IDEAL Imax Plus II F90 Benutzerhandbuch

users guide

Your Ideal users guide

See reverse for installation & servicing guide

ENGINEERED FOR PEACE OF MIND

When replacing any part on this appliance, use only spare parts that you can be

assured conform to the safety and performance specification that we require. Do not

use reconditioned or copy parts that have not been clearly authorised by Ideal Boilers.

plus II

Models F90, F140, F180

& F220, F270, F310

plus II

II - Users

Natural Gas only

PI No. 1312 BR 4912

Destination Countries: GB, IE

SAFETY

Current Gas Safety (Installation & Use) Regulations or Rules in

Force impose certain statutory obligations on gas users. This

appliance must be installed by a CORGI registered installer, or

in IE a competent person, in accordance with the above

regulations.

1. It is ESSENTIAL that the instructions in this booklet are

strictly followed, for safe, economical operation of the boiler.

CONTROLS OPERATION AND DISPLAY

2. Do not obstruct ventilation ducts, grilles or openings in the

boiler room, or the passage of combustion and ventilation

out to the boiler.

3. Do not store objects around or on the boiler, and keep

access clear at all times.

4. Flammable materials must not be placed in close proximity

to the boiler. Materials giving off vapours must not be stored

in the same room as the boiler.

5. A dust free environment should be maintained in the room

containing the boiler.

6. Do not turn off the boiler if it is to be left unattended in frosty

weather.

7. The boiler must not be operated without the casing correctly

fitted.

8. If it is known or suspected that a fault exists on the boiler

then is MUST NOT BE USED until the fault has been

corrected by a CORGI registered installer, or in IE a

competent person.

WARNING

This appliance MUST be efficiently earthed.

MAINTENANCE

The appliance should be serviced at least once a year by a

CORGI registered installer, or in IE a competent person.

CLEANING OUTER CASING

For normal cleaning simply dust with a dry cloth. To remove

stubborn marks and stains use a damp cloth and mild

detergent.

DO NOT use abrasive cleaning materials.

1243

576

STORE

MODE

RESET

STEP

ResetDisplay Mode

Step Store+ -

On/Off switch

Reset buttons for the

different modules

Operation and indications on the display (examplewith 7modules)

Pressure

gauge

ima 5784

All CORGI registered installers carry a CORGI ID card, and have a registration number. Both should be recorded in

your Benchmark Log Book. You can check your installer by calling CORGI direct on 01563 72300

II - Users

During normal operation of the imax plus II, the status of the appliance can be determined from the display.

The first 2 digits show the status of the boiler, the last 2 digits display the current flow temperature, except with

status 1, 2 or 5 when the number indicates the burner module about to start.

All other displays refer to error messages, see Frames 46 and 47 in the Installation & Servicing Instructions for

details.

On/Off Switch

The on/off switch turns the mains power on/off within the

boiler. It does not isolate the boiler from the mains.

Therefore it is important that the boiler is isolated at the

external mains connection point before removing any casing

panels.

Module and Reset Buttons

If a module locks out then its Reset Button becomes

illuminated. To reset the module you must hold down this

button whilst pressing the reset key.

Mode Key

The default mode of the boiler is standby. By pressing the

mode key it is possible to change the mode.

By pressing the mode key once, PARA mode (abbreviation for

parameter) is displayed. In this mode it is possible to

change the settings of the boiler control module.

By pressing the mode key again, DATA mode is displayed. In

this mode it is possible to read information on the operation

of the boiler.

Step Key

Having selected the mode required the step key is used to

move through the options available to be changed or checked.

+/- Key

By pressing the top or bottom of this key it is possible to

increase or decrease a value.

Store Key

After a setting has been changed, pressing the store button

holds this new value in the memory. This key is also used to

move through some options available as sub menus within

DATA mode.

CONTROLS OPERATION AND DISPLAY CONTD

Display Status Boiler Status

0_xx Standby: no heat request

1_xx The fan of the burner to be ignited is running in prepurge

2_xx The safety time of the burner to be ignited is operative

3_xx Burner 'on' in CH mode

4_xx Burner 'on' in DHW mode

5_xx The fan of the burner to be ignited is being set to start speed.

6_xx Burner 'off' in CH mode because a set value has been reached.

7_xx Pump overrun in CH mode.

8_xx Pump overrun in DHW mode.

9_xx Burner 'off' in DHW mode because a set value has been reached.

II - Users

PARA AND DATA ACCESS

Shows the value of the displayed parameter

Shows the number of the parameter displayed (from 1 to 9 and from A to N)

The User has

access to these

three parameters

only (see Frame 28)

By pressing store

By pressing

mode

By pressing step

By pressing Step,

By pressing step

STEP

STORE

MODE

RESET

As above

it selects :

- parameters

- data (all/sin gle)

- test (all/s in gle)

ch oos es

the mo de

It d isp lays when

in DATA mode.

It st or es when

in PARA mode.

+/- :

it in cr eases

or decr eases

the displ ayed

va lu e

Reset

the boile r

e parameter number is not displayed.

By pressing

step

By pressing

mode

By pressing

mode

By pressing step

By pressing

store

By pressing

store

By pressing

store

By pressing

store

By pressing

store

By pressing

store

By pressing

store

By pressing

store

1. 60

X XXX

2. 0 1

1. 501. 50

3. 80

. XX

. XXX

XXXX

figure is stored

after flashing once

By pressing store the

change to

Status Number see Table

Flow Temperature or Burner under Ignition

= Stand-by mode Dispaly

ima7255

DATA

relevant

total

appliance

II - Users

CONTROL OF WATER TEMPERATURE AND SYSTEM TYPES

By pressing the mode key once, PARA mode (abbreviation for

parameter) is displayed. In this mode it is possible to change

the settings of the boiler control module.

DHW Storage Temperature Setpoint (degC)

Press Display Description

P A R A

Press Display

Parameters accessible to user

MODE

STEP

Lower

Limit

Upper

Limit

Factory

Setting

40 65 60

2. 0 1

STEP

CH and DHW Options

00 = CH & DHW are both off

01 = CH is on, DHW is off

02 = CH is on, DHW is off, System pump runs continuously

11 = CH & DHW are both on

12 = CH & DHW are both on, System pump runs continuously

1. 6 0

Maximum CH Flow Temperature Setpoint (degC)

STEP

30 90 80

3. 8 0

DATA MODE

By pressing the mode key twice, DATA mode is displayed. In this mode it is possible to read information on the operation of the boiler.

Press Display Description Unit

Global flow temperature ºC

Global return temperature ºC

DHW temperature ºC

Outside temperature ºC

N/A ºC

Flow temperature set point ºC

Fan speed set point rpm

Output calculated in % (100% per module) %

Data relevant to the whole boiler.

STORE

T O T

1 . X X

2 . X X

3 . X X

4 . X X

5 . X X

6 . X X

X X X X

STEP

8 . X X

D A T A

Press Display

MODE

Twice

II - Users

TO LIGHT THE BOILER

1. Switch on the electricity supply to the boiler and check that all

external controls e.g. programmer, room thermostats, etc.

are calling for heat.

2. Set the On/Off switch on the boiler to ON.

The boiler will commence the ignition sequence, supplying

heat to the system when required.

TO SHUT DOWN THE BOILER

1. For short periods

Set the parameter 2 to '00'. Note. the boiler will still fire in

frost protection mode.

2. For longer periods

Set to OFF the on/Off switch on the boiler. Isolate the mains

supply to the boiler. For longer periods the entire system

should be drained, including the domestic hot water supply.

TO RELIGHT THE BOILER

1. After Short Periods

Reset parameter 2 to the desired setting.

2. After Long Periods

The system should be re-filled, commissioned and tested by

a CORGI registered installer, or in IE a competence person,

in accordance with the Installation & Servicing Instructions.

FROST PROTECTION

The imax plus II boiler has built into its control system the facility

to protect the boiler only against freezing.

Note.

This may not protect remote parts of the system, in which case a

separate frost thermostat should be fitted.

BOILER LOCKOUTS

When a burner module locks out, the corresponding red reset

button illuminates on the fascia. If the entire boiler locks out, an

error message is displayed (see Frames 46 & 47 of Installation

& Servicing Instructions).

To reset the boiler, press and hold the illuminated red reset

buttons of each failed module and press the reset button on the

fascia.

Note.

If it is known or suspected that a fault exists on the boiler then it

MUST NOT BE USED until the fault has been corrected by a

CORGI registered installer, or in IE a competent person.

CONDENSATE DRAIN

The condensate drain must not be modified or blocked.

Blockage of the condensate drain, caused by debris or freezing,

can cause automatic shutdown of the boiler or leakage from the

condensate trap mounted on the bottom of the boiler.

If freezing is suspected and the pipe run is accessible an

attempt may be made to free the obstruction by pouring hot

water over the exposed pipe and clearing any blockage from the

end of the pipe. If this fails to remedy the problem the

assistance of a CORGI registered installer, or in IE a competent

person, should be sought.

ESCAPE OF GAS

Should a gas leak or fault be suspected contact your local gas

supplier without delay.

Do NOT search for gas leaks with a naked flame.

II - Users 7

Ideal Boilers, P.O. Box 103, National Ave, Kingston Upon Hull, HU5 4JN. Tel.

01482 492251 Fax. 01482 448858. Registration No. London 322 137.

Ideal Stelrad Group pursues a policy of continuing improvement in the design and performance

of its products. The right is therefore reserved to vary specification without notice.

Ideal Consumer Helpline

Tel: 01482 498376

www.idealboilers.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IDEAL Kessel Handbücher

IDEAL

IDEAL Classic LX RS 230 Versionshinweis

IDEAL

IDEAL Vogue Combi c26 Bedienungsanleitung

IDEAL

IDEAL F400 Bedienungsanleitung

IDEAL

IDEAL Henrad SEC 80FF Benutzerhandbuch

IDEAL

IDEAL Concord CXA 40/H Benutzerhandbuch

IDEAL

IDEAL Viceroy GT Series Leitfaden

IDEAL

IDEAL 36 Bedienungsanleitung

IDEAL

IDEAL EXALT COMBI Bedienungsanleitung

IDEAL

IDEAL IMAX XTRA E80 Bedienungsanleitung

IDEAL

IDEAL Mexico Super 40 FF Bedienungsanleitung

IDEAL

IDEAL Exalt FSB 110 Benutzerhandbuch

IDEAL

IDEAL MINI C24 Bedienungsanleitung

IDEAL

IDEAL Evomax 30 Bedienungsanleitung

IDEAL

IDEAL m30100 Bedienungsanleitung

IDEAL

IDEAL evojet Bedienungsanleitung

IDEAL

IDEAL HE9 Bedienungsanleitung

IDEAL

IDEAL he15 Bedienungsanleitung

IDEAL

IDEAL SUPER PLUS 200/S Bedienungsanleitung

IDEAL

IDEAL SUPER PLUS 200/S Bedienungsanleitung

IDEAL

IDEAL LOGIC+ Combi 24 Bedienungsanleitung

IDEAL

IDEAL Vogue Combi c26 Bedienungsanleitung

IDEAL

IDEAL Response SE Beilage

IDEAL

IDEAL MINI C24 Bedienungsanleitung

IDEAL

IDEAL Logic+ SYSTEM 15 Bedienungsanleitung

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung