IDEC LONWORKS Bedienungsanleitung

LONWORKS

Communication Module

User's Manual

FL9Y-B695

LONWORKS® Communication Module User’s Manual i

Indicates that death or severe

bodily injury may occur, if the

corresponding safety measures

are not taken.

Safety Notices

DANGER

WARNING

CAUTION

WARNING

Indicates that death, severe bodily

injury or substantial material damage

will occur, if the corresponding safety

measures are not taken.

With the warning triangle, this

indicates that minor bodily

injury may occur, if the

corresponding safety measures

are not taken.

Without the warning triangle,

this indicates that material

damage may occur, if the

corresponding safety measures

are not taken.

This indicates that an undesirable

result or condition may occur, if the

corresponding instructions are not

observed.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

LONWORKS® Communication Module User’s Manual ii

You may not transfer or duplicate this document or utilize or reveal its contents,

unless expressly authorized in writing. In the case of a violation, you will be obliged

granted or that a utility model is registered.

Disclaimer of liability:

We have checked that the contents of this document correctly describe the

associated hardware and software. Nonetheless, it is impossible to exclude the

possibility of deviations and therefore we cannot guarantee that there are no errors

in this document. The information in this document is checked regularly and any

necessary corrections are then made in the next release issued. We are of course

thankful for any suggestions for improvements.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

LONWORKS® Communication Module User’s Manual iii

Table of Contents

1. Getting to know LONWORKS® Communication Module..... 1-1

1.1 What is LONWORKS® Communication Module ? ................... 1-1

1.2 The construction of the LONWORKS® Communication Module1-2

2. Mounting and wiring the LONWORKS® Communication Module…2-1

2.1 General guidelines .................................................................... 2-1

2.2 Wiring the LONWORKS® Communication Module .................. 2-3

2.2.1 Connecting the power supply...................................................2-4

2.2.2 Connecting the LON.................................................................2-5

3. Putting the LONWORKS® Communication Module into operation 3-1

3.1 Step-by-step.............................................................................. 3-1

3.2 The LONWORKS® Communication Module - operational status3-2

3.3 Behavior in case of a fault......................................................... 3-3

4. Supported functions.................................................................... 4-1

4.1 Virtual inputs / outputs............................................................... 4-1

4.2 Available network variables....................................................... 4-3

4.3 LON configuration parameters .................................................. 4-5

4.4 Inputs / Outputs – special considerations.................................. 4-6

4.5 Alias table entries...................................................................... 4-6

5. LONWORKS® Communication Module - Specifications ....... 5-1

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

LONWORKS® Communication Module User’s Manual 1-1

1. Getting to know

LONWORKS® Communication Module

1.1 What is LONWORKS® Communication

Module ?

The Local Operating Network (LONWORKS® Communication

Module) communications module is an interface for

connecting IDEC SmartRelay onto a LON network.

The IDEC SmartRelay communications module has been

implemented as a Slave module for the IDEC SmartRelay

control module.

The module supports communication between the IDEC

SmartRelay Master and external LON devices via a LON.

The LONWORKS® Communication Module is a bus station on

the LON and allows the IDEC SmartRelay to communicate

with other LON devices.

What are the capabilities of the LONWORKS®

Communication Module ?

The LONWORKS® Communication Module presents the

current states of the LON stations to the IDEC SmartRelay,

which is thus able to use its logical functions and timers to

join them together. In the process, the LON signals can also

be combined with the signals of the local IDEC SmartRelay

inputs and outputs. The LONWORKS® Communication

Module then transmits every change of the output signal via

the LON.

The combination of IDEC SmartRelay and LONWORKS®

Communication Module gives the user a decentralized

controller functionality for the LON with the capability of

setting or changing parameters or operations quickly, simply

and without a programming device.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

LONWORKS® Communication Module User’s Manual 1-2

1.2 The construction of the LONWORKS®

Communication Module

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

LONWORKS® Communication Module User’s Manual 1-3

1. Power supply

2. Bus lock slider, interface to the IDEC SmartRelay

3. The RUN/STOP LED for IDEC SmartRelay

communication

4. The SERVICE LED

5. Input - LON connection

6. Expansion interface to the IDEC SmartRelay

7. Mechanical coding - pin

8. Service button

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

LONWORKS® Communication Module User’s Manual 2-1

2. Mounting and wiring the LONWORKS®

Communication Module

2.1 General guidelines

The following guidelines should be observed when mounting

wiring your LONWORKS® Communication Module:

- When wiring the LONWORKS® Communication Module,

make certain that you follow all of the applicable and

legally binding standards. Observe all of the relevant

national and regional regulations when installing and

operating the device. Check with the local authorities

regarding the standards and regulations that must be

observed in your special case.

- Make certain that the device is de-energized.

- Use only approved bus cables.

- Make certain that the specified cable lengths are used and

that the correct terminating resistors are installed properly.

- The LONWORKS® Communication Module must always

be installed as the last module on the right of the IDEC

SmartRelay, since you may not install other expansion

modules onto the LONWORKS® Communication Module.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

LONWORKS® Communication Module User’s Manual 2-2

Please notice:

- The LONWORKS® Communication Module must have its

own power supply (24 V AC/DC).

NOTE

This module may only be mounted and wired by qualified

personnel, who know and observe the generally applicable

guidelines and applicable regulations and standards.

Observe the assembly and disassembly instructions in the

IDEC SmartRelay manual.

WARNING

The expansion module may only inserted or removed when

the power is off.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

LONWORKS® Communication Module User’s Manual 2-3

2.2 Wiring the LONWORKS® Communication

Module

To wire the LONWORKS® Communication Module, use a

screwdriver with 3 mm wide blade.

- You do not need to use wire end ferrules when clamping

the wires.

NOTE

After the installation, the terminals must be covered. To

protect personnel against unintentional contact with the

portions of the LONWORKS® Communication Module that

are conducting electricity, the appropriate national and local

standards must be observed.

The LONWORKS® Communication Module is a double-

insulated switching device.

A protective grounding conductor is not necessary.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Inhaltsverzeichnis

Andere IDEC Steuereinheit Handbücher

IDEC

IDEC HR6S-DN Bedienungsanleitung

IDEC

IDEC MicroSmart pentra FC5A-C10R2 Bedienungsanleitung

IDEC

IDEC HR6S-S Bedienungsanleitung

IDEC

IDEC HR6S Series Bedienungsanleitung

IDEC

IDEC HR1S-ATE Bedienungsanleitung

IDEC

IDEC MICROSmart FC4A-SX5ES1E Bedienungsanleitung

IDEC

IDEC MicroSmart pentra FC5A-D12K1E Bedienungsanleitung

IDEC

IDEC MicroSmart Series Bedienungsanleitung

IDEC

IDEC SmartRelay Series Bedienungsanleitung

IDEC

IDEC FC5A-F2M2 Bedienungsanleitung

IDEC

IDEC MICROSmart FC5A Series Bedienungsanleitung

IDEC

IDEC MICROSmart FC6A-C16K1CE Gebrauchs- und Pflegehandbuch

IDEC

IDEC SmartRelay FL1D Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung