated.

Start HyperTerminal by clicking on ‘Start ÆPrograms ÆAccessories

ÆCommunications ÆHyper Terminal’

In the ‘COM properties’ dialog box, please set for 115200 bits per

second, 8 data bits, no parity, 1 stop bit and no flow control to set up

the communication parameters for the COM1 port, and press ‘OK’ when

done.

ICPDAS - 3 -

ICPDAS - 4 -

Turn on the power, and user should see a message appear on the

screen, and the total process is completed.

To login LinPAC-5000 by ‘getty’ command.

ID: root

Password: root

ÂConnect the LinPAC-5000 and Linux PC

Install HyperTerminal tool in Linux PC such as minicom, gtkterm, etc.

Take minicom as an example, please refer to the following steps:

Type ’minicom -s’ to configure COM1 port, and press down and select

‘Serial port setup’.( please set for 115200 bits per second, 8 data bits,

no parity, 1 stop bit and no flow control to set up the communication

parameters for the COM1 port). Finally, press ‘Exit’.

ICPDAS - 5 -

ICPDAS - 6 -

minicom in action

To login LinPAC-5000 by ’getty’ command.

ID: root

Password: root

ÂTelent to LinPAC-5000

In HyperTerminal :

>> In Linux PC :>> In Windows PC :

ICPDAS - 7 -

ÂGet & Configure IP of LinPAC-5000

The LinPAC-5000 network setting includes two ways. One is DHCP and the

other is “Assigned IP”. DHCP is the default setting after the LinPAC-5000 is

produced and this way is easy for users. However, if your network system is

without DHCP server, then users need to configure the network setting by using

“Assigned IP”.

Boot up LinPAC-5000 and telnet to LinPAC-5000 first.

Type in “vi /etc/network/interfaces” to open the network setting file.

ÂTechnical Support

ICP DAS Website: www.icpdas.com.tw

ICP DAS Service :

[email protected]

ICPDAS - 8 -

Inhaltsverzeichnis

Andere ICP DAS USA Controller Handbücher

ICP DAS USA

ICP DAS USA CAN-8123 Einrichtungshandbuch

ICP DAS USA

ICP DAS USA NMC-9181 Installationsanleitung

ICP DAS USA

ICP DAS USA TPD-283U-H Bedienungsanleitung

ICP DAS USA

ICP DAS USA 7188XA Gebrauchsanweisung

ICP DAS USA

ICP DAS USA GRP-2841M-5GE Bedienungsanleitung

ICP DAS USA

ICP DAS USA PISO-CAN200 Bedienungsanleitung

ICP DAS USA

ICP DAS USA WISE-2841 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA ISaGRAF mPAC Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7188E3 Bedienungsanleitung

ICP DAS USA

ICP DAS USA CAN-8124 Bedienungsanleitung

ICP DAS USA

ICP DAS USA i8094A Bedienungsanleitung

ICP DAS USA

ICP DAS USA WinPAC-5000 Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7188XA Bedienungsanleitung

ICP DAS USA

ICP DAS USA LinPAC-22 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA ISaGRAF PAC Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-8411 Bedienungsanleitung

ICP DAS USA

ICP DAS USA WISE-52 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA WISE-52 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7188XB Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA WP-2000-CE7 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA LP-9821 Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7188E3D-232 Bedienungsanleitung

ICP DAS USA

ICP DAS USA TPD-433F Bedienungsanleitung

ICP DAS USA

ICP DAS USA WISE-52 Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung