Idex Pulseafeeder MicroVision Boiler Bedienungsanleitung

MicroVision Boiler

MICROPROCESSOR – BASED

WATER TREATMENT

CONTROLLER

Installation Operation Manual

72-910-24 Revision H

TABLE OF CONTENTS

INTRODUCTION..............................................................................................................................3

MICROVISION FEATURES.............................................................................................................3

Output Relays ............................................................................................................................3

Drum Levels ............................................................................................................................3

4-20mA Output .........................................................................................................................4

Water Meter ............................................................................................................................4

Alarm Relay ............................................................................................................................4

INSTALLATION ............................................................................................................................5

Location ...................................................................................................................................6

Mounting Hardware....................................................................................................................6

Sensor Installation ...................................................................................................................7

TYPICAL INSTALLATION ..............................................................................................................8

IMPORTANT SYMBOL INFORMATION .........................................................................................9

ELECTRICAL WIRING ....................................................................................................................9

RELAY BOARD CONNECTIONS .................................................................................................10

Conduit Models .......................................................................................................................10

LOW VOLTAGE CONNECTIONS ................................................................................................11

Sensor (probe) Connection Input ..........................................................................................11

Water Meter Input ............................................................................................................11

Drum Level Input ................................................................................................................ 11

4-20mA Output .......................................................................................................................11

Water Meter ..........................................................................................................................11

Alarm Relay ................................................................................................................ 11

FRONT PANEL DESCRIPTION ................................................................................................... 12

Keypad Operation .................................................................................................................13

CONTROLLER PROGRAMMING ................................................................................................13

Menu Tree ..............................................................................................................................13

Menu Navigation ....................................................................................................................14

Home Screen .......................................................................................................................14

Main Menu ......................................................................................................................... 14

Configure Menu .......................................................................................................................15

HOA Relay Output Menu.........................................................................................................16

Inputs Menu ..........................................................................................................................17

Drum Level Menu .................................................................................................................17

Display Dampener Settings ................................................................................................18

Password Setting .................................................................................................................19

Troubleshoot Screen ...............................................................................................................19

Factory Reset Function ...........................................................................................................20

Settings Menu ............................................................................................................................20

Blowdown Menu.......................................................................................................................21

4-20mA ..............................................................................................................................21

Calibration Menu......................................................................................................................23

Timers Menu............................................................................................................................24

FACTORY DEFAULT VALUES/ USER SETTINGS .....................................................................27

SATURATED STEAM TABLE ...................................................................................................27

TROUBLESHOOTING GUIDE ...................................................................................................28

MAINTENANCE ..........................................................................................................................29

SPECIFICATIONS .......................................................................................................................29

GLOSSARY .................................................................................................................................30

FACTORY SERVICE POLICY.......................................................................................................31

WARRANTY .................................................................................................................................32

72-910-24 Revision H

INTRODUCTION

The MicroVision microprocessor-based Boiler controller has been designed to monitor and control

Total Dissolved Solids (TDS) in terms of electrical conductivity measured in micro Siemens per

centimeter (uS/cm). A set point of the desired conductivity is entered into the controller through the

front panel. As this limit is exceeded, a blowdown valve is opened via an onboard control relay on

either a timed, continuous or sample and hold basis. The system’s water, with higher concentrations

of TDS, is drained from the system resulting in feed water being added, reducing the concentration

of TDS in the Boiler.

The MicroVision has five (5) output relays assigned as follows:

Relay 1 – Blowdown

Relay 2 – Timer #1

Relay 3 – Timer #2

Relay 4 – Timer #3

Relay 5 – Alarm or Timer #4 (normally open dry contact)

MICROVISION FEATURES

Output Relays

The control of the four HANDS – OFF – AUTO (HOA) output relays can be controlled using the HOA

menu.

RELAY STATUS

LED COLOR

ON (FORCED ON FOR 5 MIN.)

AMBER

OFF

RED

AUTOMATIC ‘ON’

GREEN

AUTOMATIC ‘OFF’

OFF

Inputs:

The MicroVision has 5 digital inputs that can be programmed as follows:

Programmable Inputs

Input 1

Input 2

Input 3

Input 4

Input 5

Drum Level

X (Timer 2)

X (Timer 3)

X (Timer 4)

X (Timer5)

Contacting Head Water Meter

Hall Effect Water Meter

Interlock

Drum Levels

When an input is defined as a drum level it is linked to the corresponding relay output. For example, if

input #2 is set as drum level, it will be linked to relay two and may be set by the user to either

deactivate the relay, or only to activate an alarm.

72-910-24 Revision H

Interlock

MicroVision has a dry contact interlock option for input number 5 that will de-activate all of the control

output relays upon an interlock condition indication. The interlock input requires that an auxiliary

relay (not supplied) is installed across the boiler operation controls to produce a dry contact closure

when the boiler is online and an open circuit when the boiler is offline. The Alarm message “Interlock

on” will flash on the screen when the controllers interlock feature is on.

If an interlock or other alarm condition exists, the four (4) LED’s will flash until

the alarm condition is cleared.

Water Meter

Each input may be programmed as water meter inputs that are capable of reading a dry contact

water meter. Input number one can be set to read a Hall Effect type water meter. Through

programming this input can be used to feed inhibitor as well as totalizing water consumption.

Alarm Relay (Relay #5)

MicroVision has a dedicated dry contact relay that can be used to interface with process control

equipment or visual indicators. This relay is un-powered and may also be programmed as a timer.

4-20mA Output

Connect your 4-20mA equipment to J8 (Fig. 7) pins + and -. The 4-20mA output uses 24VDC as a

supply voltage. See the “Conductivity Menu” section (Page 24) for setting up and calibrating the 4-

20mA output. When in the timed sample, or the sample and hold modes the 4-20mA output will only

update during the sample time and the hold times. During the interval times the output will remain at

the last sample value.

72-910-24 Revision H

INSTALLATION

Opening the Enclosure

Loosen the two (2) thumb screws to open the front cover of the controller, then loosen the

inside panel thumb screw and carefully swing the panel to the right (Fig. 2).

72-910-24 Revision H

Location

Select a mounting location convenient to grounded electrical and plumbing connections. It is

recommended that you mount the controller on a wall or other vertical surface with adequate

lighting at a comfortable level. A mounting-hole template is supplied with your controller.

Installation should comply with all national, state, and local codes.

AVOID LOCATIONS WHERE THE CONTROLLER WOULD BE SUBJECTED TO EXTREME

COLD OR HEAT {LESS THAN 0°F (-17,8°C) OR GREATER THAN 150 °F (65°C)}, DIRECT

SUNLIGHT,VIBRATION,VAPORS,LIQUID SPILLS,OR EMI (ELECTROMAGNET

INTERFERENCE;E.G., STRONG RADIO TRANSMISSION AND ELECTRIC MOTORS.)

SAFETY PROTECTION PROVIDED BY THE EQUIPMENT MAY BE IMPARED IF THE

EQUIPMENT IS USED IN A MANNER NOT SPECIFIED BY THE MANUFACTURER.

Fig. 3

Mount the controller using the four (4) holes provided (Fig. 3).

Mounting Hardware

Typically, use ¼” (6mm) or equivalent.

72-910-24 Revision H

Sensor Installation

The controller is supplied with a temperature compensated or non temperature conductivity

sensor (probe). The probe location must be in a position where adequate flow is going

around and through the probe (Fig. 4) so that the controller will be able to display a good

measurement. The two flats of the sensor must be perpendicular to flow as shown.

Fig. 4

72-910-24 Revision H

TYPICAL INSTALLATION

Fig. 5

72-910-24 Revision H

IMPORTANT SYMBOL INFORMATION

Warning indicates a condition that could cause damage to both the equipment

and the personnel operating it. Pay close attention to any warning.

Primary Supply Ground must be connected to earth ground for safe operation of

your controller.

Chassis Ground – Connect your equipment’s ground wire here for safe

operation of your external devices.

ELECTRICAL WIRING

CONTROLLER MUST BE WIRED IN ACCORDANCE WITH ALL APPLICABLE ELECTRICAL

CODES.

The MicroVision electronic input circuitry is fuse protected on both the hot and neutral inputs

using a replaceable five-amp fuse (Fig .6).

For additional protection of your instrument, use of a surge protector is recommended.

The controller should be connected to a dedicated power branch (i.e., its own wiring,

circuit breaker, etc.). For best results, the ground should be independent (true earth)

not shared.

A switch or circuit-breaker marked as the unit’s disconnecting device should be

included in the installation. It should be near the unit and be easily reached by the

operator

Pre-wired controllers are supplied with a 3-wire grounded power cord and 3-wire grounded

receptacle cords for all controlled line voltage outputs.

72-910-24 Revision H

RELAY BOARD CONNECTIONS

Fig. 6

Conduit Models (Wiring High Voltage)

Conduit controllers have openings for conduit connections for hard wiring. (See Fig. 6) for input and

output power connections. Use only 18 AWG (1,2 mm²) stranded wire for conduit power and load

connections. Supply (input) A/C power is connected via the terminal block located on the back panel

marked “A/C Power” (Fig. 6). The top part of this terminal block is removable to allow for easy

access to the connector’s three (3) screws.

MAKE SURE THAT YOUR CONTROLLER VOLTAGE MATCHES THE INPUT VOLTAGE.

DO NOT APPLY POWER UNTIL THIS CONDITION IS VERIFIED.

Make sure that all conduit connections are watertight.

The four (4) output relay terminal blocks are identified as: PL1 (bleed), PL2 (Inhib), PL3 (Bio A),

and PL4 (Bio B). The Blowdown relay has a N.O. and a N.C. connection, the others are only N.O.

Inhaltsverzeichnis

Andere Idex Controller Handbücher

Idex

Idex Pulsafeeder MPC Vector Gebrauchsanweisung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch