IDEAL 61-603 Bedienungsanleitung

IDEAL INDUSTRIES, INC.

TECHNICAL MANUAL

MODEL: 61-603

The Service Information provides the following information:

•Precautions and safety information

• Specifications

• Performance test procedure

• Calibration and calibration adjustment procedure

• Basic maintenance (replacing the battery and fuses)

Form number: TM61603

Revision: 3. Date: Feb 2002

Form number TM61603 Rev 3 February 2002

TABLE OF CONTENTS

Title Page

Introduction 1

Precautions and Safety Information 1

Safety Information 1

Specifications 2

General Specification 2

Voltage Specifications 2

Current Specifications 2

Resistance Specifications 2

Diode Specifications 2

Battery Check Specifications 2

Performance Verification 3

Calibration 4

Printed Circuit Board 4

Replacing the Battery 5

Replacing Fuses 5

Form number TM61603 Rev 3 February 2002

Page 1

Introduction

Warning

To avoid shock or injury, do not perform the verification tests or calibration

procedures described in this manual unless you are qualified to do so.

The information provided in this document is for the use of qualified personnel only.

Caution

The 61-603 contains parts that can be damaged by static discharge.

Follow the standard practices for handling static sensitive devices.

For additional information about IDEAL INDUSTRIES, INC. and its products,

and services, visit IDEAL INDUSTRIES, INC. web site at:

www.idealindustries.com

SAFETY

Review the following safety precautions to avoid injury and prevent damage to this product or any

products connected to it. To avoid potential hazards, use the product only as specified.

CAUTION.

These statements identify conditions or practices that could result in damage to the equipment or other

property.

WARNING.

These statements identify conditions or practices that could result in personal injury or loss of life.

Specific precautions

Use proper Fuse. To avoid fire hazard, use only the fuse type and rating specified for this product.

Do not operate without covers. To avoid personal injury, do not apply any voltage or current to the

product without the covers in place.

Electric overload. Never apply a voltage to a connector on the product that is outside the range specified

for that connector.

Avoid electric shock. To avoid injury or loss of life, do not connect or disconnect probes or test leads

while they are connected to a voltage source.

Do not operate in wet/damp conditions. To avoid electric shock, do not operate this product in wet or

damp conditions.

Form number TM61603 Rev 3 February 2002

Page 2

General specifications

Characteristics Description

Display 3½ Digit LCD display

Display Count 2000 count, maximum reading 1999

Overrange Indication “1___” most significant digit

Sampling Rate 3 time/second

Operating Environment:

Relative Humidity

0°C to 40°C (32°F to 104°F)

80% for temperatures up to 31°C

Decreasing linearly to 50% at 40°C

Storage Environment: -20°C to 60°C (-4°F to 140°F) at <80% relative

humidity

Power source: 9V Battery (NEDA 1604)

Battery Live: 150 hours typical (alkaline)

Low Battery Indicator: symbol indicates low battery voltage

mA protection Fuse 500mA, 250V fast acting fuse

Dimensions 5.0” H X 2.8” W X 1.4” D

128mmH X 72mmW X 36mmD

Weight: Approximately 7.0 oz. or 200g including battery

RANGES and ACCURACY SPECIFICATION

Function Setting Ranges Accuracy

AC Voltage 200.0/500 V

1.0% ± 4 digits

DC Voltage 2.000/20.00/200.0/1000 V 0.5% ± 2 digits

AC Current n/a n/a

DC Current 2.000mA/20.00mA/200.0mA/

10.00A

1.0% ± 1 digit

2.0% ± 2 digits

Resistance 200.0Ω

2.000K/20.00K/200.0K

2.000MΩ

1.2% ± 3 digits

1.0% ± 1 digit

1.5% ± 2 digits

Diode Check DCV 2V @ 1.0 mA ± 0.6 mA

AC Converter: Average responding, RMS Calibrated to Sine Wave

Overload Protection: AC and DC Voltage: 1100 VDC or 500VAC RMS for no more than one minute.

Resistance: 250VDC or AC RMS

10A input, un-fused

mA input, 500mA at 250V fast acting fuse.

Form number TM61603 Rev 3 February 2002

Page 3

PERFORMANCE VERIFICAITONS

Perform the following analysis, if the meter conforms to the limits listed in Table 1 the meter is functioning

correctly. If the meter does not conform to any of the listed limits the calibration procedure must be

performed.

Performance Verification Preparation

1. Turn on the Calibrator, allow calibrator to warm up. Temperature Stabilization

should be reached after 30 minutes.

2. Remove battery cover and using a calibrated meter to ensure the battery measures a minimum of 7.5V

DC. If the battery measures under 7.5V DC, replace the battery before beginning the performance test.

3. Input the values listed in Table 1

Table 1 Performance Verification

Function Setting

Input

Low Limit

High Limit

ACV 200 190V AC@ 60Hz 187.7 192.3

ACV 500 400V AC@ 60Hz 392 408

DCV 2 1.900V DC 1.888 1.911

DCV 20 19.00V DC 18.88 19.11

DCV 200 190.0V DC 188.8 191.1

DCV 900 900V DC 893 906

DCmA 2m 1.900 mA DC 1.879 1.921

DCmA 20m 19.00 mA DC 18.79 19.21

DCmA 200m 190.0 mA DC 187.9 192.1

DC A 10 9.00 A DC 8.80 9.20

Ω200 100.0 98.7 101.3

Ω2K 1.000K .992 1.008

Ω20K 10.00K 9.92 10.08

Ω200K 100.0K 99.2 100.8

Ω2M 1.000M .988 1.012

Form number TM61603 Rev 3 February 2002

Page 4

CALIBRATION

Calibration Preparation

1. Turn on the Calibrator, allow calibrator to warm up. Temperature Stabilization

should be reached after 30 minutes.

2. Disconnect the test leads and turn the range switch to “OFF”.

3. Remove the screw holding the bottom case cover, just above the battery cover.

4. The case bottom is secured to the case top by two internal snaps (at the LCD end).

lift up on the battery end until the case un-snaps.

5. Using a calibrated meter ensure the battery measures a minimum of 7.5V DC.

If the battery measures under 7.5V DC, replace the battery.

Calibration Procedure

It is recommended that all IDEAL meters undergo the following calibration procedure on

an annual basis.

Volts DC Calibration

1. Set the function / range to 2V DC

2. Connect the calibrator to the VΩand COM inputs on the meter.

3. Output 1.900V DC.

Adjust R47 unit the display reads 1.900V

Note: This is the only adjustment required for the 61-603. Calibration is complete.

61-603 main printed circuit board (refer to Figure 1)

Form number TM61603 Rev 3 February 2002

Page 5

Battery Replacement (refer to Figure 2)

1. Disconnect the test leads from any circuit under test and turn off meter.

2. Slide off the back case battery cover

3. Remove battery from compartment and unsnap the battery connector.

4. Install new 9V battery (NEDA #1604). An alkaline type is recommended.

5. Install new battery into compartment using care not to pinch or bind battery leads.

6. Slide battery cover along glide until cover snaps into bottom case.

Insure that cover aligned with snaps at bottom of the case.

Replacing Fuse (refer to Figure 3)

1. Disconnect the test leads and turn the range switch to “OFF”.

2. Remove the screw holding the bottom case cover, just above the battery cover.

3. The case bottom is secured to the case top by two internal snaps (at the LCD end).

lift up on the battery end until the case un-snaps.

4. Remove the defective fuse and replace with a 500mA, 250V Fast Acting fuse.

IDEAL #F-7 Type is recommended.

5. Replace bottom cover insuring that case is secured at the top by the internal snaps and

replace screw.

Form number TM61603 Rev 3 February 2002

Inhaltsverzeichnis

Andere IDEAL Multimeter Handbücher

IDEAL

IDEAL 61-340 Bedienungsanleitung

IDEAL

IDEAL ND-5499 Bedienungsanleitung

IDEAL

IDEAL 61-614 Bedienungsanleitung

IDEAL

IDEAL 61-327 Gebrauchs- und Pflegehandbuch

IDEAL

IDEAL 61-310 Bedienungsanleitung

IDEAL

IDEAL 61-764 Bedienungsanleitung

IDEAL

IDEAL ND 2352-1 Bedienungsanleitung

IDEAL

IDEAL ND 2385-1 Bedienungsanleitung

IDEAL

IDEAL Resi-Pro 310 Series Bedienungsanleitung

IDEAL

IDEAL ND 3405-1 Bedienungsanleitung

IDEAL

IDEAL ND 1075-2 Bedienungsanleitung

IDEAL

IDEAL 61-497 Bedienungsanleitung

IDEAL

IDEAL ND 2350-1 Bedienungsanleitung

IDEAL

IDEAL 61-340 Bedienungsanleitung

IDEAL

IDEAL 61-497 Bedienungsanleitung

IDEAL

IDEAL 61-357 Gebrauchs- und Pflegehandbuch

IDEAL

IDEAL 602 Bedienungsanleitung

IDEAL

IDEAL SecuriTEST Bedienungsanleitung

IDEAL

IDEAL 61-681 Bedienungsanleitung

IDEAL

IDEAL 61-354 (TRMS) Bedienungsanleitung

IDEAL

IDEAL ND 2365-1 Bedienungsanleitung

IDEAL

IDEAL ND 2366-1 Bedienungsanleitung

IDEAL

IDEAL 61-797 Bedienungsanleitung

IDEAL

IDEAL ND 4950-3 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung