ICT PRT-ZX1 Bedienungsanleitung

PRT-ZX1

Protege Single Input Expander

Installation Manual

The specifications and descriptions of products and services contained in this document were correct at the time

of printing. Integrated Control Technology Limited reserves the right to change specifications or withdraw

products without notice. No part of this document may be reproduced, photocopied, or transmitted in any form or

by any means (electronic or mechanical), for any purpose, without the express written permission of Integrated

Control Technology Limited. Designed and manufactured by Integrated Control Technology Limited, Protege® and

the Protege® Logo are registered trademarks of Integrated Control Technology Limited. All other brand or product

names are trademarks or registered trademarks of their respective holders.

Last Published: 16-Jun-22 11:43 AM

PRT-ZX1 | Protege Single Input Expander | Installation Manual 2

Contents

Protege Single Input Expander 4

Installation Requirements 5

DC Power & Encrypted Module Network 6

Installation Wiring 7

Input 8

Address Configuration 9

Technical Specifications 10

New Zealand and Australia 11

European Standards 12

UK Conformity Assessment Mark 14

FCC Compliance Statements 15

Industry Canada Statement 16

Disclaimer and Warranty 17

PRT-ZX1 | Protege Single Input Expander | Installation Manual 3

Protege Single Input Expander

The Protege Single Input Expander extends the number of inputs on the system by 1, allowing monitoring of a

wide range of EOL capable or open contact sensors for security and building automation purposes.

Flexible module network architecture allows large numbers of modules to be connected to the RS-485 module

network. Up to 250 modules can be connected to the Protege system in any combination to the network, over a

distance of up to 900M (3000ft). Further span can be achieved with the use of a network repeater module.

The current features of the input expander include:

⦁Secure encrypted RS-485 module communications

⦁1 input

⦁4 state input alarm using resistors to provide short, alarm, closed and tamper conditions

⦁Online and remote upgradable firmware

PRT-ZX1 | Protege Single Input Expander | Installation Manual 4

Installation Requirements

This equipment is to be installed in accordance with:

⦁The product installation instructions

⦁AS/NZS 2201.1 Intruder Alarm Systems

⦁The Local Authority Having Jurisdiction (AHJ)

PRT-ZX1 | Protege Single Input Expander | Installation Manual 5

DC Power & Encrypted Module Network

The expander incorporates encrypted RS-485 communications technology, and both module and network power

are supplied by the N+ and N- terminals.

NA NB

Network communications input

from the Controller or previous

module

N+ N-

Connection of the communications and DC supply should be performed according to the diagram shown above. It

is important that the N+ network communications power be 12VDC supplied from an independent battery backed

power supply unit capable of supplying the required voltage to all devices on the RS-485 network.

Warning:

⦁The 12V N+ and N- communication input must be supplied from only one point. Connections from more

than one 12V supply may cause failure or damage to the unit or the device supplying network power.

⦁The 330 ohm EOL (End of Line) resistor provided in the accessory bag must be inserted between the NA

and NB terminals of the first and last modules on the RS-485 network. These are the modules physically

located at the ends of the RS-485 network cabling.

End of Line Resistors:

330R 330R

First Module on RS-485 Network Last Module on RS-485 Network

Module

From

Module

NAN+ N- NB

PRT-ZX1 | Protege Single Input Expander | Installation Manual 6

Installation Wiring

The input expander comes supplied with a 5-pin expansion connector.

RED

BLACK

GREEN

WHITE

ORANGE

+12V

INPUT 1

Color Function

Red +12VDC

Black 0V

Green NA

White NB

Orange Input 1

PRT-ZX1 | Protege Single Input Expander | Installation Manual 7

Input

The input expander can monitor the state of 1 input using EOL monitored or dry contact devices such as magnetic

switches and PIR motion detectors. The input may be individually configured for normally opened and normally

closed configurations with or without EOL resistors for tamper and short condition monitoring.

When using an input with the EOL resistor configuration, the controller generates an alarm condition when the

state of an input changes between open and closed and generates a tamper alarm condition when a wire fault

(short circuit) or a cut wire (tampered) in the line occurs.

When using the EOL resistor configuration, the EOL resistor option must be enabled in the input programming so

that the tamper and short states can be monitored. For more information, refer to your Protege programming

reference manual.

EOL Resistor Input Configuration

ORANGEINPUT 1

0V BLACK

N.C Input Contact

N.C Tamper

Each input can use a different input configuration. To program a large number of inputs with the same

configuration use the multiple selection feature within the Protege software.

When using the 'No Resistor' configuration the controller only monitors the opened and closed state of the

connected input device, generating the alarm (open) and restore (closed/sealed) conditions.

No EOL Resistor Input Configuration

ORANGEINPUT 1

0V BLACK N.C Input Contact

PRT-ZX1 | Protege Single Input Expander | Installation Manual 8

Address Configuration

The module address is configured viaprogramming and will requireknowledge of the module serial number. The

serial number can be found on theidentification sticker on the product.

Refer to the Protege system controller installation manual foraddress programming details.

The controller has a set limit on the number of modules of each type that it can support. When adding and

configuring modules always refer to the Maximum Module Addresses table in the controller installation manual.

PRT-ZX1 | Protege Single Input Expander | Installation Manual 9

Technical Specifications

The following specifications are important and vital to the correct operation of this product. Failure to adhere to

the specifications will result in any warranty or guarantee that was provided becoming null and void.

Ordering Information

PRT-ZX1 Protege Single Input Expander

Power Supply

Operating Voltage 11 - 14VDC

Operating Current 20mA (Typical)

Communication

RS-485 Isolated Module Network

Inputs

Inputs 1

Dimensions

Dimensions (L x W x H) 7 x 18 x 20mm (0.28 x 0.71 x 0.79")

Net Weight Approx. 1g (0.04oz)

Gross Weight Variable packed qty.

Operating Conditions

Operating Temperature -10° to 55°C (14° to 131°F)

Humidity 0%-93% non-condensing, indoor use only (relative humidity)

Mean Time Between Failures

(MTBF) 784,316 hours (calculated using RFD 2000 (UTE C 80-810) Standard)

It is important that the unit is installed in a dry cool location that is not affected by humidity. Do not locate the unit

in air conditioning or a boiler room that can exceed the temperature or humidity specifications.

Integrated Control Technology continually strives to increase the performance of its products. As a result these

specifications may change without notice. We recommend consulting our website (www.ict.co) for the latest

documentation and product information.

PRT-ZX1 | Protege Single Input Expander | Installation Manual 10

Inhaltsverzeichnis

Andere ICT Extender Handbücher

ICT

ICT PRT-RDM2-DIN-485 Bedienungsanleitung

ICT

ICT PRT-ZX8-DIN Bedienungsanleitung

ICT

ICT Protege PRT-RDI2-PCB Bedienungsanleitung

ICT

ICT Protege PRT-PX8-DIN Bedienungsanleitung

ICT

ICT PRT-ADC4-DIN Bedienungsanleitung

ICT

ICT PRT-IO84-DIN Bedienungsanleitung

ICT

ICT PRT-HPX8-DIN Bedienungsanleitung

ICT

ICT PRT-ZX16-DIN Bedienungsanleitung

ICT

ICT PRT-HZX16-DIN Bedienungsanleitung

ICT

ICT PRT-F2F8-DIN Bedienungsanleitung

ICT

ICT PRT-ISO16-DIN Bedienungsanleitung

ICT

ICT PRT-HRDM-DIN Bedienungsanleitung

ICT

ICT Protege PRT-PX8-DIN Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung