Idex Semrock FL CUBE EC P and C Bedienungsanleitung

Zeiss ZHE Cube Assembly Procedure

2/12

Step

Action

1.1

Disassemble Cube

1.1.1

The cube assembly has two filter retainer rings; one is located on the Exciter side

and one is on the Emitter side as shown below.

1.1.2

Remove both filter retainer rings from the cube assembly.

1.1.2.1

The supplied retaining rings for the ZHE cube are installed shoulder side inward.

Remove the rings by gently grasping the slots with your finger tips. Applying even

pressure to the retaining ring slots, turn the ring outward (counterclockwise) to

remove from the cube assembly.

Emitter Retaining Ring

Exciter Retaining Ring

Slots

Zeiss ZHE Cube Assembly Procedure

3/12

Step

Action

1.1.2.2

Note that there are two distinctly different sides to the retainer rings. One is the

“flat” Shoulder Side and one is the Open Side.

The Open Side ALWAYS faces into the cube assembly and is tightened against the

installed filter. The Shoulder Side faces outward. The two sides are shown below for

reference.

Open Side Shoulder Side

Zeiss ZHE Cube Assembly Procedure

4/12

Step

Action

1.2

Install the Semrock Filter Set

1.2.1

The diagram below illustrates a cross section of the Zeiss ZHE cube for use in

orienting and installing the Exciter, Dichroic and Emitter filters into the cube

assembly. The cross section is for reference only to illustrate filter position and

orientation.

Filter Positions

The Emitter is located at the top of the cube assembly. Notice it is mounted at a slight angle.

The Exciter is located at the left side and the Dichroic is

mounted diagonally at the center of the cube and shares the

Emitter half of the assembly.

Filter Orientation

The filters are oriented in the assembly as follows:

The Exciter is mounted with its arrow pointing inward.

The Dichroic reflective side is mounted facing the Exciter

The Emitter is mounted with its arrow pointing outward.

Light passes through the cube in the direction of the arrows.

The arrows point toward the Anti-Reflective coatings on the

Emitter and Exciter filters.

Note: The Dichroic Reflective coating must face the Exciter as

shown in the cross section diagram.

Step

Action

Dichroic

Emitter

Exciter

ZHE Filter Positions

Dichroic reflective coating faces the Exciter

Zeiss ZHE Cube Assembly Procedure

5/12

Step

Action

1.2.2

Remove the two Flat Head screws to separate the cube halves. Set the screws aside

for reassembly later.

1.2.3

Separate the cube halves to prepare for assembly of the Semrock filter set.

Note that there are two prongs used to locate and hinge the cube housing and a metal

spring clip that is used to position and secure the Dichroic filter during assembly.

Remove

Screws

Hinge

Spring Clip

Zeiss ZHE Cube Assembly Procedure

6/12

Step

Action

1.2.4

Assemble the Dichroic/Emitter half of the cube first. The Dichroic is positioned

over the spring clip between the upright flanges at either end of the spring. Note that

the clip locating tab is inserted into the notch at the side of the cube assembly.

Note: Ensure the spring clip flanges face UPWARD.

1.2.5

Reflective “Coated Side”: The filter edge is concealed by the reflective coating and

appears colored all the way to the edge.

Anti-Reflective “Uncoated Side”: The filter edge appears uncolored.

Reflective Side Anti-Reflective Side

Locating Tab

Dichroic Mounting Area

Flanges face Up

Zeiss ZHE Cube Assembly Procedure

7/12

Step

Action

1.2.6

Install the Dichroic over the spring clip with the Reflective coated side facing up.

Center the filter within the mounting area between the mounting flanges. Once the

Dichroic is centered, insert the prongs of the hinge into the Exciter half of the cube

and carefully fold the cube together keeping the Dichroic centered in its mounting

area. Apply gentle pressure to the cube halves during assembly to retain the Dichroic

within the flanges of the spring clip.

Note: The cube halves should fit together flush and without interference at either

mounting surface.

Note: DO NOT rest the cube assembly on the Dichroic filter during assembly.

1.2.7

Check the alignment of the Dichroic and spring clip through the slots on the cube

side. Ensure the spring clip locating tab is flush within the slotted opening and the

Dichroic is aligned within the spring clip flanges. The spring clip should not be

visible in the screw holes or interfere with screw placement.

Carefully fold the cube together while

keeping the Dichroic centered in the spring

clip.

Zeiss ZHE Cube Assembly Procedure

8/12

Step

Action

1.2.8

Fasten the cube halves together using the two flat head screws removed previously.

Alternately tighten the screws until they are snug. Once snug, further tighten ¼ turn.

1.2.9

Orient the Emitter with the arrow pointing away from the cube as shown below.

Zeiss ZHE Cube Assembly Procedure

9/12

Step

Action

1.2.10

Place the filter inside the Emitter mounting area with the arrow pointing up.

Note that the filter shoulder side faces outward.

1.2.11

Insert the filter retaining ring open side into the Emitter mounting area of the cube.

Note that the cube threads are at an angle. This will require careful installation of the

retaining ring to avoid cross threading.

Using your fingers, carefully turn the ring while observing its position in the threads.

Keep the ring level across the threaded area while allowing the ring to tilt as it

threads inward. If the ring will not turn, it is not threaded properly – slowly turn the

ring out and try again. Do not force thread the ring as it will turn freely if oriented

correctly. Turn the ring inward until it starts to resist finger tightening.

Note the angle of the retaining ring threads in the photo below.

Zeiss ZHE Cube Assembly Procedure

10/12

Step

Action

1.2.12

Locate the the THORLABS SPX602 Spanner Wrench. The spanner wrench blades

are shown below.

1.2.13

Insert the spanner wrench blades into the slots of the Emitter retaining ring. Tighten

the ring snug against the Emitter filter. Once snug, tighten slightly further to secure.

Spanner wrench blades

Inhaltsverzeichnis

Andere Idex Kamerazubehör Handbücher

Idex

Idex Semrock U-MF2 Bedienungsanleitung

Beliebte Kamerazubehör Handbücher anderer Marken

Viltrox

Viltrox EF-NEX Montageanleitung

Calumet

Calumet 7100 Series CK7114 Bedienungsanleitung

Ropox

Ropox 4Single Series Bedienungsanleitung

Cambo

Cambo Wide DS Digital Series Betriebsanleitung

Samsung

Samsung SHG-120 Bedienungsanleitung

Ryobi

Ryobi BPL-1820 Bedienungsanleitung

Aegis

Aegis ABL-36020P Bedienungsanleitung

Fantasea

Fantasea EyeGrabber F Series Bedienungsanleitung

Honeywell

Honeywell HDZ20HD Bedienungsanleitung

EGO

EGO BA1400T Bedienungsanleitung

Sima

Sima SRW-62 Bedienungsanleitung

Shape

Shape A7SSMKIT Bedienungsanleitung

Slide Kamera

Slide Kamera HST-2 Bedienungsanleitung

Power works

Power works 2902613 Bedienungsanleitung

SES

SES SE-2047-2 Bedienungsanleitung

Starlite

Starlite OctoDome nxt Bedienungsanleitung

Custom Brackets

Custom Brackets Digital PRO-M Bedienungsanleitung

Vivo

Vivo MOUNT-LT01C Bedienungsanleitung