Icron Icron WiRanger Bedienungsanleitung
Cable Free USB 2.0 Hub
User Guide
Powered by ExtremeUSB® Technology
Thank you for purchasing the WiRanger. Please read this guide thoroughly
before installation.
This document applies to Part Numbers: 00-00228G through 00-00230G.
FCC Radio Frequency Interference Statement Warning
The WiRanger has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. The WiRanger generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If the WiRanger does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician
for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20cm between the radiator and your body.
CE Statement
Icron Technologies Corporation declares that the WiRanger conforms to the
specifications listed below, following the provisions of the European
R&TTE directive 1999/5/EC:
Icron Technologies Corporation vakuuttaa täten että dieses produkt
tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
koskevien näiden direktiivien muiden ehtojen mukainen.
Cable Free USB 2.0 Hub
Icron Technologies Corporation déclare que le produit est conforme aux
conditions essentielles et aux dispositions relatives à la directive 1999/5/EC.
• EN 301 489-1, 301 489-17 General EMC requirements for
Radio equipment.
• EN 609 50 Safety
• EN 300-328 Technical requirements for Radio equipment.
Caution: This equipment is intended to be used in all EU and EFTA
countries. Outdoor use may be restricted to certain frequencies and/or may
require a license for operation. Contact local Authority for procedure to
follow.
Note: Combinations of power levels and antennas resulting in a radiated
power level of above 100 mW equivalent isotropic radiated power (EIRP)
are considered as not compliant with the above mentioned directive and are
not allowed for use within the European community and countries that have
adopted the European R&TTE directive 1999/5/EC.
For more details on legal combinations of power levels and antennas, contact
Icron Technologies Corporation.
Belgique:
Dans le cas d'une utilisation privée, à l'extérieur d'un bâtiment, au-dessus
d'un espace public, aucun enregistrement n'est nécessaire pour une distance
de moins de 300m. Pour une distance supérieure à 300m un enregistrement
auprès de l'IBPT est requise. Pour une utilisation publique à l'extérieur de
bâtiments, une licence de l'IBPT est requise. Pour les enregistrements et
licences, veuillez contacter l'IBPT.
France:
2.4 GHz Bande : les canaux 10, 11 (2457 et 2462 MHz respectivement) sont
complétement libres d'utilisation en France (en utilisation intérieur). Pour ce
qui est des autres canaux, ils peuvent être soumis à autorisation selon le
départment. L'utilisation en extérieur est soumis à autorisation préalable et
très restreint. Vous pouvez contacter l'Autorité de Régulation des
Télécommunications (http://www.art-telecom.fr) pour de plus amples
renseignements.
SAFETY NOTICES
Caution: Do not use this product near water, for example, in a wet basement
or near a swimming pool.
Avoid using this product during an electrical storm. There may be a remote
risk of electric shock from lightning.
IC Statement
This Class B digital apparatus complies with Canadian ICES-003 and
RSS210 rules.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 et
CNR210 du Canada.
The use of this device in a system operating either partially or completely
outdoors may require the user to obtain a license for the system according to
the Canadian regulations.
To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that permitted for successful communication.
This device has been designed to operate with the antennas listed below, and
having a maximum gain of 2.0 dBi @ 2.4GHz. Antennas not included in this
list or having a gain greater than 2.0 dBi @ 2.4GHz are strictly prohibited
for use with this device. The required antenna impedance is 50 Ohms.
©2007 Icron Technologies Corporation. All rights reserved. Icron
Technologies Corporation, the Icron Technologies Corporation logo, and the
Icron Technologies Corporation products referred to herein are either the
trademarks or the registered trademarks of Icron Technologies Corporation.
All other trademarks are property of their respective owners. Icron
Technologies Corporation assumes no responsibility for errors that may
appear in this manual. Information contained herein is subject to change
without notice.
User Guide
i
Contents
Introduction................................................................................................ 1
WiRanger Product Contents....................................................................... 1
About the WiRanger .................................................................................. 2
Before You Begin ...................................................................................... 7
Installing the LEX unit............................................................................... 7
Installing the REX unit .............................................................................. 7
Establishing Wireless Communication ...................................................... 7
Checking the Installation............................................................................ 8
Connecting a USB Device ......................................................................... 8
Advanced Setup – Viewing and Changing the 802.11g Radio Channel.... 9
Advanced Setup – Pairing a LEX unit and a REX unit............................ 12
Troubleshooting....................................................................................... 14
Specifications........................................................................................... 18
Limited Hardware Warranty.................................................................... 19
Hardware Remedies................................................................................. 19
Limitation of Liability.............................................................................. 19
Obtaining Warranty Service..................................................................... 20
Contacting Technical Support.................................................................. 20
ii
Notes
User Guide
1
Introduction
This manual explains the installation and operation of the WiRanger – Cable
Free USB 2.0 Hub. The instructions in this guide assume a general
knowledge of computer installation procedures, wireless network installation
requirements, and some understanding of USB devices.
NOTE:Notes give additional information that could make
installation easier.
WiRanger Product Contents
When you open your WiRanger for the first time you should find the
following items:
• Local EXtender unit or LEX unit (includes antenna)
• Remote EXtender unit or REX unit (includes antenna)
• Two (2) AC power adapters
• One (1) USB cable (2m long)
• WiRanger User Guide
• WiRanger Quick Start Guide
To complete the installation, you will also require the following items that
are not included with the product:
• USB 1.1 or 2.0 compatible computer
• USB device(s)
NOTE: The WiRanger uses an IEEE 802.11g radio platform to
wirelessly communicate between the LEX unit and the REX
unit using the 2.4GHz radio frequency range. Other
products, such as wireless routers and 2.4GHz cordless
telephones, also broadcast in this same 2.4GHz range. Please
be aware of potential interference issues with such products
before you begin installation of the WiRanger.
NOTE: The LEX unit and the REX unit of your new WiRanger have
been “Paired” during manufacturing. This means that they
will only communciate with each other, even if other
WiRanger units are installed near by.
NOTE: Use only the AC adapters supplied with the WiRanger. Use
of substitute adapters may cause permanent damage to the
system and will void the warranty.
2
About the WiRanger
The WiRanger is the world’s first wireless USB 2.0 Hub, combining Icron’s
patented ExtremeUSB® technology and an industry standard IEEE 802.11g
radio. The WiRanger Hub enables wireless connection of USB devices up to
30 meters from the host computer.
The WiRanger installs as a Generic USB Hub and requires no additional
software drivers to be installed. It is composed of two individual units, the
LEX unit, which connects to the host computer, and the REX unit, which
connects to the remote USB device(s).
The LEX unit
The LEX unit connects to the host computer using a conventional USB
cable. It also connects to a power outlet through an AC power adapter.
Front
View
1 2 3 54
Activity
Host
Link
Power
Rear
View
9
876
1Power LED
2Link LED
3Host LED
4Activity LED
5Infra Red (IR) Port*
6Power connector (5V @ 3A)
7Pair/Channel Change Button**
8Host port (USB Type-B)
9Antenna connector
* IR port used to pair the LEX unit and the REX unit only
** Pair/CH button is for advanced users only. See Pages 9 and 12 for advanced instructions.
User Guide
3
The REX unit
The REX unit allows you to connect up to four USB devices directly;
additional devices may be connected by attaching a conventional USB
hub to one of the device ports. The REX unit also connects to a power
outlet through an AC power adapter.
Front
View
2 2 2 2
1 1 1 1
7
6543
Activity
Host
Link
Power
Rear
View
1098
1Device ports (USB Type-A)
2Device LED’s
3Power LED
4Link LED
5Host LED
6Activity LED
7Infra Red (IR) Port*
8Power connector (5V @ 3A)
9Pair/Channel Change Button**
10 Antenna connector
* IR port used to pair the LEX unit and the REX unit only
** Pair/CH button is for advanced users only. See Pages 9 and 12 for advanced instructions.
4
WiRanger LED Descriptions
The WiRanger uses LED’s to indicate status to the user. LED operation
is the same for the LEX unit and the REX unit.
LED Name Description
Power LED Indicates 5V power is connected to the unit.
Link LED Indicates communications have been established
between the LEX unit and the REX unit.
Independent of USB communication.
Host LED Indicates successful communications between the
host PC and the USB 2.0 hub in the REX unit.
Activity LED Indicates active USB data transmission and/or
reception over the wireless link. Additionally, the
Activity LED will flash after power is connected to
indicate that the radios are powering up
Device LED’s
(REX unit only) GREEN: Indicates that the attached USB device is
correctly detected by the host PC.
ORANGE: Indicates that the attached USB device
has drawn too much current and hence the hub
has shut this Device port off to protect the
WiRanger. Disconnect and reconnect the REX
unit’s power to clear this fault condition.
Andere Handbücher für Icron WiRanger
1
Inhaltsverzeichnis
Andere Icron Schalten Handbücher
