ICS Auto Sentry-eXP Leitfaden

Auto Sentry-eXP

Maintenance

Revised 12/21/07

Maintenance Procedures

for Auto Sentry eXP

for Auto Sentry eXP®

Bill Dispenser

Credit Card Reader

Bill Acceptor

Bill Dispenser

Maintenance

•Bill Dispenser Problem / Cause

•Bill Dispenser Error Codes

•Cleaning Pick Assembly Feed Rollers

•Cleaning the Bill Dispenser Belts

•Cleaning and Testing Sensors

•Bill Dispenser Removal Procedure

•MDS Sensor Adjustment Procedure

•Bill Cassette and Cavity Checks

Fujitsu Bill Dispenser

Problem / Cause

•High Bill rejection rate

– Place only dollar bills in good condition in Bill Dispenser cartridge

– Stack dollars neatly in cassette

– Clean MDS sensor area including metal rollers and clear Mylar scrapers

– Check MDS sensor reading in RAS mode 60 (E7 +4) E3 through EB

– Clean BPS sensors and prism

– Tighten white rails in Bill Dispenser cavity

•Bill jams/miss feeds in bill cassette cavity

– Clean black pick wheels and green feed rolls

–CleanPS1sensor and prism

– Check Bill Dispenser cassette metal tab on frame

– Tighten white rails in Bill Dispenser cavity

•Rejected bills not detected

– Clean Reject sensor

•Jams at Bill Dispenser feed out

– Check that feed out rolls turn when green wheel is turned

– Clean CPS sensor

– Replace worn anti-static brush

•Jams (general)

– Clean all feed rolls, feed belts, and Pick wheels

– Check drive belt tension

– Check Sensor Health Screen in Diagnostics and clean sensors if necessary

– Clean clock wheel and sensor

Auto Sentry eXP

Error Code Reporting

for the Bill Dispenser

• 1800 – PS1 Sensor – No bills in cassette- Pick Assembly Open?

• 7001 – PS1 Sensor – Bill jammed in PS1 sensor

• 7006 – BPS Sensor – Check for Bill in BPS sensor

• 7009 – CPS Sensor – Check for Bill in CPS sensor

• 700B – RJS Sensor – Bill remaining RJS sensor

• 7081 – BPS Sensor – Bill remaining between PS1 and BPS sensor

• 7801 - This error indicates that there may be a Bill jammed in the PS1 sensor located

behind the bill cassette.

• 7811 - Jam occurred between PS1 and BPS

• 7820 - Look for a Bill blocking the PS1 sensor

• 782C – RJS Sensor

• 7830 - PS1 Bill remaining after completion of cleaning jam

• 7900 - Check for a jammed Bill in the area of the BPS sensor and remove if found

• 7928 - Check for a jammed Bill in the area of the BPS sensor

• 7930 - PS1 Bill detected

• 7938 - BPS Bill remaining after completion of cleaning

• 7A01 - Open up the Bill Dispenser and Clear the jam between BPS and CPS

• 7A02 - Open the Bill Dispenser and Clear the Jam near CPS Sensor

Auto Sentry eXP

Error Code Reporting

for the Bill Dispenser

• 7A2B - Check the CPS sensor and put it back in its position

• 7A3A - Check for remaining Bill in dispense path (around BPS)

• 7B00 - Open the Bill Dispenser and remove the jammed Bill between BPS - RJS sensor

• 7B30 - Check RJS sensor to make sure it is back in its normal place

• 7B3C - Remove any Bills in dispense path (around RJS)

• F800 – PS1 Sensor Error – Clean sensor or replace

• F805 – BPS Sensor Error – Clean sensor or replace

• F808 – CPS Sensor Error – Clean sensor or replace

• F809 – RJS Sensor Error – Clean sensor or replace

• 8200 – BPS Sensor –Bill Read Error – Long Bill

• 8300 - BPS Sensor –Bill Read Error – Short Bill

• 8501 – PS1 Sensor - Count mismatch (CPS was turned ON when there was no Bill.)

• 8800 – CPS Sensor Count mismatch (Number of requested notes = number of notes identified as

normal = number of notes that passed through CPS does not hold.)

• 8801 – CPS Sensor

• 8803 – CPS Sensor - Count mismatch (Bill passed through CPS while clearing jam.)

• B5xx – RJS Sensor

• Exxx – PCB Replacement

Checking Bill Dispenser Health

• Pressing either End of

Day Switch will bring up

the Service Unit (Jack

Pot) Screen.

Bill Dispenser Heath

•Check the Bill

Dispenser

Sensor Health

periodically.

•The individual

Sensor Health

can be

checked from

the Service

Unit (Jack Pot)

Screen.

•Touch the

Diagnostics

Button

Bill Dispenser Heath

The individual

Sensor Health

is indicated via

a traffic light

display. All

sensors should

have a green

light. Yellow

light indicates

that the sensor

requires

maintenance

soon. Red light

indicates

immediate

maintenance is

required.

Cleaning Pick Assembly Rollers

• Remove

Bill

Cassette

from Bill

Dispenser

to access

the Pick

Rollers

Remove Bill

Cassette

Inhaltsverzeichnis

Andere ICS Touch-Terminal Handbücher

ICS

ICS AMT-1 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung